Related Manuals for Woodward easYgen-2500
Summary of Contents for Woodward easYgen-2500
- Page 1 Series Option Manual Genset Control easYgen-2500 Rental (Option K33) Software Version 1.00xx 37537...
- Page 2 Woodward GmbH Handwerkstrasse 29 70565 Stuttgart Germany Telephone: +49 (0) 711 789 54-0 Fax: +49 (0) 711 789 54-100 email: stgt-info@woodward.com Internet: http://www.woodward.com © 2011 easYgen-2500 Rental (Option K33) | Genset Control 37537...
- Page 3 – P/N 5417-557 The easYgen-2000 Series are control units for engine-generator system management applications. The control units can be used in applications such as: rental gener- ators, stand-by, AMF and peak shaving. 37537 easYgen-2500 Rental (Option K33) | Genset Control...
- Page 4 The control unit can open and close the generator circuit breaker (GCB). For a listing of additional application modes and setups please refer to 'Chapter: Application' in easYgen-2200/2500 manual (37535). easYgen-2500 Rental (Option K33) | Genset Control 37537...
- Page 5 Brief Overview Additional functionality The easYgen-2500 Rental controllers have some addi- tional features compared to the standard easYgen-2500 controllers. The differences are listed below. Ä Chapter – Switchable parameter sets. Refer to 2.1.1 ‘Switchable Parameter Sets’ on page 15 for details.
- Page 6 Brief Overview easYgen-2500 Rental (Option K33) | Genset Control 37537...
-
Page 7: Table Of Contents
Configure Counters........................21 Operation........................... 21 2.2.1 Front Panel Access........................21 Appendix........................... 22 2.3.1 Data Protocols........................... 22 2.3.2 LogicsManager Reference......................23 2.3.3 Event And Alarm Reference...................... 24 Glossary And List Of Abbreviations..................25 Index............................27 37537 easYgen-2500 Rental (Option K33) | Genset Control... - Page 8 Table of contents easYgen-2500 Rental (Option K33) | Genset Control 37537...
-
Page 9: General Information
This symbol indicates useful tips and recommenda- tions as well as information for efficient and trouble- free operation. Additional markings To emphasize instructions, results, lists, references, and other ele- ments, the following markings are used in these instructions: 37537 easYgen-2500 Rental (Option K33) | Genset Control... -
Page 10: Copyright And Disclaimer
Woodward GmbH assumes no liability for damages due to: Failure to comply with the instructions in this operating manual... -
Page 11: Safety
– Therefore, all work must only be carried out by appropriately qualified personnel. This manual specifies the personnel qualifications required for the different areas of work, listed below: 37537 easYgen-2500 Rental (Option K33) | Genset Control... -
Page 12: General Safety Notes
Rental (Option K33) | Genset Control 37537... - Page 13 Keep plastic, vinyl, and Styrofoam materials (such as plastic or Styrofoam cups, cigarette packages, cellophane wrappers, vinyl books or folders, plastic bottles, etc.) away from the control unit, modules and work area. 37537 easYgen-2500 Rental (Option K33) | Genset Control...
-
Page 14: Protective Equipment And Tools
Use of the proper tools ensures successful and safe execution of tasks presented in this manual. Specific required tools are listed in each individual set of instruc- tions. The cumulative required tools are detailed below: easYgen-2500 Rental (Option K33) | Genset Control 37537... -
Page 15: Additional Functionality
1752 [kW] p. 17 p. 17 p. 17 p. 17 Gen. rated react. power 4758 Ä 4779 Ä 4800 Ä 4821 Ä 1758 [kvar] p. 17 p. 17 p. 18 p. 18 37537 easYgen-2500 Rental (Option K33) | Genset Control... - Page 16 Engine rated 500 to 4,000 Number of revolutions per minute of the engine at rated engine speed. The speed speed control with an ECU via J1939 CAN bus refers to this value. easYgen-2500 Rental (Option K33) | Genset Control 37537...
- Page 17 This value specifies the generator reactive power rating, which is used as a react. power kvar reference figure for related functions. The generator rated reactive power also 4779 [kvar] depends on the generator values ( Ä ‘Dependencies’ on page 16). 37537 easYgen-2500 Rental (Option K33) | Genset Control...
- Page 18 0.0 to 9999.9 The load setpoint 1 is defined in this screen. This value is the reference for trol setpoint 1 the load controller when performing parallel operations. 4786 [100.0 kW] 4807 easYgen-2500 Rental (Option K33) | Genset Control 37537...
- Page 19 The control unit will function as a 1 CB unit. The control unit performs full con- trol like synchronizing, opening and closing the GCB with generator and engine protection. All necessary inputs and outputs are assigned and pre- defined. 7454: [GCB/ Application mode MCB] 37537 easYgen-2500 Rental (Option K33) | Genset Control...
- Page 20 Once the conditions of the LogicsManager have been fulfilled, parameter set LogicsManager 4 will be enabled. [(0 & 1) & 1] Notes The default "Parameter Set 1" is used, if more than one parameter set is ena- bled simultaneously. easYgen-2500 Rental (Option K33) | Genset Control 37537...
-
Page 21: Configure Counters
Counters configuration The counters configuration screen has been extended by entries for the direct access to following parameters: Reset period of use counter Codelevel for reset per. of use Fig. 8: Counters configuration 37537 easYgen-2500 Rental (Option K33) | Genset Control... -
Page 22: Appendix
Mask: 0400h Internal Mask: 0200h Internal Mask: 0100h Internal Mask: 0080h Internal Mask: 0040h Internal Mask: 0020h Internal Mask: 0010h Internal Mask: 0008h Parameter set 4 Mask: 0004h Parameter set 3 Mask: 0002h easYgen-2500 Rental (Option K33) | Genset Control 37537... -
Page 23: Logicsmanager Reference
Parameter set 4 Mask: 0004h Parameter set 3 Mask: 0002h Parameter set 2 Mask: 0001h 450110 450109 3,4,5,6 2580 Period of use counter 2.3.2 LogicsManager Reference Logical command variables Group 24: Flags condition 2 37537 easYgen-2500 Rental (Option K33) | Genset Control... -
Page 24: Event And Alarm Reference
Message text Meaning ..Set change Set change 13285 Once the parameter set is changed, the original parameters will be updated. This process could take a few seconds. easYgen-2500 Rental (Option K33) | Genset Control 37537... -
Page 25: Glossary And List Of Abbreviations
Normally Open (make) contact Occurrence Count Real power Part Number Power Factor Proportional Integral Derivative controller Programmable Logic Control Potential (Voltage) Transformer Reactive power Apparent power Serial Number Suspect Parameter Number Voltage 37537 easYgen-2500 Rental (Option K33) | Genset Control... - Page 26 Glossary And List Of Abbreviations easYgen-2500 Rental (Option K33) | Genset Control 37537...
-
Page 27: Index
Index Index Contact person............. 10 Service..............10 Customer Service..........10 Symbols in the instructions..........9 Intended use............11 Use............... 11 Personnel............. 11 Protective equipment........... 14 Warranty............... 11 37537 easYgen-2500 Rental (Option K33) | Genset Control... - Page 28 Index easYgen-2500 Rental (Option K33) | Genset Control 37537...
- Page 29 37537 easYgen-2500 Rental (Option K33) | Genset Control...
- Page 30 Rental (Option K33) | Genset Control 37537...
- Page 32 Woodward GmbH Handwerkstrasse 29 - 70565 Stuttgart - Germany Phone +49 (0) 711 789 54-0 ∙ Fax +49 (0) 711 789 54-100 stgt-info@woodward.com...