Setting Up; Setting Up Tv Channels Automatically; Setting Up Analogue Tv Channels Manually; Reducing Video Noise - Pioneer Kuro PDP-LX609A Operating Instructions Manual

08

Setting up

Chapter 8
Setting up

Setting up TV channels automatically

This section describes how to automatically search for and set up TV channels.
Using Auto Installation
When the flat screen TV is switched on for the first time after purchase, Auto
Installation menu appears on screen. For language, channel and time zone
selections, follow the steps below.
1 Select "Language" (/).
2 Select a language (/).
Language
Terrestrial Tuner
Time Zone
You can select from among four languages; English, Italian, Spanish and
Portuguese.
3 Select "Terrestrial Tuner" (/).
Use / to select "Digital", "Analogue" or "Both" (default).
4 Select "Time Zone" (/).
Use / to select "NSW/ACT" (default), "VIC", "QLD", "SA", "WA", "TAS" or "NT"
(see page 37).
5 Select "Start" (/ then ENTER).
Auto Installation automatically starts. To quit Auto Installation before it finishes,
press RETURN.
Note
• You can start Auto Installation from the HOME MENU after moving to another
city, for example. Follow the steps below before starting Auto Installation:
1 Press HOME MENU (/ then ENTER).
2 Select "Setup" (/ then ENTER).
3 Select "System Setup" (/ then ENTER).
4 Select "Auto Installation" (/ then ENTER).
The password entry screen appears. Enter your four-digit password using buttons
0 to 9. See Using a password
If no channel is found, check the antenna connections, and then retry Auto
Installation.
Note
• Channels obtained may vary depending on the installation environment and
weather conditions.

Setting up analogue TV channels manually

Use the Manual Adjust function to set up analogue TV channels manually.
1 Press HOME MENU.
2 Select "Setup" (/ then ENTER).
3 Select "System Setup" (/ then ENTER).
4 Select "Analogue TV Setup" (/ then ENTER).
The password entry screen appears. Enter your four-digit password using buttons
0 to 9. For the password, see Using a password on page 44.
26
En
: English
: Both
: NSW/ACT
Start
on page 44.
5 Select "Manual Adjust" (/ then ENTER).
Manual Adjust
Label
Sort
6 Select "Programme Entry" (/).
7 Select a programme number (/).
You can select 1 through 99.
8 Select "Search" (/).
9 Enter a frequency using buttons 0 to 9, then ENTER.
You can also press / to enter a frequency.
10 Select "Store" (/).
11 Select "Yes" or "No" (/).
Item Description
Yes You can select the channel using P+/P–
No You cannot select the channel using P+/P–
12 Press HOME MENU again to exit the menu.
Alternatively, to set up for another channel, repeat steps 7 to 11.
Note
• Manual Adjust also allows you to make selections for "Tuner NR" and
"Channel Lock". See Reducing video noise and Setting Channel Lock.

Reducing video noise

For the individual channels, you can specify whether the flat screen TV should
reduce video noise depending on the levels of broadcasting signals.
1 Repeat steps 1 to 5 provided for Setting up analogue TV channels manually .
2 Select "Tuner NR" (/).
3 Select "On" (/).
4 Press HOME MENU to exit the menu.
Note
• This function may not achieve a satisfactory result, depending on the
conditions of broadcasting signals.
• The factory default is "On".

Setting Channel Lock

Channel Lock inhibits selected TV channels from being tuned and watched.
1 Repeat steps 1 to 7 provided for Setting up analogue TV channels manually .
After selecting a channel (using Programme Entry), perform the following steps:
2 Select "Channel Lock" (/).
3 Select "Block" (/).
The selection is switched between "View" (default) and "Block".
4 Press HOME MENU to exit the menu.