Model: Clss Integrity Series - Life Fitness ATV15-XXXA-02 Assembly Instructions Manual

Model: CLSS (Integrity Series)
Tools Required: Standard Screwdriver, Phillips Screwdriver, Torx Head Screwdriver, Side Cutters, Hex Head Wrench
Note: The following Assembly Instructions show the CONSOLE attached prior to ATTACHABLE TV installation.
Follow all appropriate steps when the console is not mounted.
1. Remove the square END CAP (a) and two PLASTIC PLUGS (b) located
behind the console on the MAIN CONSOLE SUPPORT TUBE (c).
2. Remove the four SCREWS (d) that are used to fasten the console. Care-
fully set the console aside, securing it so that it does not fall.
3. Locate the TV MOUNTING BRACKET (e). Unwrap the POWER SUPPLY
CORD (cc) and COAXIAL CABLE (dd) located within the CONSOLE
SUPPORT BRACKET TUBE (c). Route these cables through the opening of
the TV MOUNTING BRACKET (e).
Locate the AUDIO / VIDEO / I-R REMOTE CONTROL CABLE ASSEMBLY
(f). Route this cable assembly through the TV MOUNTING BRACKET (e)
with the 2-connector end coming out of the opening of the TV MOUNT-
ING BRACKET.
4. Insert the TV MOUNTING BRACKET into the CONSOLE SUPPORT TUBE
and fasten with three SCREWS (h) and three WASHERS (i).
CAUTION: Do not pinch any cables when inserting the TV MOUNTING BRACKET into the CONSOLE SUPPORT TUBE.
5. Assemble the HINGED BRACKET (j) to the TV MOUNTING BRACKET with the following provided hardware:
k. screw
l. steel washer
m. nylon plastic washer
n. nylon plastic shoulder washer
o. steel washer
p. nut
j
p
o
n
m
l
k
h
i
58
a
b
c
d
e
cc
dd
f
f
g
6. Assemble the MATING BRACKET (q) to the back of the
ATTACHABLE TV (bb) with four SCREWS (r) and four steel
WASHERS (s).
7. Assemble the ATTACHABLE TV (bb) to the TV MOUNTING
BRACKET. Insert one HEX BOLT (t) and WASHER (u) through
both parts that make up the hinged bracket. Partially tighten
both brackets with one LOCKNUT (v). Adjust the TV position
so that the TV face is perpendicular to the floor. Insert two
SCREWS (w) to lock the bracket position. Fasten the hinged
bracket securely.
8. Insert one end of the AUDIO / VIDEO / I-R REMOTE CON-
TROL CABLE ASSEMBLY into the CONSOLE CONNECTOR.
Attach the FERRITE to the main CONSOLE CONNECTOR
(See "g" on previous page). Attach the CABLE TIE below the
FERRITE to prevent the FERRITE from sliding down the cable
after the FERRITE is placed into the MAIN CONSOLE
SUPPORT CABLE ACCESS HOLE.
9. Reattach the console to the console support bracket with the four previously removed screws in Step 2.
Connect the COAXIAL CABLE, POWER CORD, and AUDIO / VIDEO / I-R REMOTE CONTROL CABLE ASSEMBLY
to the rear of the ATTACHABLE TV. See the Media Connections pages in this manual for detailed information.
10. Re-insert the previously removed square END CAP (a) into the top of the TV MOUNTING BRACKET.
11. Secure the POWER ADAPTER (x) to the FRONT STABILIZER (y) using two CABLE TIES (z) as shown. Be sure the
CABLE TIES are pulled tight and trim the excess CABLE TIES. Connect the screw-type connector of the POWER
SUPPLY CORD (aa) to the underside receptacle. Bundle excess power cord and store under the unit.
Connect the COAXIAL CABLE (f) to the broadcast supply cable in similar fashion.
12. Connect the POWER SUPPLY CORD to the POWER ADAPTER (x).
13. Continue with the remainder of assembly as instructed in the Assembly Instructions. Plug the POWER SUPPLY
CORD into an electrical outlet upon completion.
y
z
s
r
w
v
u
f
x
aa
bb
q
t
59