Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Yamaha PJP-50R
Summary of Contents for Yamaha PJP-50R
- Page 1 PJP-50R IP Audio Conference System Système de conférence audio IP MIC MUTE / STANDBY HOOK Basic Operation Guide Guide de fonctionnement de base Grundlegende Bedienungsanleitung OWNER’S MANUAL MODE D’EMPLOI BEDIENUNGSANLEITUNG...
- Page 2 IMPORTANT SAFETY INSTRUCTIONS Important Safety Instructions Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the CAUTION product and to protect it from overheating, and these RISK OF ELECTRIC SHOCK openings must not be blocked or covered. The openings DO NOT OPEN should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.
- Page 3 “ON”, please try to eliminate the problem by using requirements. Modifications not expressly approved one of the following measures: by Yamaha may void your authority, granted by the FCC, to use the product. Relocate either the product generating the interference or the device that is being affected by the interference.
- Page 4 If the PJP-50R causes harm to the telephone network, contains, among other information, a product identifier the telephone company will notify you in advance that in the format US:AAAEQ##TXXXX.
- Page 5 YAMAHA will ■ Special Instructions for U.K. Model not be held responsible for any damage resulting from use of this unit with a voltage other than specified.
-
Page 6: Table Of Contents
Contents INTRODUCTION CONFIGURATIONS Features ..............2 Configuring the Settings ........12 About this Manual ..........3 Configuring the settings using the keys Supplied Accessories ..........3 on this unit ............12 Controls and Functions ......... 4 Configuring the settings using the Web menu ..13 Setting the Menu List ...........14 Registering the IP network information .... -
Page 7: Features
Features This system is an audio conference system that connects IP networks including the Internet and corporate LAN as well as analog telephone circuits to hold simultaneous communications between multiple persons in multiple locations. Connection to IP network Communication through analog telephone circuit Internet, corporate LAN, etc. -
Page 8: About This Manual
Features About this Manual • In this manual, the names of the following products are denoted as follows. – Yamaha PJP-50R: this unit ® ® – Microsoft Windows : Windows ® ® – Microsoft Windows XP : Windows XP – 10BASE-T (100BASE-TX) cable: LAN cable •... -
Page 9: Controls And Functions
CONTROLS AND FUNCTIONS Controls and Functions ■ Top panel MIC MUTE / STANDBY HOOK 5 6 7 8 1 Microphone indicators (Up/Down) keys A blue LED lights to indicate the audio pick up area. Press either key to select a setting item or move the cursor up or down. -
Page 10: Step 1: Connecting This Unit
• IC REN (U.S. and Canada models only): Ringer Equivalence Number (REN) of this unit. 2 Arrayed speakers PJP-50R MODEL NO. The four arrayed speakers on the bottom panel for use in YAMAHA CORPORATION Registration NO. US : A6RTE00BPJP50R IC Registration NO. -
Page 11: Step 2: Registering The Settings Of This Unit
Controls and Functions ■ Display Example of the initial display Tel & IP ready (192.168.100.200) 2007.09.20 12:16:14 Menu :Address 2 3 4 5 6 7 8 9 1 Communication mode indicator 5 Room size indicator Indicates the communication mode used in the Indicates the room size setting. -
Page 12: Communication Through Ip Network
Communication through IP Network Communication through IP Network Calling another party To place a call to another party, enter its IP address. CAUTION Before using the functions of this system, it is necessary to install, connect, and set up the system. For details, refer to the “Setup guide”... -
Page 13: Calling Another Party Using The Address Book
Communication through IP Network The following display appears if the call is connected Calling another party using the and conversation becomes available. address book Follow the procedure below to call another party registered in the address book. 192.168.0.10 To use this function, it is required to use the PC for registering the addresses of the locations to be called in the Address Book. -
Page 14: Calling Another Party Using The Call History
Communication through IP Network Calling another party using the call Press to select the destination, and history then press The calling display appears. Follow the procedure below to call another party by referring to the history of past outgoing or incoming calls. Call History Note Headquarter... -
Page 15: Operations During Communication Through Ip Network
Operations during Communication through IP Network Operations during Communication through IP Network Adjusting the speaker volume • Zone (Default): Pick up the audio from a large area. This mode is suitable for a relatively quiet Press VOL + or – during communication to adjust the environment. -
Page 16: Step 3: Installing This Unit In The Conference Room
Operations during Communication through IP Network ■ Configuring the speaker mode You can select the audio output mode of the speakers Today... during a call. You can display the “Speaker Mode” menu by holding down in the initial display or calling display. MIC MUTE •... -
Page 17: Talking With Multiple Locations
Talking with Multiple Locations Talking with Multiple Locations This system enables simultaneous talk between up to four locations (with the mesh connection) through an IP network. It is also possible to call additional locations as required during a call. To hold a communication between multiple locations, begin a call with a single location and then call other required locations. -
Page 18: Display And Speaker Output During Multiple Connections
Talking with Multiple Locations Display and speaker output during For the display during communication using the SIP server, refer to “Display in SIP server operation” (page 25) in the “Setup multiple connections guide” (a separate manual). For the display during communication with cascade connections, refer to “Display in The information display and speaker output method vary cascade connection”... -
Page 19: Communication Through Telephone Circuit
Communication through Telephone Circuit Communication through Telephone Circuit Calling another party To place a call to another party, enter its telephone number. CAUTION • Before using the functions of this system, it is necessary to install, connect, and set up the system. For details, refer to the “Setup guide”... -
Page 20: Calling Another Party Using The Address Book
Communication through Telephone Circuit The following display appears if the call is connected Calling another party using the and conversation becomes available. address book Follow the procedure below to call another party registered in the address book. 408467 To use this function, it is required to use the PC for registering the telephone numbers of the locations to be called in the Address Menu :Address Book. -
Page 21: Calling Another Party Using The Call History
Communication through Telephone Circuit Calling another party using the call Press to select the destination, and history then press The calling display appears. Follow the procedure below to call another party by referring to the history of past outgoing or incoming calls. Call History Headquarter Press... -
Page 22: Operations During Communication Through Telephone Circuit
Operations during Communication through Telephone Circuit Operations during Communication through Telephone Circuit Adjusting the speaker volume • Zone (Default): Pick up the audio from a large area. This mode is suitable for a relatively quiet Press VOL + or – during communication to adjust the environment. - Page 23 Operations during Communication through Telephone Circuit ■ Configuring the speaker mode You can select the audio output mode of the speakers Today... during a call. If the connection is mode through the telephone circuit, the audio is output in monaural. You can display the “Speaker Mode”...
-
Page 24: Sending Tone Signals
Operations during Communication through Telephone Circuit Sending tone signals Transferring a call (Telephone circuit only) Tone signals can be transmitted during communication. This is convenient when using a service that requires tone A received call can be transferred to another extension input during a call, such as the answering service of a phone provided that the PBX accommodating this system cellular phone. -
Page 25: Troubleshooting
Refer to the following tables when this unit does not function properly. If the problem you are experiencing is not listed or if the instruction does not help, contact your nearest authorized YAMAHA dealer or service center. First, check if the microphone indicators light up. If the indicator is turned off, see “Q1: LED indicators do not light up”... -
Page 26: Q2: A Call Cannot Be Made
Troubleshooting Q2: A call cannot be made Problem Cause Remedy A call cannot be originated. An inappropriate IP address is entered. Check the IP address of the other unit and enter the correct IP address. The IP address of the other unit has been Check the IP address of the other unit and changed. -
Page 27: Q3: Other Problems
I forgot the password. Enter the master password (page 21 in the “Setup guide” (a separate manual)). The clock setting has been cleared. The built-in battery for clock information is Consult your nearest authorized Yamaha dead. dealer or service center. -
Page 28: Editing The Address Book
Daten können möglicherweise durch eine zukünftige Firmware- Aktualisierung erweitert oder geändert werden. Besuchen Sie die PJP-Website zum Erhalten der neuesten Firmware und Anleitungen. PJP-Website: http://www.yamaha.co.jp/english/product/projectphone/ © 2006 All rights reserved. YAMAHA CORPORATION 10-1 Nakazawa-cho, Hamamatsu, Shizuoka 430-8650, Japan As of October, 2007 Printed in Japan WJ13580-2...