AccuTemp Vision Touch Operator's Manual page 32

Combi steamer
Table of Contents

Advertisement

One Year – Labor & Parts after standard limited warranty expires - U.S. Only
LIMITED EXTENDED WARRANTY VISION/VISON TOUCH COMBI OVEN
AccuTemp Products, Inc. (AccuTemp) warrants that your AccuTemp Vision Combi Oven will be free of defects in material and
workmanship under normal use for an additional twelve (12) months from the end of the standard limited warranty
1.
It is the sole responsibility of the owner/operator/purchaser of this equipment to ensure that a one (1) year preventative
maintenance checklist is completed by an authorized service company. Non-compliance will potentially damage this equipment
and/or components and VOID the extended warranty. Proof of this compliance requirement being met is the completed one (1) year
Vision Combi – 12 Month Inspection and Extended Warranty Checklist. It must be emailed, faxed or mailed to AccuTemp within ten
(10) to twelve (12) months from installation to qualify for the extended warranty.
2.
It is the sole responsibility of the owner/operator/purchaser of this equipment to ensure that the incoming water supply to the
equipment meets the water quality requirements. Non-compliance will potentially damage this equipment and/or components and
VOID the extended warranty. Proof of this compliance requirement being met is an affirmative water sample test report for the
incoming water supply to the equipment, with the sample collected and submitted for testing by an authorized service company. It
must be emailed, faxed or mailed to AccuTemp within ten (10) to twelve (12) months from installation to qualify for the extended
warranty.
While AccuTemp products are built to comply with applicable standards for manufacturers, including Underwriters Laboratories (UL) and
Underwriters Laboratories Sanitation requirements, it is the responsibility of the owner/operator/purchaser and the installer to comply with
any applicable local codes that may exist.
AccuTemp should be contacted and advised of service issues, regardless of the warranty period. During the warranty period, AccuTemp
must be contacted for warranty service requests. AccuTemp agrees to repair or replace, at its option, F.O.B. factory, any part which
proves to be defective due to defects in material or workmanship, provided the equipment has not been altered in any way and has been
properly installed, maintained, and operated in accordance with the instructions in the AccuTemp Installation/Operators Manual.
During the warranty period AccuTemp also agrees to pay for any factory authorized equipment service agency within the continental
United States for reasonable labor required to repair or replace, at our option, F.O.B. factory, any part which proves to be defective due to
defects in materials or workmanship, provided the service agency has received advance approval from AccuTemp to perform the repair
or replacement. This warranty includes travel time not to exceed two hours and mileage not to exceed 50 miles (100 miles round trip)
during standard business hours, excluding overtime hours, holiday rates or any other additional fees.
Post start-up assistance or training, tightening of loose fittings, external electrical, plumbing and drain connections. Minor
Warranty Does Not Apply To:
adjustments and cleaning of any kind.
1.
Damage caused as the result of inadequate routine maintenance and cleaning. Routine maintenance and cleaning is the
responsibility of the commercial purchaser/user.
2.
Replacement of wear parts, including light bulbs, door gaskets and replacement of glass due to damage of any kind.
Equipment damage caused by shipping and handling, improper installation, accident or alteration of any kind.
3.
Any damage caused by failure to comply with the water quality requirements listed in this document.
4.
The use of cleaning and care products not recommended by AccuTemp.
5.
AccuTemp makes no other warranties or guarantees, whether expressed or implied, including any warranties of performance, merchantability,
6.
or fitness for any particular purpose. AccuTemp liability on any claim of any kind, including negligence, with respect to the goods and services
covered hereunder, shall in no case exceed the price of the goods and services, or parts thereof, which gives rise to the claim. In no event shall
AccuTemp be liable for special, incidental, or consequential damages, or damages in the nature of penalties.
This constitutes the entire warranty, which supersedes and excludes all other warranties, whether written, oral, or implied.
MP6931-1710
Water Quality Requirements
Inlet Pressure
Description
Free Chlorine
Total Chlorine
pH
Total Dissolved Solids
Water Hardness
Alkalinity (as CaC3)
Chlorides (Sulfate+Chloride+Nitrate)
Iron FE
Silica
40 – 80 psi
Value
< 0.1 ppm (mg/l)
< 0.1 ppm (mg/l)
7 - 8.5
< 150 ppm (mg/l)
< 90 ppm (mg/l)
< 60 ppm (mg/l)
< 40 ppm (mg/l)
< 0.1 ppm (mg/l)
< 13 ppm (mg/l)
32

Advertisement

Table of Contents
loading

Related Products for AccuTemp Vision Touch

Table of Contents