Table of Contents
Advertisement
Quick Links
© Copyright 1994
Magnadyne Corporation
R
Installation
and Operations
•
FF / EJ
VOL
POWER
FAD
BALANCE
TONE
BAND
1
2
3
SEEK
4
5
6
F/C
M9000 AM/FM Stereo Receiver and
Auto Stop Cassette Deck
•
EJECT
VOL
BAL
POWER
PULL
FAD
BASS
TREB
BAND
1
2
3
SEEK
4
5
6
F/C
M9050H High Power AM/FM Stereo
Receiver and Auto Reverse
Manual
AUTO STORAGE PRESET MEMORY
AUTO STOP CASSETTE
TUNE
SEEK
UP
FM 1 2 3
AM ST
AS
PLL SYNTHESIZER TUNER
DOWN
<<
AUTO STORAGE PRESET MEMORY
HIGH POWER 25 + 25
AUTO REVERSE CASSETTE
TUNE
UP
FM 1 2 3
AM ST
AS
PLL SYNTHESIZER TUNER
DOWN
Cassette Deck
CH
>>
. PROG .
CH
Advertisement
Table of Contents
Related Manuals for Magnadyne M9000
Summary of Contents for Magnadyne M9000
- Page 1 AUTO STORAGE PRESET MEMORY AUTO STOP CASSETTE TUNE SEEK BAND FM 1 2 3 SEEK AM ST PLL SYNTHESIZER TUNER DOWN M9000 AM/FM Stereo Receiver and Auto Stop Cassette Deck << >> . PROG . • EJECT POWER PULL BASS...
-
Page 2: Mechanical Installation
Space Requirements: sent will require some type of custom installation bracketry or “kit” to properly To mount your new Magnadyne unit, you install your new Magnadyne radio. In will need a rectangle hole in the mount- addition, many new or late model vehicles... -
Page 3: Installation Procedure
Installation Procedure Step 1: Step 4: After obtaining the required space and Securely attach the rear support strap pro- mounting hold dimensions required, vided to the rear of the unit with the fas- release the mounting sleeve from the unit teners provided. - Page 4 Installation Procedure Figure 1 Sheet Metal Screw Washer Metal Strap Dashboard Mounting Sleeve Removing the Unit Removal Keys...
- Page 5 In addition, tory radio in the event you sell your vehi- shared grounds tend to amplify engine cle and want to keep your Magnadyne noise into the unit and you will hear the unit. noise in your speakers.
-
Page 6: Speaker Connections
Brown Wire: connected to it. To properly connect the Connect the Brown wire to the Left speak- speaker system to your new Magnadyne er “Positive” wire. radio, you must have a + and - wire com- ing from every speaker to connect to the Orange Wire: unit. - Page 7 Red Wire Connect to Ignition 12V White Wire Gray Wire Yellow Wire +12 Output for Power Antenna Right Front Speaker Right Rear Speaker Two Speaker Wiring (M9000 Only) Left Speaker Brown Wire 9-Pin Plug From Orange Wire No Connection Radio...
-
Page 8: Radio Operation
Radio Operation To turn on the unit and operate the radio, repeat the following procedures. 1. Turning the Unit On M9000/M9050H Rotate the VOL knob to the right until it • POWER clicks to turn the unit on M9000/M9050H 2. Radio Band Selection (All Models) To select the AM or FM radio band press ☛... - Page 9 Radio Operation For automatic seek tuning, press the SEEK M9000/M9050H M9050H-2 button once and the tuner will automati- AUTO cally seek to the next strongest station. When a strong station is picked up by the tuner the station will lock on and be dis- ☛...
- Page 10 TREB (M9050H Only) Rotate this control clockwise to increase the bass tone and counter clockwise to decrease the bass tone. Balance Control: (M9000 ) M9000 Rotate the balance control left or right to POWER BALANCE achieve the desired left and right speaker output to suit your listening taste.
-
Page 11: Programming The Unit
1. With the unit on, make sure the display SEEK is showing the clock by pressing the “F/C” ☛ button. 2. Press and hold down the F/C button. M9000 / M9050H ☛ 3. While holding down the F/C button, TUNE BAND Minutes... - Page 12 Programming the Unit Entering Radio Stations into Memory: M9000/M9050H (All Models) ☛ 1. Use the VOL switch to turn the unit on BAND SEEK 2. Use the BAND button to select the M9000/M9050H memory group you want to store the radio Memory Groups stations in.
-
Page 13: Tape Operation
(thick end) facing to the right. Push the tape all the way in until the cassette mechanism is engaged. Note: (M9000 Only) The side of the tape that is pointing up is the side that will be played. - Page 14 EJ/FF button until it locks. To release FF / EJ BALANCE TONE the FF button, press it in until it releases ☛ and the tape will begin to play. (M9000 AUTO STORAG AUTO ST only) 4B. To fast forward the tape, press the M9050H...
-
Page 15: Care And Maintenance
10 to 15 Speaker Impedance Requirement...4 or 8 Ohm hours of playing time. If you record your own Output Power..(M9000) 5 Watts x 2 @ 1% THD tapes on high quality CRO2 or metal tape, you Output Power....(M9050H/M9050H-2) should clean the head about once a month. -
Page 16: Warranty
Warranty ONE (1) YEAR LIMITED WARRANTY Magnadyne Corporation or its authorized agents will within 1 year from the date of sale to you, repair, replace or refund the retail sales price of said product or any part thereof, at the option of the Magnadyne Corporation or its authorized agents, if said product or part is found defective in materials or workmanship, when properly connected and operating on the correct power requirements designated for the specific product.