Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Winterhalter PT-500
Summary of Contents for Winterhalter PT-500
- Page 1 Rack pass-through dishwasher PT-500 Operating instructions...
-
Page 3: Table Of Contents
About this manual Operating instructions for Winterhalter PT-500 rack pass-through dishwasher (translation of the original German operating instructions) Table of contents About this manual -------------------------------- 2 Malfunctions -------------------------------------- 13 Safety notes ---------------------------------------- 2 9.1 Poor cleaning result ------------------------------ 14 2.1 Proper use ------------------------------------------- 2 Info Level ------------------------------------------- 15 2.2 Improper use ---------------------------------------- 2... -
Page 4: About This Manual
Safety notes 2.1 Proper use The PT-500 dishwasher is a technical device for commercial use and is not intended for private use. Use the dishwasher only for the washing of dishes such as plates, cups, cutlery and trays or for washing glasses of a gastronomic and related type. -
Page 5: Electrical Safety
Notify an authorized service technician or your retailer if another fault has occurred. If the mains cable of this device is damaged, it must be replaced by the Winterhalter or its Cus- tomer Service or another qualified person in order to prevent hazards. The mains cable must be H07 RN-F type or equivalent. -
Page 6: Product Description
Product description Product description 4.1 Mode of operation The boiler and the tank fill and are warmed up to the operating temperature after the machine is switched on. The display lights up in red during the warm-up phase. When the target temperatures are reached, the ma- chine is ready for use. -
Page 7: Operating Panel And Washing Programmes
A rinse aid is necessary to ensure that water on the dishes drains off after washing and dries off after a short while. Rinse aid is automatically dosed from an external container. The rinse aid dosing device is an integral component of the machine. The service engineer authorised by Winterhalter sets the dosing level when ... -
Page 8: Detergent
Rinse aid and detergent 5.2 Detergent Do not use acidic detergents. Do not mix different detergent products in order to prevent crystallisation which could de- stroy the detergent dosing device ( 5 .4). Caution Do not use products that can create foam, e.g. hand soap, soft soap, hand wash liquid. En- sure that these do not enter the machine even during the pre-treatment of the dishes. -
Page 9: Changing The Detergent Product
A new detergent product usually requires a new setting of the detergent dosing device. Assign the re- quired work to a service engineer authorised by Winterhalter to attain good results. If this is not done, the warranty and product liability of Winterhalter Gastronom GmbH expires. Procedure: ... -
Page 10: Filling Regeneration Salt
Operation 6.2 Filling regeneration salt Possible risk of damage to the water softener Chemicals such as detergent and rinse aid inevitably lead to damage to the water softener. Fill only with regeneration salt or pure evaporated salt. Caution Possible malfunction of the water softener ... -
Page 11: Washing
Operation 7.3 Washing Possible risk of scalding from hot wash water Keep children away from the dishwasher. The wash water is at a temperature of approx. 62 °C. Warning Do not open the hood while the machine is washing. There is a risk of the hot wash water ... -
Page 12: Switching Off
Servicing and maintenance 7.3.4 Changing washing programme Select a new washing programme. The symbol for the washing programme appears in the display. Close the hood. The washing programme is started. 7.3.5 End of the programme The display flashes green, as soon as the washing programme has ended and the hood remains unopened. 7.3.6 Prematurely terminating the washing programme A washing programme can be terminated in the following ways:... - Page 13 Servicing and maintenance 8.1.2 Self-cleaning programme at the end of the working day The machine is equipped with a self-cleaning programme that assists you when you are cleaning the inside of the machine. Proceed in accordance with Figures C1 to C20. Terminating the self-cleaning programme ...
-
Page 14: Weekly Cleaning
Clean the dirt filter in the dirt trap. 8.4 Maintenance by the Customer Service We recommend that you have an authorised Winterhalter service engineer carry out the maintenance of the machine at least once a year so that vulnerable parts can be checked and replaced accordingly. Original spare parts must be used for repairs and the replacement of worn parts. -
Page 15: Malfunctions
Do not open any machine covers or machine parts if it requires tools. There is danger of shock. Danger Only a Winterhalter service engineer should carry out work on the electrical system. The machine must first be disconnected from the mains. Faults are displayed in the display in the form of pictograms. -
Page 16: Poor Cleaning Result
Malfunctions 9.1 Poor cleaning result Possible cause Remedy Set the dosing amount as per the manu- facturer’s specifications ( 1 2) No or low detergent dosing Check the dosing lines (for kinks, break- age, ...) Replace the storage container if empty The dishes do not get clean Dishes incorrectly sorted Do not stack dishes one over the other... -
Page 17: Info Level
Info Level 10 Info Level In the Info Level you can retrieve the following information: Temperature in the boiler Temperature in the tank Serial number Calling Info Level Press the button. The following information is shown in the display: Temperature in the boiler Temperature in the tank Serial number... -
Page 18: Pin Menu
PIN Menu 12 PIN Menu You can carry out the following activities in the PIN menu: Set the dosing of the detergent and rinse aid for each programme Prime the rinse aid dosing device Prime the detergent dosing device ... - Page 19 PIN Menu (A) Integral detergent dosing device Priming the dosing device = Output screen Confirm with the button. The next screen is displayed. Keep the button pressed. The dosing device is primed. Go back with the button.
- Page 20 PIN Menu (B) Integral rinse aid dosing device Priming the dosing device = Output screen Press the button. Confirm with the button. The next screen is displayed. Keep the button pressed. The dosing device is primed. ...
-
Page 21: Installing The Machine And Tables
30002147 is available. 13.2 Building tables Assemble tables. When Winterhalter tables are used, attach aluminium strut supports to the machine. The aluminium strut supports are in the machine. Secure the tables to the machine. -
Page 22: Water Connection
Water connection With separately available guide bars, the rack guide can be converted to the following rack sizes and wall distances: Rack size Distance between the wall and rear of the rack guide 500 x 500 mm 170 mm 530 x 530 mm 155 mm 140 –... -
Page 23: Electrical Connection
Electrical connection 15 Electrical connection Danger to life. Live components. The machine and the relevant additional devices must be connected by an electrical company authorised by the relevant electricity supplier as per the locally applicable standards and regulations. Danger ... -
Page 24: Connection Diagram
Electrical connection 15.3 Connection diagram... -
Page 25: External Dosing Devices
16 External dosing devices Instead of the integral dosing device, external dosing devices can also be used. Follow the instructions in this section. Additional information can be found in German and English on the Winterhalter web site (Dosiertechnik / Dosing systems). -
Page 26: Electrical Connection
External dosing devices 16.2 Electrical connection IMPORTANT maximum current drain at the transfer strip: 0.5 A. Connect the external dosing device to the 5-pin pug. Terminals (arranged from top to bottom) Terminal Voltage is on Condition Restriction Setting continuous voltage parallel to solenoid valve (O7) Rinse ... -
Page 27: Changing The Settings
Taking the machine out of service for a long period 16.3 Changing the settings Retrieving the settings Press the following buttons in turn: Enter "1575" (change the values with the buttons and confirm with the button) The setting (detergent) is displayed (number flashes). -
Page 28: Technical Data
Technical data 19 Technical data Voltage Total connection value see rating plate Fuse Minimum flow pressure Maximum inlet pressure 1 4.1 Water inlet temperature Dimensions *) Standard working height is 850 mm which can be optionally increased to 900 mm. The vertical dimensions are increased by 50 mm by this. - Page 30 Winterhalter Gastronom GmbH Winterhalter Gastronom GmbH Gewerbliche Spülsysteme Commercial Dishwashing Systems Winterhalterstraße 2–12 Winterhalterstraße 2–12 88074 Meckenbeuren 88074 Meckenbeuren Deutschland Germany Telefon +49 (0) 75 42/4 02-0 Telephone +49 (0) 75 42/4 02-0 Telefax +49 (0) 75 42/4 02-1 87...