Advertisement
Quick Links
Hardware List
Ref.
Qty.
Part No.
AA
2
SC1048B
BB
1
030-1217
CC
1
030-1129
DD
2
012-0761
EE
8
030-0402
FF
10
030-0307
GG
10
030-0411
HH
6
030-0306
II
2
030-1340
JJ
2
030-0043
KK
4
030-0713
LL
4
030-0865
MM
2
030-0354
1
030-0353
1
030-0397
1
HK1020
1
030-1237
1
030-1352
1
044-2124
CAUTION: This mount is intended to support a flat monitor having a diagonal screen size of 32-50", a
weight of 170 lbs and having a monitor mounting hole pattern no larger than 700mm wide by 400mm
high. For added safety and ease of installation, use a qualified professional to properly install the correct
mounting hardware. Bretford will not be liable for the improper use or installation of its products.
**MOUNTING YOUR MONITOR
Bretford has tried to provide courtesy M4, M5 and M6 metric hardware to accommodate as many
styles of large monitors as possible. New monitor designs are constantly entering the market and your
monitor may require a metric hardware size not included with this model. Your local small hardware store
is usually the most effective place to source additional metric screws. If you are unsure of the hardware
size, please consult your monitor manufacturer for the appropriate wall mounting hardware size for your
monitor. NOTE: The minimum thread engagement required is the same as the diameter of the screw, for
instance, if the screw diameter is 8mm, the minimum thread engagement is also 8mm.
WARNING
The monitor bracket screws must be fully seated in the back of the monitor in order to create a
stable installation. If the monitor bracket screws are not fully seated, your installation will not be stable
and personal injury or damage to your monitor may result.
When mounting monitor brackets, do not use screws that exceed the depth of the monitor mounting
holes. Using screws that are too long may cause damage to your monitor. Never tighten fasteners past
the first sign of resistance. Over tightening may cause serious damage to your monitor. Any doubt, the
installer should consult monitor manufacturer for mounting hole depth guidelines.
FPPC72V200
72" FREE STANDING
DISPLAY CART
Assembly Instructions
Description
1/4-20 45mm Joint Connector Bolts
1 3/4" Diameter Washer
5/8-11 UNC 1 3/4" Socket Hd Screw
Cable Clips
#10-32 x 5/8" Combo Screws
5/16-18 x 5/8" Hex Hd Screws
5/16-18 Serrated Nuts
1" x 21/64" x 1/16" Washers
1/4-20 x 2" Hex Hd Bolts
#10-1/4" Washers
3/8-16 x 5/8" Button Cap Screws
#6 x 1/2" Button Pin-In Hd Screws
10-32 x 1 1/2" Button Socket Screws
1/8" T-Handle Allen Wrench
3/16" Allen Wrench
5/32" Allen Wrench
1/2" Allen Wrench
1/8" Security Pin-In Driver Bit
Courtesy Monitor Hardware Pack
1
Advertisement
Related Manuals for Bretford FPPC72V200
Summary of Contents for Bretford FPPC72V200
- Page 1 170 lbs and having a monitor mounting hole pattern no larger than 700mm wide by 400mm high. For added safety and ease of installation, use a qualified professional to properly install the correct mounting hardware. Bretford will not be liable for the improper use or installation of its products. **MOUNTING YOUR MONITOR Bretford has tried to provide courtesy M4, M5 and M6 metric hardware to accommodate as many styles of large monitors as possible.
- Page 2 STEP 1 If necessary, loosen bolts and slide bracket up or down to align with the pole. Slide pole onto cart as shown. NOTE: Make sure pole sits completely on bottom shelf. Secure pole to cart bracket with screws (AA) as shown. (Use 5/32”...
- Page 3 Flange in front of rack rail STEP 2 Install each utility shelf to rack rail as shown using screws (EE). Make sure shelf flange is in front of rack rail. Shelves may be install at your own desired locations within the rails.
- Page 4 STEP 3 Attach the box swivel to the nugget with screws (FF) and nuts (GG) as shown. STEP 4 Attach main support to swivel bracket with screws (FF), washers (HH) and nuts (GG) as shown.
-
Page 5: Tilt Adjustments
TILT ADJUSTMENTS NO TILT IN THIS LOCATION 7.5 DEGREE TILT IN THIS LOCATION 15 DEGREE TILT IN THIS LOCATION FIGURE 3 STEP 5 Loosely insert the lower spike/box assembly screws (KK) then fit the spike/box assembly notch over the screws and insert the tilt adjustment screws (KK) at the angle desired and tighten all screws. This assembly can be installed with or without a tilt. - Page 6 Measure the distance from the center of mount holes to the top of the monitor. FIGURE 4 FIGURE 6 FIGURE 5 STEP 6 Roughly measure the distance from the center of monitor mounting holes to the top of the monitor (FIGURE 4). Round to the highest inch and from the top of the pole, use that measurement as a guide to the location for the top nugget screw on the pole.
- Page 7 BOTTOM STEP 7 Attach both hook bars onto the back of your monitor using the mounting holes built into the case. A courtesy hardware pack has been provided with several metric screw sizes. You may need to purchase additional metric screws from your local hardware store for odd shaped monitors. CHANGING MONITOR HEIGHT MONITOR NOT SHOWN (IF NECESSARY)
- Page 8 STEP 9 Attach the stop brackets to the hook bars as shown with security screws (LL) using the driver bit provided. CENTER MONITOR HORIZONTALLY THEN SECURE STEP 10 Center your monitor horizontally and then tighten in place with screws (MM).
- Page 9 STEP 11 Snap pole cap onto the top of the pole as shown. STEP 12 Feed your power cord into beam then snap each plastic clip inside beam to trap and contain power cord. Part # 031-7558 Rev. 11.05.07 CZ...
Need help?
Do you have a question about the FPPC72V200 and is the answer not in the manual?
Questions and answers