Nordson iTRAX Product Manual
  1. Manuals
  2. Brands
  3. Nordson Manuals
  4. Monitor
  5. iTrax
  6. Product manual
Nordson iTRAX Product Manual

Nordson iTRAX Product Manual

Remote display
Hide thumbs Also See for iTRAX:
Table of Contents

Advertisement

Quick Links

Download this manual
r
iTRAX
Remote Display
Customer Product Manual
Part 1076079A
Issued 11/07
For parts and technical support, call the Industrial Coating
Systems Customer Support Center at (800) 433-9319 or
contact your local Nordson representative.
This document is subject to change without notice.
Check http://emanuals.nordson.com for the latest version.
NORDSON CORPORATION  AMHERST, OHIO  USA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the iTRAX and is the answer not in the manual?

Questions and answers

Zbigniew Skorek
April 24, 2025

I would like to introduce new recipe to itrax. Ball Plzen Czech Republic. How to do it?

0
1 comments:
Mr. Anderson
May 12, 2025

To introduce a new recipe to the Nordson iTRAX:

1. Touch the Save Current Configuration as Recipe button.
2. Change the recipe settings as needed in each module configuration window.
3. Once changes are made, touch the OK button.
4. A dialog box will appear. Choose Save as Recipe to save the current settings, or Cancel to discard them.
5. If saving, touch the Recipe button to open the Recipe window.
6. Enter a name for the new recipe in the top field.
7. Touch Save Current Configuration as Recipe again to finalize and save the new recipe.

The new recipe name will then appear in the recipe field.

This answer is automatically generated

0

Subscribe to Our Youtube Channel

Related Manuals for Nordson iTRAX

Summary of Contents for Nordson iTRAX

  • Page 1 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative. This document is subject to change without notice. Check http://emanuals.nordson.com for the latest version. NORDSON CORPORATION  AMHERST, OHIO  USA...

  • Page 2: Table Of Contents

    Notice Nordson Corporation welcomes requests for information, comments, and This is a Nordson Corporation publication which is protected by copyright. inquiries about its products. General information about Nordson can be Original copyright date 2007. No part of this document may be...

  • Page 3: Description

    Monitors or one iTrax Pressure Control system. Spray Monitor Process Data The Remote Display receives and displays process data from 1 to 4 iTRAX Spray Monitors when the communication interface is configured for a CAN bus. The operator can choose to display any or all of the following data...

  • Page 4: Operator Interface

    Operator Interface Process Data Display: Displays process data. Nordson Key: Toggles the scrolling of process data and gun channels on and off. Press once to lock, again to unlock. Units Display: In Display mode, displays the Engineering Units for the currently displayed process data.

  • Page 5: Installation

    Remote Display Installation RS485 RS485 24 Vdc 24 Vdc Module 24 Vdc Pressure Remote Power Controller Display Supply 24 Vdc Spray Remote Monitors Display 24 Vdc Power Supply Figure 2 Remote Display Connections: PRx Module or Spray Monitors Mount the Remote Display in a suitable location where it is visible to the coating line operators.

  • Page 6: Rs485 Wiring And Termination

    Install JP1 jumper on both pins. This terminates the RS485 bus. CAN Wiring and Bus Termination Recommended CAN Cables If installing the Remote Display on a CAN bus with iTRAX Spray Monitors, the following CAN cables are recommended: Belden 9841 (2 wire, communications only) Belden 3084A (4 wire, power and communications) Refer to Figure 4 for suggested CAN bus configurations.

  • Page 7: Can Bus Termination

    Remote Display Connections CAN Bus Termination A CAN bus can have up to 63 devices on it (1-63), including the iTrax PC. On the CAN bus used with the iTRAX Spray Monitors, each end of the bus must be terminated with a 120 ohm resistor.

  • Page 8: Configuration

    Configuration The Remote Display configuration procedure changes depending on the devices it is used with: iTRAX Spray Monitors or an iTRAX PRx module. When the Remote Display is powered up it goes through a self test and then loads the configured settings. If no settings have been made then it loads the defaults.

  • Page 9: Configuration - Spray Monitor Data

    Remote Display Configuration - Spray Monitor Data Make the following required and optional settings to configure the Remote Display to display Spray Monitor data. See Figure 5 for the menu map. Mode Function, Range, and Default MODE Mode to enter: DISP (Display mode) or CONF (Configuration mode). Pressing the Select key while in Display mode automatically sets the mode to CONF.

  • Page 10: Configuration Menu Map For Spray Monitor Data

    Remote Display Configuration Menu Map for Spray Monitor Data V-XX MODE COMM PRIO INTR DATA UNIT GUNS ENGL GUN1 DISP BASE CONF CAN1 METR GUN2 DATA FIRE SAVE GUN3 SAVE CAN2 GDUR SAVE SAVE G-ON GUN4 G-OF SAVE SAVE...

  • Page 11: Data Configuration Procedure

    Remote Display Data Configuration Procedure This example sets the process value data to display: 1. Press the Select key to enter configuration mode. Press the Select key to scroll through the configuration menu items. 2. On DATA press the Enter key.

  • Page 12: Configuration Menu Map For Prx Module Data

    Remote Display Configuration Menu Map for PRx Module Data MODE COMM V-XX INTR DATA UNIT ADDR DISP ENGL BASE 0001 METR CAN1 CONF 0004 TEMP SAVE SAVE CAN2 SAVE SAVE SAVE Figure 6 Configuration Menu Map for PRx Module Data...

  • Page 13: Operation

    Priority setting in configuration. To stop scrolling, press the Nordson key. The process value for the current gun channel will be displayed until you press the Nordson key again.

  • Page 14: Parts

    Remote Display Parts To order parts or components, call the Nordson Finishing Customer Support Center at (800) 433-9319 or contact your local Nordson representative. Part Description Note 1079966 DISPLAY, remote LED display NOTE A: There are no repair parts for the Remote Display.

  • Page 15: Declaration Of Conformity

    DECLARATION of CONFORMITY PRODUCT: iTrax Remote Display APPLICABLE DIRECTIVES: 98/37/EEC (Machinery) 2006/95/EC (Low Voltage Directive) 2004/108/EEC (Electromagnetic Compatibility Directive) STANDARDS USED TO VERIFY COMPLIANCE: EN12100 EN55011 EN61010 EN61000-4 Series PRINCIPLES: This product has been manufactured according to good engineering practice.

Table of Contents