First Steps; Opening The Box; Preliminary Inspection; Dhh805-A Start Up Procedures - ABB DHH805-A Operating Instruction

4 First steps

4.1 Opening the box

DHH805-A is delivered inside an hard plastic case containing:
— a carrying bag made of anti-static polyester with
removable and adjustable belt
— a pack of four type AA 1.5 V disposable alkaline batteries
for use in safe areas only (AA alkaline batteries not supplied)
— a sealed pack of rechargeable NiMH battery for use in
hazardous areas
— a universal AC power supply unit with four
interchangeable plugs (UK, USA, Europe and Australia)
— two standard banana jacks
— a USB cable to connect DHH805-A to the PC
— a leadset for transmitter connection (1,5 mt. / 5 ft)
— a CD-Rom / DVD-Rom containing PC-Tool installation
files, user's manual and HART
— an instruction sheet for DHH805-A PC connection
— a screwdriver

4.2 Preliminary inspection

Once opened the box, check the device for transport damage
and check the packaging material for accessories. Before
powering the DHH805-A on, it is necessary to remove the
rubber shell and install one of the battery packs provided by
tightening the screws located in the rear bottom of the Hand
Held Communicator.
1Battery fixing screws
Figure 2: DHH805-A rear view without rubber protective shell
Important. Please use the NiMH battery pack only when in
hazardous areas.
DD library
®
1

4.3 DHH805-A Start up procedures

To connect your DHH805 HART
DHH805 PC-Tool please follow the following instructions:
1. Install the DHH805 PC-Tool from the DVD-Rom you
have inside the device packaging: a driven installation
procedure starts and all the needed actions are explained
step by step.
Note.
Minimum system requirements for DHH805 PC-Tool software are:
Hardware:
— Intel Pentium® D 2,8 GHz or AMD Athlon™ 64 X2 4400+ processor
— Screen resolution of 1024x768 or greater
— Broadband Internet connection
— DVD-ROM reader
Software:
— Latest Windows XP, Windows 7 or Windows Vista Service Packs
— 1 gigabyte (GB) RAM (32-bit) for XP version or 1.5 gigabyte
(GB) RAM (32-bit) for Windows 7 and Windows Vista.
— 200 megabytes (MB) to 2 gigabytes (GB) available hard disk
space (32-bit)
— Microsoft NET Framework 3.5 or later
2. Unhook the elastic handle strap on the back of the device.
3. Remove the protective rubber shell from the strap
4. On the back of the device (see picture to left), release the
battery pack fixing screws from the holes located at the
bottom of the battery pack seat.
5. Install the rechargeable battery pack and tighten the fixing
screws.
6. By inserting the provided DVD now and running the
DHH805 Setup.exe, the DVD will walk you through steps
7-8, installing the program on your computer, and synching
the device to the program.
Note. Operation of the DHH805 is only allowed in safe areas.
7. In the black cardboard box inside the DHH805 suitcase,
you will find the battery charger and 4 power plug
adapters. Select the adapter that is compatible with your
AC power plug and snap it into place on the AC power
connection.
8. Open the plastic cover found on the top side of the
DHH805 and plug in the power cord of the battery
charger and connect the hand terminal to the PC via the
USB cable. After a few seconds, the backlight will come
on indicating that the DHH805 has turned on.
9. A short message will be displayed on DHH805. Depress
the bottom right-hand corner navigation key (On) and
access the activation menu.
Handheld communicator Model DHH805-A | OI/DHH805-EN Rev. D 9
4 First step
Hand Held Terminal to the
®