Type Overview; Technical Data - AEG THYRO-S 1S*H 1 Series Operating Instructions Manual

9. Type overview

9.1 Type 1S...H 1
Thyristor switches with incorporated semiconductor fuse and system
bus interface.
Type capacity [kW]
Current 230V 400V 500V Dissi-
Type
1S
pation
H 1 16 3.7 6.4 8
H 1 30 6.9 12 15
H 1 45 10 18 22.5
H 1 60 14 24 30
H 1 100 23 40 50 105
H 1 130 30 52 65 150
H 1 170 39 68 85 210
HF 1 280 64 112 140 330
9.2 Type 1S...H RL1
Thyristor switches with incorporated semiconductor, system bus in-
terface, additional 24V d.c./a.c. control voltage supply, relay indica-
tion and load current monitoring
Type capacity [kW]
Type
Current 230V 400V 500V
1S
pation
H RL 1 16 3,7 6,4 8
H RL 1 30 6,9 12 15
H RL 1 45 10 18 22,5
H RL 1 60 14 24 30
H RL 1 100 23 40 50
H RL 1 130 30 52 65
H RL 1 170 39 68 85
HF RL 1 280 64 112 140
Dimensions in mm / kg
W H E
Weight Dim. Fuse
draw F1
[W]
30 45 131 127 0.7 851 20
47 45 131 127 0.7 851 40
48 52 190 182 1.7 853 63
80 52 190 182 1.7 853 80
75 190 190 1.9 854 200
125 320 241 4 856 200
125 320 241 4 856 315
125 370 241 5 858 350
Dimensions in mm / kg
Dissi- W H D Weight Dim. Current
Fuse
draw transf.
F1
[W]
30 45 131 127 0,7 851 40 20
47 45 131 127 0,7 851 40 40
48 52 190 182 1,7 853 100 63
80 52 190 182 1,7 853 100 80
105 75 190 190 1,9 854 100 200
150 125 320 241 4 856 150 200
210 125 320 241 4 856 200 315
330 125 370 241 5 856 300 350
84

10. Technical data

Type voltage
S..H1 230 Volt, 400 Volt, 500 Volt
– 57 % + 10 %;
S..HRL1 230 Volt – 15 % + 10 %;
> 99 V with additional 24 AC/DC elektronic power
400 Volt – 15 % + 10 %;
> 172 V with additional 24 AC/DC elektronic power
500 Volt – 15 % + 10 %;
> 215 V with additional 24 AC/DC elektronic power
Mains frequency all models 47Hz to 63Hz; i = 6Hz;
max. frequency change 5% per half wave
Load description ohmic load
Operating modes Name Load signal, with digital set point = ON
1:1 all full wave (default setting)
1:2 every 2. mains full wave (DC free)
1:3 every 3. mains full wave (DC free)
1:5 every 4. mains full wave (DC free)
Digital set points inputs (connection signals)
The Thyro-S has 2 set point inputs. The set point inputs
are safely disconnected from the mains (SELV, PELV).
Set point 1: Logic input 0-24V R
Set point 2: System interface, connection from superset
automation system via optional bus modu-
le.
Relay outputs using type 1S...H RL1
Changer, contact material: AgSnO2 / Au plated
The relay can be used for low load circuits (> 5V 20mA), however not
if it has been pre-loaded by 230V AC.
Maxiumum values: 250V 6A, 180W, 1500VA
Insulation strength 4kV / 8mm
3.3k h ON > 3V
>
i
85
EN