Setting The Handset'sringer Tone/Volume; Turning The Base's Ringer On/Off; Setting Auto Talk - Radio Shack 900 MHz Digital Spread Spectrum Cordless Phone with Digital Answerer and Caller ID/Call Waiting Deluxe Owner's Manual

If the dial tone stops, you have touch-tone
service. If the dial tone continues, you have
pulse service.
To set the dial mode, press
the phone if necessary, then hold down
until the phone beeps and the current
FLASH
dialing mode, tone or pulse, appears. Then
press # to set pulse mode or
mode. The phone beeps and displays
:_Wb_d] :_Wb_d] :_Wb_d] :_Wb_d] Jed[ý:_Wb_d] Jed[ý:_Wb_d] Jed[ý:_Wb_d] Jed[ý:_Wb_d]
or , then the display clears.
Note: The phone exits setting mode if a call
or page is received, or if you press
If the battery pack power gets too low, the
dial mode might reset to tone. If you are on a
pulse line and cannot make a call, try setting
the dialing mode to pulse.
SETTING THE HANDSET'S
RINGER TONE/VOLUME
You can select one of four different ringer
tone/volume settings on the handset. At any
time, except during a call, repeatedly press
8 8 8 8 9 9 9 9
or to select the desired ringer
VOL/CID
setting. Each time you press a button, the
phone rings at the selected setting and
7ý>_]^ 7ý>_]^ 7ý>_]^ 7ý>_]^ H_d][hý7ýBem H_d][hý7ýBem H_d][hý7ýBem H_d][hý7ýBem H_d][hý8ý>_]^ H_d][hý8ý>_]^ H_d][hý8ý>_]^ H_d][hý8ý>_]^
, ,
Bem Bem
Bem Bem
appears.
You can also turn off the ringer. At any time,
except during a call, hold down
until the phone beeps and
When you place the handset faceup on the
2H_d][hýE\\4 2H_d][hýE\\4 2H_d][hýE\\4 2H_d][hýE\\4
base, appears.
You can still make or receive a call even
when the ringer is turned off. When you have
an incoming call, any other phone connected
to the same line rings, and
pears on the handset's display.
To turn the ringer back on, simply press
8 8 8 8 9 9 9 9
or . The ringer is restored at the
CID
RINGER A HIGH setting.
12
TURNING THE BASE'S
RINGER ON/OFF
You can set the base's ringer to high or low,
to hang up
TALK
or turn it off. At any time, except during a call,
press
button, the phone rings at the selected set-
ting (or does not ring at the OFF setting). The
to set tone
display shows
Fkbi[ Fkbi[
Fkbi[ Fkbi[
ringer to off, the RINGER OFF indicator
lights.
Even when you turn off the base's ringer, you
TALK .
can still make or receive calls using this
phone. Telephones on the same line (and
the handset if it is away from the base and its
ringer is turned on) still ring when there is an
incoming call.
You can also set the ringer in the menu set-
ting mode (see "Using the Menu Button" on
Page 23).
1. Press
2. Press
H_d][h H_d][h H_d][h H_d][h
H_d][hý8 H_d][hý8 H_d][hý8 H_d][hý8
, or
3. Press
9 9 9 9
VOL/CID
4. Press
H_d][hýE\\ H_d][hýE\\ H_d][hýE\\ H_d][hýE\\
appears.
5. Press

SETTING AUTO TALK

Your phone is preset with Auto Talk off, so
?dYec_d]ý9Wbb ?dYec_d]ý9Wbb
?dYec_d]ý9Wbb ?dYec_d]ý9Wbb
ap-
you must press
Auto Talk turned on, you can answer a call
by lifting the handset from the base or, if the
VOL/
handset is away from the base, by pressing
any key.
Installation
. Each time you press the
SET/RING
>_ >_ >_ >_ Be Be Be Be E E E E \ \ \ \
, , or . When you set the
four times. The phone
MENU
announces "Ringer volume" followed by
its current setting. The display also
shows the current setting.
to enter the setting
SET/RING
mode.
or
SKIP REPEAT
setting.
to store the setting.
SET/RING
to exit the menu setting
STOP
mode.
to answer a call. With
TALK
to change the