XR-D400SL Safety precautions 1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer.
PC drive. In the SCSI mode, the XR-D400SL can be used as a CD-R/RW drive for a PC by connecting it through the SCSI interface. However, it is not possible to use the source disc tray as the dubbing source.
Page 4
XR-D400SL SCMS and RID functions The XR-D400 incorporates the SCMS (Serial Copy Management System) and the RID (Recorder Unique Identifier) functions. SCMS is used to limit digital copies to one generation only. The principles are shown in Fig. 3. With RID, the RID codes are written into discs which are as specified in the Orange Book Parts II and III. The codes contain the manufacturer's name, product name and machine number to enable the tracing of illegal copies.
Page 5
XR-D400SL Recording method of the CD-R/RW As shown in Fig. 6, the recording areas of a CD-ROM and a CD-R/RW are different. These discs use two recording areas in addition to the areas used for data recording by ordinary CD discs.
XR-D400SL Disassembly method Removing the top cover (Figs. 1 & 2) 1. Remove the 4 screws A from both sides of the top cover. 2. Remove the 4 screws B from the rear of the top cover, then remove the stop cover.
Page 7
XR-D400SL Removing the CD-ROM and CD-R/RW drives (Figs. 4, 5 and 7) 1. Remove the top cover. 2. Remove the rear panel. 3. Unplug the connectors from the drives (CD-ROM drive: power supply connector and control cable connector. CD-R/RW drive: power supply connector, control cable connector and audio signal connector).
Page 8
XR-D400SL Removing the front board (Fig. 13) 1. Remove the top cover. 2. Remove the front panel. 3. Remove the 13 screws J retaining the board. Fig. 13 Removing the disc (Fig. 14) 1. Remove the top cover. 2. Remove the front panel.
XR-D400SL Troubleshooting (For repairing the audio CD dubbing) POWER button Check the CN991 and S1034 on the Front board. Go to the "Power Does the POWER Are the pins of the CN991 Supply Operation". indicator light? on the Front board short-circuited...
Page 10
XR-D400SL Power supply operation First remove the 4 wires connected to the Power Supply unit (QAL0244-002) (see photo below) to do a check of the stand-alone mode. (1) Press the POWER button to ON, and check the voltages at the leftmost wire (red, DC +5 V) and the rightmost wire (yellow, DC +12 V).
Page 11
XR-D400SL Reproduction operation Insert a disc. Check the connections of the CN602, CN603 and Can the TOC be read? drives. Check the drives. Is playback possible? Check buttons. Applicable to REC/PLAY Check the CD-R/RW drive. disc tray only. Reproduction operation is OK.
Page 12
XR-D400SL Write operation The REC/PLAY disc tray (CD-R/RW drive) is composed of the mechanism unit (HXL-3BSPA) and the board ass'y (HQA-030A). Therefore, in case of a write failure, check the following points first before proceeding to the next step. The trouble is not due to the disc defect.
Page 13
Precaution for servicing Handling of board ass'y in REC/PLAY disc tray After replacing the board ass'y (HAQ-030A), be sure to modify it for use with the XR-D400SL by performing the following operations: 1. Remove 3 condensers and confirm the jumper settings.
Page 14
(5) When the firmware software screen appears (Fig. 6), confirm that; [Fig. 5] the Vendor is JVC, the product is XR-W4424 and the Version is 1.00. Note) If another content than the above is displayed, restart the operation from step (2).
Page 15
XR-D400SL Connection to a PC Fig. 10 shows the connection diagram of the PC. The REC/PLAY disc tray can be set as the master according to the jumper setting. After setting, connect the REC/PLAY disc tray to the secondary IDE cable.
Page 16
XR-D400SL VICTOR COMPANY OF JAPAN, LIMITED OPTICAL DISC BUSINESS DIV. PERSONAL & MOBILE NETWORK BUSINESS UNIT AV & MULTIMEDIA COMPANY 1644, Shimotsuruma, Yamato, Kanagawa 242-8514, Japan Printed in Japan No.A0001 200009 (S)
Page 17
XR-D400SL Block diagram CD-ROM DRIVE ASSY POWER SUPPLY ASSY QAL02335 QAL0244 100V POWER DC +12V(YELLOW) SUPPLY 4 PIN DC +5V(RED) ATAPI I/O 40 PIN 2 PIN CD-R/RW DRIVE ASSY CONTROL PCB ASSY FRONT PCB ASSY CN911 LOADER ASSY MAIN PCB ASSY...
Page 18
XR-D400SL Standerd schematic diagrams Front Key/Indicator circuit...
XR-D400SL PARTS LIST [ XR-D400SL ] Area suffix E ----------------- Germany - Contents - Exploded view of general assembly and parts list CR-R/RW mechanism assembly and parts list Packing materials and accessories parts list...
Page 25
XR-D400SL Exploded view of general assembly and parts list Block No. M1MM...
Page 26
XR-D400SL Parts list ( General Assembly ) Block No. Item Parts number Parts name Q'ty Description Area LE10227-001B F R O N T P A N E L LE30810-005A W I N D O W S C R E E N...
Page 27
XR-D400SL CD-R/RW mechanism assembly and parts list Block No. M2MM Parts list Block No. M2MM Item Parts number Parts name Q'ty Description Area HQ200031-001 U P P E R C A S E HQ200032-001 B O T T O M C O V E R...
Page 28
XR-D400SL Packing materials and accessories parts list Block No. M3MM Block No. M4MM Packing list Block No. M3MM Item Parts number Parts name Q'ty Description Area LE10236-001A P.CASE LE20509-001A P.PAD(L) LE20508-001A P . P A D ( U ) Q P C 0 5 0 0 6 5 1 5 P...