Development And Evaluation Tools; Rcm4510W Development Kit - RabbitCore RCM4500W User Manual

1.3 Development and Evaluation Tools

1.3.1 RCM4510W Development Kit

The RCM4510W Development Kit contains the hardware essentials you will need to use the
RCM4510W module. The items in the Development Kit and their use are as follows.
• RCM4510W module.
• Prototyping Board.
• Universal AC adapter, 12 V DC, 1 A (includes Canada/Japan/U.S., Australia/N.Z., U.K., and
European style plugs). Development Kits sold in North America may contain an AC adapter
with only a North American style plug.
• USB programming cable with 10-pin header.
• 10-pin header to DB9 serial cable.
•
14-pin IDC socket connector with bare leads ribbon cable.
®
• Digi XBee USB (used as ZigBee coordinator).
®
• Dynamic C CD-ROM, with complete product documentation on disk.
• Getting Started instructions.
• A bag of accessory parts for use on the Prototyping Board.
• Rabbit 4000 Processor Easy Reference poster.
• Registration card.
Programming
Cable
G
G
bbitCore RCM4510W
10W RabbitCore module features built-in ZigBee ® /802.15.4 connectivity, allowing you to create
ow-power, wireless network as part of your control solution for your embedded application.
g Started instructions included with the Development Kit will help you get your RCM4510W
ng so that you can run the sample programs to explore its capabilities and develop your own
ment Kit Contents
510W Development Kit contains the following items
0W module (with XBee Series 2 ZigBee module installed).
ng Board.
AC adapter, 12 V DC, 1 A (includes Canada/Japan/U.S., Australia/N.Z., U.K., and European
s).
gramming cable with 10-pin header.
ader to DB9 serial cable.
C socket connector with bare leads ribbon cable.
Bee USB (used as ZigBee ® coordinator).
C ® CD-ROM, with complete product documentation on disk.
tarted instructions.
d metal standoffs with 4-40 screws and washers.
accessory parts for use on the Prototyping
®
Installing Dynamic C
000 Processor Easy Reference poster. Insert the CD from the Development Kit in
on card. your PC's CD-ROM drive. If the installation
does not auto-start, run the setup.exe pro-
ine Rabbit store at www.rabbit.com/store/ for gram in the root directory of the Dynamic C
ormation on peripherals and accessories that CD. Install any Dynamic C modules after you
for the RCM4510W RabbitCore modules. install Dynamic C .
amic C are registered trademarks of Rabbit Semiconductor Inc. Digi is a registered trademark of Digi International Inc.
stered trademark of the ZigBee Alliance.
tti St t d
User's Manual
Accessory Parts for
Digi XBee
Prototyping Board
USB
Serial
Cable
RX43
RX97 RX49
Socket
UX3
Figure 2. RCM4510W Development Kit
Universal
AC Adapter
with Plugs
U1
C1 1
C2 BT1
UX47 UX49 UX4
C5 J2
L1 C6 +5 V
GND
GND
/RST_OUT /IORD +3.3 V
RCM1 /IOWR /RST_IN RX81
VBAT
EXT PA0
PA1 PA2
PA3 PA4 RX83
JP16 JP6 PA5 PA6
C18 JP12 JP5
U3 JP4 PA7 PB0
JP14 JP3 PB1 PB2
C16 JP7 JP8
JP18 PB3 PB4 RX11
JP10 JP9 PB5 PB6
R25 PB7 PC0
C15 PC1 PC2
Q1 PC3 PC4 UX10
PC5 PC6
R29 PC7 PE0 RX67
PE1 PE2 UX12
R20 R19 PE3 PE4
PE5 PE6
R10 R9 PD0
PE7 LN0
LN1 PD1 LN2 PD2
PD3 PD4
LN3 LN4 UX14
LN5 PD5 LN6 PD6
RX55 RX57 RX59 PD7 RX75
LN7 CVT RX73 CX27
VREF AGND
DS2 CX25 CX23 RX77 DS3 RX79
R21 UX16
JP25 R23 R22 R24
J3
1 1 GND
S1
RESET
UX30
5