Page 2
Thank you for choosing a DOMUSA TEKNIK product. From the range of DOMUSA TEKNIK products you have chosen the Sanit model, a stainless steel hot water tank for producing domestic hot water (DHW) by means of a coil, which together with a DOMUSA TEKNIK heating boiler will provide the ideal level of comfort for your home, provided it is accompanied by a suitable hydraulic installation.
6 DIAGRAM AND ELECTRICAL CONNECTION..........................13 6.1 E ......................................13 LECTRICAL DIAGRAM 6.2 E ................................14 LECTRICAL CONNECTION TO THE BOILER 6.3 D DOMUSA TEKNIK :......................... 14 IAGRAMS FOR CONNECTION TO BOILERS 6.4 I SANIT :..........14 NSTRUCTIONS FOR ELECTRICAL CONNECTION OF THE STORAGE HEATER TO THE FOLLOWING BOILERS 7 MAINTENANCE ....................................16...
The anti-freeze used must be compatible with public health regulations and it must not be toxic. DOMUSA TEKNIK recommends the use of propylene glycol, consulting the product manufacturer before use.
Sanit 3 CONTROL COMPONENTS 1. Adjustment thermostat: 3. Thermometer: This control is for adjusting the desired This indicates the temperature of the hot water temperature of the hot water stored in the stored in the tank. tank. 2. Element switch: This is for starting up and stopping the optional back-up element of the hot water tank.
4 INSTALLATION INSTRUCTIONS The Sanit range of hot water tanks has been specially designed for installation and hydraulic connection to a wide range of heating boilers. 4.1 Connection The diagram below shows an example of the installation of Sanit hot water tanks with a heating boiler: 4.2 Equipment: 1.- Feed pump.
As an option DOMUSA TEKNIK supplies electronic cathodic protection that is suitable for the Sanit V inter-accumulator range. To install it, read carefully the assembly instructions that are provided with the same.
DOMUSA TEKNIK therefore optionally offers this DHW compensation tank for the Sanit 300, 500, 750 and 1000 models. To install the tank, carefully read the assembly instructions supplied with it.
DHW pressure of 0,7 MPa (7 bar). To prevent this pressure from being exceeded, DOMUSA TEKNIK recommends fitting a safety valve to the DHW circuit, calibrated to a maximum of 0,7 MPa (7 bar). The safety valve will always discharge into a drain.
If the tank is connected to a DOMUSA TEKNIK brand heating boiler, the boiler will be equipped with a summer or winter position switch, which is used to choose between: ☼...
Sanit 6.2 Electrical connection to the boiler The electrical connection between Sanit hot water tanks and DOMUSA TEKNIK heating boilers is made by simply connecting the tube shown in the electrical diagram, i.e. the T tube. Connect the tube to the side of the hot water tank as shown in the electrical diagram in section 5.1.
Page 17
The correct process for the electrical connection of the SANIT hot water storage heater to these boilers is as follows: - Connect the hot water temperature sensor (supplied optionally) to the sensor connector block J3 on the boiler (terminals 13 and 14). To do this, first remove the element (Ra) supplied with it (see "Connection Diagram").
8 START-UP For the guarantee to be valid, the hot water tank must be started up by an Official DOMUSA TEKNIK Technical Assistance Service. Before starting it up, the following must be ensured: - The electrical connection of the hot water tank is correctly made.
10 DRAINING THE TANK To drain the tank Sanit 300/500/750/1000, remove the brass plug, then connect a hose to the drain socket on the botton of the tank. Check the hose is correctly connected to the tank drain socket. Run the hose to a nearby floor drain. This must be at a lower level than the tank. Begin the suction process so that the water begins to flow, and wait until it drains completely.
Sanit 11 SPARES LIST 11.1 Hot water tank SANIT 300 Pos. Code Name Pos. Code Name CFER000085 ¾” black embellisher CACU000038 Bridge cover CFER000082 ¾” tapered plug CFOL000037 Brass plug GELESAN008 Electrical board MVAR010027 Seal CFER000086 1” black embellisher CFER000008 1”...
Electrical board Pos. Code Name Pos. Code Name CELC000099 Knob CELC000007 Control thermostat CACU000035 Control panel CACU000036 Control panel cover CELC000136 Thermometer CACU000037 Control panel plug CELC000025 Switch...
Sanit 13 TECHNICAL CHARACTERISTICS Sanit Sanit MODEL Sanit 300 Sanit 500 Sanit 750 1000 1000 SBH Characteristics Installation Floor Total volume 1000 1000 Max. Storage temperature ºC Max. working pressure of hot water tank Max. primary temperature ºC Max. primary working pressure...
2 Years for electric and hydraulic elements: pumps, valves, etc. 5 Years for domestic hot water tanks. For a period of 2 years from the start-up date, DOMUSA TEKNIK will carry out any repairs of original flaws or defects totally free of charge.
Page 32
Bº San Esteban s/n Ellesmere Port, CH65 9BF 20737 ERREZIL (Gipuzkoa) Tel: 0151 909 6222 Tel: (+34) 943 813 899 www.domusateknik.com DOMUSA TEKNIK reserves the right to make modifications of any kind to its product *CDOC000222* characteristics without prior notice. CDOC000222 07/16...
Need help?
Do you have a question about the SANIT 300 and is the answer not in the manual?
Questions and answers