Models: Clst & 97T Integrity Series - Life Fitness ATV15-XXXA-02 Assembly Instructions Manual

12. Connect all cables to their corresponding jacks located
on the bottom of the TV (16). Re move the tape from the
end of the MEDIA CABLES (Power, Coaxial, I-R Remote
Control, Video).
See the Media Connections pages in this manual for
detailed information. Feed any excess media cable into
the MAIN BRACKET (4).
13. Install the TOP MAIN BRACKET CAP (21) to the top of the
MAIN BRACKET ASSEMBLY (4).
14. Replace the REAR CONSOLE COVER (10) and secure it
using the previously removed two SCREWS (9). Tighten
the screws securely (8-10 ft. lbs.). Do not overtighten the
screws.
15. Slide the BRACKET COVER (7) down to meet the REAR
CONSOLE COVER (10). Snap the BRACKET COVER into
the REAR CONSOLE COVER.
16. Align the lowest side holes on the TV BRACKETS (8 &15).
Secure the TV BRACKET into proper position using one SCREW (22) on each side.
17. Plug in the treadmill and power on the treadmill and TV. Refer to the ATTACHABLE Operation Manual for proper TV
setup.
22
4
14
21
15
18
19
22
4 8 20
7
10
8
16
Models: CLST & 97T (Integrity Series)
Tools Required: Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters
Note: Proceed with the following steps immediately after attaching the DISPLAY CONSOLE as described in the
16
Integrity Series Assembly Instructions. Do not install the ACCESSORY TRAYS.
1. Insert one end of the AUDIO / VIDEO / I-R CABLE ASSEMBLY (a) into the console connector. Route the other end
through the HOLE (a1) on the right upright and through the GROMMET (a2). Continue routing the cable assembly
through the hole of the TV MOUNTING BRACKET END CAP (a3), through the TV MOUNTING BRACKET TUBE
(g), and exiting through the CENTER HOLE (a4) of the TV MOUNTING BRACKET TUBE (g).
2. Route the POWER SUPPLY CORD (b) and COAXIAL CABLE (c) through the left upright, out the HOLE (b1) on the
left upright and through the GROMMET (b2). Route the cable through the hole of the TV MOUNTING
BRACKET END CAP (b3), through the TV MOUNTING BRACKET TUBE (g), and exiting through the CENTER HOLE
(a4) of the TV MOUNTING BRACKET TUBE (g). Install a GROMMET (a5) onto the CENTER HOLE (a4).
a4
a5
b3
3. If through-holes in the four CONSOLE BOSSES (d) are not present, use a 5/16" drill from the top center of the four
console bosses to create through-holes. Note: Be careful not to damage the threads of the brass inserts when
drilling the through-holes in the CONSOLE BOSSES (d).
CAUTION: Wear eye safety equipment when drilling the through-holes in the console bosses.
4. Locate the four RETAINING SPACERS (e). Position the RETAINING SPACERS over the CONSOLE BOSSES (d) as
shown. Be sure the RETAINING SPACERS are fully nested over the structural ribs inside the REAR CONSOLE (f).
5. Position the BRACKET TUBE (g) with the TV MOUNTING BRACKET PLATE (j) facing upward. Position two SCREWS
(h) on either side through the CONSOLE BOSSES (d). Install four NYLOCK NUTS (i) onto the installed SCREWS (h)
securing the RETAINING SPACERS (e) and BRACKET TUBE (g) to the REAR CONSOLE. Tighten the NYLOCK NUTS
securely. Do not overtighten the NYLOCK NUTS.
g
h
g
a
b
c
a3
b1
b2
j
i
e
f
d
a1
a2
To console
connector
To console
connector
15