Using Avc (Auto Volume Control); Using Sound Control; Optimum Performance; Power Control - Pioneer Kuro PDP-LX609A Operating Instructions Manual

Setting up

Using AVC (Auto Volume Control)

Reduces sudden volume change and compensates source sound level. To select
this option, follow the procedure below.
1 Repeat steps 1 to 3 provided for Sound adjustments.
2 Select "AVC" (/).
3 Select "On" (/).
4 Press HOME MENU to exit the menu.
Note
• To cancel this option, select "Off" in step 3.

Using Sound Control

Select this option when "OPTIMUM" is selected in the "AV Selection" menu for
optimum audio levels adjusted to the picture.
1 Press HOME MENU.
2 Select "Setup" (/ then ENTER).
3 Select "Picture" (/ then ENTER).
4 Select "AV Selection" (/ then ENTER).
5 Select "OPTIMUM" (/ then ENTER).
6 Press RETURN to return to the immediately previous menu.
7 Select "Sound Control" (/ then ENTER).
8 Select "On" (/ then ENTER).
9 Press HOME MENU again to exit the menu.
Note
• If "Sound Control" is set to "On" in the "Picture" menu, the "Sound" menu
options are unavailable except "AVC".
• This function is unavailable if any option other than "OPTIMUM" is selected.

OPTIMUM Performance

Select this option when "OPTIMUM" is selected in the "AV Selection" menu for
optimum picture quality. You can easily recognise the status of adjustments with
an on-screen bar graph monitor. For selection, follow the procedure below.
1 Repeat steps 1 to 6 provided for Using Sound Control.
2 Select "OPTIMUM Performance" (/ then ENTER).
The on-screen bar graph monitor appears.
OPTIMUM Performance [Analyser]
[OPTIMUM] On
Histogram
RGB
Room Light
OPTIMUM On/Off
Note
• OPTIMUM Performance compares the picture and sound quality between
"Off" (unadjusted) and "On" (adjusted using the TOOLS button).
• This function is unavailable if any option other than "OPTIMUM" is selected.
• When "OPTIMUM" is selected, press and hold p to display the OPTIMUM
Performance. Pressing p while displaying Teletext pages or subtitles does
not cause OPTIMUM Performance to appear.
• To cancel the OPTIMUM Performance, press EXIT.
• The OPTIMUM Performance is unavailable for a PC image.
[Picture] Contrast [Sound]
Brightness
Colour
Sharpness
60 1k 12k(Hz)
Colour Temp
Gamma

Power Control

Power Control provides convenient functions for power saving.

Energy Save

You may use one of the three Energy Save modes to save power consumption.
1 Press HOME MENU.
2 Select "Setup" (/ then ENTER).
3 Select "Power Control" (/ then ENTER).
4 Select "Energy Save" (/ then ENTER).
5 Select "Mode1", "Mode2" or "Off" (/ then ENTER).
Energy Save
Selections Off (default) Provides normally bright pictures
Mode1 Consumes less power than "Off" mode
Mode2 Consumes less power than "Mode1"
6 Press HOME MENU again to exit the menu.
Note
• When you change the Energy Save mode, you may notice a change in the
panel sound. This is normal.
• The Energy Save function can maintain efficiency of the screen for a long
period of time. Setting the Energy Save function to "Mode1" is recommended
in order to maintain the efficiency of the screen for a long period of time.
No Signal off (AV source only)
The system will be automatically placed into the standby mode if no signal is
received for 15 minutes.
1 Repeat steps 1 to 3 provided for Energy Save.
2 Select "No Signal off" (/ then ENTER).
3 Select "Enable" (/ then ENTER).

No Signal off

Selections Disable Does not place the system into the standby
(default) mode
Enable Places the system into the standby mode if no
signal is received for 15 minutes
4 Press HOME MENU to exit the menu.
Note
• Five minutes before the system is placed into the standby mode, a message
appears every minute.
• The system may not be placed into the standby mode when noise signals are
present at the flat screen TV after a TV programme finishes.
No Operation off (AV source only)
The system will be automatically placed into the standby mode when no operation
is performed for three hours.
1 Repeat steps 1 to 3 provided for Energy Save.
2 Select "No Operation off" (/ then ENTER).
3 Select "Enable" (/ then ENTER).

No Operation off

Selections Disable Does not place the system into the standby
(default) mode
Enable Places the system into the standby mode if no
operation is performed for three hours
4 Press HOME MENU to exit the menu.
08
33
En