Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Neets SB1
Summary of Contents for Neets SB1
- Page 1 Manual Sound Bar - SB1 Installation Manual...
-
Page 2: Foreword
Foreword This document describes how to install and operate the Neets Sound Bar - SB1. COPYRIGHT - All information contained in this manual is the intellectual property and copyrighted material of Neets. All rights are reserved. No third party is allowed access to content, information or data in this manual without Neets’... -
Page 3: Important Safety Instructions
Contact your local Neets reseller or distributor. • If the equipment has slots or holes in the enclosure, these are provided to prevent overheating of sensitive components inside. -
Page 4: Table Of Contents
Contents Foreword ............. . 2 Revision list . -
Page 5: Description
The Neets Sound Bar - SB1 is simple and advanced at the same time. It can simply be connected to the display and use the wake-on-signal feature or it can integrate with a control system through the RS-232 port. -
Page 6: Specifications
Specifications Neets Sound Bar SB1 Audio output RS-232 Output power 4 x 20 Wrms Ports 1 x bidirectional THD+N < 0.1 % @ 1 W Baud rate 19200 bit/sec Data bits Woofer 2 x 4” dual magnet, sandwich membrane Parity... -
Page 7: Installation
Installation Neets Sound Bar - SB1 is designed to be easily installed, in any convenient location. It can be hung on the wall beneath, or above a screen, or placed on a desk free standing. To use the Sound Bar freestanding on a desk, simply unpack the unit mount the adhesive feet, and it is ready to go. -
Page 8: Connection And Controls
Connection and Controls Front Number Description Power/standby indication led Power/standby indication LED The LED indicate the current state of the Sound Bar: • When powered on the LED will light up • When Powered off the LED will be off •... -
Page 9: Rs-232 Connector
Connect Rx from Sound Bar to transmit/Tx from control system, and Tx from Sound Bar to receive/Rx from control system. RS-232 BALANCED UNBALANCED OPTICAL Neets Control Sierra II, EU P/N#: Auto RS-232 I/O 1 +12V On/Off... -
Page 10: Unbalanced Audio
DC input and connect the mains cable to the AC supply only after all other connections to the Sound Bar have been made. Use only the included Neets mains power adaptor to supply power to the Sound Bar. -
Page 11: How To Use
How to use The mode select switch The mode selection switch is used to select between RS-232 control mode and Auto On/Off mode. Auto On/Off mode When the switch is set in the Auto On/Off mode the Sound Bar will activate the Wake-on-signal function and work autonomously powering on and off as described in “Wake-on-signal”... -
Page 12: Wake-On-Signal Technology
Wake-on-signal technology The Sound Bar is equipped with Wake-on-signal technology. This means that the Sound Bar is able to automatically power on and off, if there is a signal present on one of the three connected sources. When the Sound Bar is powered off the Sound Bar will sense on the audio inputs for one second at a time in a circular manner. -
Page 13: Troubleshooting
RS-232 protocol Command structure The Neets RS-232 protocol is structured in a special way, which is described here. The protocol consist of commands to control the Sound Bar and queries to request status from the Sound Bar. Both commands and queries is a two way data exchange where the command or query is sent to the Sound Bar. -
Page 14: Commands Or Queries To The Sound Bar
Commands or queries send to the Sound Bar Commands or queries to the Sound Bar is always structured the same way: A header: “NEUNIT=1” all commands, queries and replies start with the header The header and following command is delimited by a comma mark “,” Followed by the command: “POWER=ON”... -
Page 15: Global Functions
Global functions In the global functions, all the functions allowed to adjust the basic functions of the Sound Bar is showen. All commands start with “NEUNIT=1,” followed by the command in <A>, the value after the equal sign must be replaced with the value in <X> or a question mark, all commands must end with a \ Description <A>... -
Page 16: Audio Output Settings
Audio input settings Audio input settings are used to adjust settings for Wake-on-signal settings. All commands start with: NEUNIT=1,SETTINGS=INPUT, followed by the command in <A>, the value after the equal sign must be replaced with the value in <X> or a question mark, all commands must end with a \CR.