Siemens GH180 Operating Instructions Manual page 6

Table of contents
3.1.6.16 Cabinet illumination and service socket in trigger and control section (option L50)...............47
3.1.6.17 Cabinet anti-condensation heating, temperature-monitored (option L55)..............................48
3.1.6.18 2 x 2 thermistor protection relays for alarms and faults (option L81).....................................48
3.1.6.19 3 x 2 thermistor protection relays for alarms and faults (option L82).....................................48
3.1.6.20 2 Pt100 evaluation units with 3 inputs each (option L91).......................................................49
3.1.6.21 Pt100 evaluation unit with 6 inputs and 2 analog outputs (option L93)..................................49
3.1.6.22 Pt100 evaluation unit with 6 inputs for ex-proof motors and6 analog outputs(option L95)
...............................................................................................................................................49
3.1.6.23 Mechanical safety locking system - Castell (option M10)......................................................50
3.1.6.24 Gland plates (option M35)......................................................................................................50
3.1.6.25 Gland plates (option M36)......................................................................................................51
3.1.6.26 Gland plates (option M37)......................................................................................................51
3.1.6.27 IP42 degree of protection (option M42)..................................................................................51
3.1.6.28 Redundant fan (Option M61).................................................................................................51
3.1.6.29 Drive prepared for duct flange connection in front (M64).......................................................51
3.1.6.30 Harsh environment conditions (M67).....................................................................................52
3.1.6.31 Drive prepared for duct flange connection in rear (M68)........................................................52
3.1.6.32 Extended space for bottom cable entry (Option M69)............................................................53
3.1.6.33 Controlled outgoing circuit for auxiliary equipment 400 V 3 AC or 460/480 V 3 AC (option
N30).......................................................................................................................................53
3.1.6.34 Controlled outgoing circuit for auxiliary equipment 400 V 3 AC or 460/480 V 3 AC (option
N31).......................................................................................................................................54
3.1.6.35 Controlled outgoing circuit for auxiliary equipment 400 V 3 AC or 460/480 V 3 AC (option
N32).......................................................................................................................................55
3.1.6.36 Controlled outgoing circuit for auxiliary equipment 400 V 3 AC or 460/480 V 3 AC (option
N33).......................................................................................................................................56
3.1.6.37 Controlled outgoing circuit for auxiliary equipment 230 V 1 AC or 120 V 1 AC (option
N35).......................................................................................................................................56
3.1.6.38 Controlled outgoing circuit for auxiliary equipment 230 V 1 AC or 120 V 1 AC (option
N36).......................................................................................................................................57
3.1.6.39 Controlled outgoing circuit for auxiliary equipment 230 V 1 AC or 120 V 1 AC (option
N37).......................................................................................................................................58
3.1.6.40 Controlled outgoing circuit for auxiliary equipment 230 V 1 AC or 120 V 1 AC (option
N38).......................................................................................................................................58
3.1.6.41 Motor-side grounding switch (option N45).............................................................................59
3.1.6.42 Power supply for auxiliaries 24 V DC/2.5 A (option N75).......................................................59
3.1.6.43 Cell Bypass (option U11).......................................................................................................59
3.1.6.44 Individual redundant cell (option U12)....................................................................................59
3.1.6.45 Redundant cell rank (option U13)..........................................................................................60
3.1.6.46 Sinusodial filter (option Y15)..................................................................................................60
4 Preparing for Use.......................................................................................................................................61
4.1 Requirements for installation location....................................................................................61
4.2 Checking on delivery..............................................................................................................62
4.3 The purpose of shock and tilt indicators.................................................................................63
4.4 Monitoring the Transport........................................................................................................64
4.5 Transportation........................................................................................................................67
4.5.1 Transporting the cabinet units................................................................................................67
4.5.2 Transporting the cabinet units................................................................................................68
4.5.3 Transport Using a Crane........................................................................................................69
6
SINAMICS PERFECT HARMONY GH180 6SR41 manufactured in NMA Nuernberg, Germany
Operating Instructions Rev.201706301306