Model: Clsl Integrity Series - Life Fitness ATV15-XXXA-02 Assembly Instructions Manual

25. Secure the attachable TV (4) to the main bracket assembly
using the bolt (1) , washer (2), and nut (3).
26. Connect the cables to the attachable TV (4).
27. Align the lowest side holes on the TV brackets (3) and
main bracket assembly (2).
28. Secure the TV bracket (3) into position using one screw (1)
on each side of the TV bracket.
29. Connect the remote cable (1), high-def cable (2), and power cable (3) to the ports on the back of the console.
30. Reinstall the console.
56
Model: CLSL (Integrity Series)
Tools Required: Metric Hex Key Set, Side Cutters, T-45 Torx Wrench
1. Remove the CONSOLE SUPPORT TOP CAP (a).
2. Remove the two SCREWS (b) securing the CONSOLE
SUPPORT COVER (c). Remove the console support
cover and set it and the screws aside.
3. Remove the four SCREWS (d) securing the DISPLAY
CONSOLE (e). Set the SCREWS aside. Tilt the
CONSOLE forward and disconnect all cables. Set the
CONSOLE aside.
4. Locate the TV MOUNTING BRACKET (f). With the
mounting holes in the tube facing downward, slide
the tube portion of the mounting bracket into the
top of the CONSOLE SUPPORT (g). Align the inserts
in the tube with the mounting holes on the underside
of the console support. Secure the mounting bracket
using two SCREWS (h). Tighten the screws securely.
CAUTION: Do not pinch any cables when inserting the
MOUNTING BRACKET into the CONSOLE SUPPORT.
5. Re-install the DISPLAY CONSOLE (e) using the four previously removed SCREWS (d). Tighten the SCREWS to 6-8
in-lbs. Do not overtighten the SCREWS.
CAUTION: Do not pinch any wires when assembling the DISPLAY CONSOLE to the console support.
6. Attach the ADAPTER BRACKET (i) to the ATTACHABLE TV (j) using four SCREWS (k) and WASHERS (l). Tighten the
SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS.
Attach the ATTACHABLE TV with ADAPTER BRACKET to the UPPER MOUNTING PLATE (m) using four SCREWS (n),
SHOULDER NYLON WASHERS (o) and NYLON FLAT WASHER (p). Tighten the SCREWS to 6-8 in-lbs. Do not over-
tighten the SCREWS.
7. Connect the COAXIAL CABLE, POWER CORD and R EMOTE CABLE to the rear of the ATTACHABLE TV. See the
Media Connections pages in this manual for detailed information.
8. CABLE TIE (r) any excess cable together behind the ATTACHABLE TV and position the cables between the
MOUNTING BRACKET (f) and the DISPLAY CONSOLE (e).
9. Re-install the CONSOLE SUPPORT COVER (c) and secure it using the two previously removed SCREWS (b).
10. Locate the new TOP CAP (s). Place the new top cap into position at the top of the CONSOLE SUPPORT COVER (c).
Be sure the top cap snaps securely in place.
11. Secure the POWER ADAPTER (t) to the FRONT STABILIZER (u) using two CABLE TIES (r) as shown. Be sure the
cable ties are pulled tight. Trim the excess cable ties. Connect the SCREW-TYPE CONNECTOR of the POWER
CORD (aa) to the front side receptacle. Bundle excess power cord
and store under the unit. Connect the COAXIAL CABLE (bb) to the
broadcast supply cable in similar fashion.
12. Connect the POWER SUPPLY CORD to the POWER ADAPTER (t).
k
o
p
i l
j
m
e
f
g
c
h
d
t
bb
aa
r
u
n
s
a
b
57