Yamaha A5000 Service Manual page 36

A5000/A4000
5.3.1. Parameter change (object select)
0 01110000 $F0
1 01000011 $43
2 0001nnnn nnnn = Device Number
3 01011000 $58 g=22,h=0
4 00000000 $00
5 0ccccccc
20 0ccccccc
22 0ttttttt object type
21 11110111 $F7
Functions as an object select message.
This message specifies the object.
object name is a 16-character name for each object. Program object names are the pro-
gram number of each program (example: "001
The object type is shown in the following table.
t Data type
20($14) Program
17($11) Sample Bank
16($10) Sample
2($02) Wave data
19($13) Sequence
5.3.2. Parameter change (object edit)
0 11110000 $F0
1 01000011 $43
2 0001nnnn nnnn = Device Number
3 01011000 $58 g=22,h=0
4 00000001 $01
5 0ppppppp
10 0ppppppp
11 0ddddddd
0ddddddd
11110111 $F7
Changes the value of the object parameter specified by object select.
The parameters comply with P1, P2 — P6 in chart 2.
The number of data bytes depends on the parameter. The data section is divided into byte
1, which is the upper nibble, and byte 2, which is the lower nibble. See chart 2 for details.
5.3.3. Parameter change (system parameter)
0 11110000 $F0
1 01000011 $43
2 0001nnnn nnnn = Device Number
3 01011000 $58 g=22,h=0
4 00000010 $02
5 0ppppppp
10 0ppppppp
11 0ddddddd
0ddddddd
01110111 $F7
This message is a parameter change for system parameters.
The parameters comply with P1, P2 — P6 in chart 2.
The number of data bytes depends on the parameter. The data section is divided into byte
1, which is the upper nibble, and byte 2, which is the lower nibble. See chart 2 for details.
5.3.4. Parameter change (switch remote)
0 11110000 $F0
1 01000011 $43
2 0001nnnn nnnn = Device Number
3 01011000 $58 g=22,h=0
4 00000011 $03
5 0ppppppp switch number
6 00000000 $00
10 00000000 $00
11 0ddddddd data
27 11110111 $F7
This message performs remote control of switches.
For the switch numbers, refer to table 2.
With the exception of switch numbers 123-127, data of $00-$3F turns the switch off, and
data of $40-$7F turns the switch on.
For switch numbers 123-127 (knob encoders), a value of 64 less than the data specifies the
number of pulses which correspond to rotation (30 pulses per rotation). Positive numbers
are rotation toward the right, and negative numbers are rotation toward the left.
This message is received only.
36
object name (ASCII 16byte)
").
parameter number P1-P6 (6byte)
data
parameter number P1-P6 (6byte)
data
5.3.5. Parameter request (object)
0 11110000 $F0
1 01000011 $43
2 0011nnnn nnnn = Device Number
3 01011000 $58 g=22,h=0
4 00000001 $01
5 0ppppppp
parameter number P1-P6 (6byte)
10 0ppppppp
11 11110111 $F7
This message requests transmission of the parameter of the specified object as a parameter
change.
The parameters comply with P1, P2 — P6 in chart 2.
This message is received only.
5.3.6. Parameter request (system parameter)
0 11110000 $F0
1 01000011 $43
2 0011nnnn nnnn = Device Number
3 01011000 $58 g=22,h=0
4 00000010 $02
5 0ppppppp
parameter number P1-P6 (6byte)
10 0ppppppp
11 11110111 $F7
This message requests transmission of a system parameter as a parameter change.
The parameters comply with P1, P2 — P6 in chart 2.
This message is received only.
5.3.7. Object Link Change
0 11110000 $F0
1 01000011 $43
2 0001nnnn nnnn = Device Number
3 01011000 $58 g=22,h=0
4 00000100 $04
5 0ccccccc
upper object name (ASCII 16byte)
20 0ccccccc
21 0ttttttt upper object type
22 0ccccccc
lower object name (ASCII 16byte)
37 0ccccccc
38 0ttttttt lower object type
39 0ddddddd data (0:link off, 1:link on)
40 11110111 $F7
Changes the link condition between specified objects (between Program and Sample/
Sample Bank Program is upper, and between Sample Bank and Sample is upper). Nothing
occurs when an object is selected which is not changeable, or which requires samples to
be copied.
object name is a 16-character name for each object. Program object names are the pro-
gram number of each program (example: "001
The object type is shown in the following table.
t Data type
20($14) Program
17($11) Sample Bank
16($10) Sample
5.3.8. Object Link Request
0 11110000 $F0
1 01000011 $43
2 0011nnnn nnnn = Device Number
3 01011000 $58 g=22,h=0
4 00000100 $04
5 0ccccccc
upper object name (ASCII 16byte)
20 0ccccccc
21 0ttttttt upper object type
22 0ccccccc
lower object name (ASCII 16byte)
37 0ccccccc
38 0ttttttt lower object type
39 0ddddddd data (0:link off, 1:link on)
40 11110111 $F7
When received the link condition between specified objects (between Program and Sample/
Sample Bank Program is upper, and between Sample Bank and Sample is upper) is trans-
mitted in object link change format. This message is receive only.
The object type is shown in the following table.
t Data type
20($14) Program
17($11) Sample Bank
16($10) Sample
").