Pressure Setting; G20 Natural Gas @ 20 Mbar; G30 Butane @ 28-30 Mbar; G31 Propane @ 37 Mbar - STOVES 850DODL User & Installation Instructions Manual

Introduction

Thank you for choosing a British
built appliance by Stoves.
We hope that the following information
will help you to familiarise yourself
with the features of the appliance, and
to use it successfully and safely.
Our policy is one of constant
development and improvement. Strict
accuracy of illustrations and specifications
is not guaranteed. Modification to
design and materials may
necessary subsequent to publication.
This appliance must be installed in
accordance with the regulations in
force, and only in a well ventilated
space. Read the instructions before
installing or using this appliance.
Your 1st Year Guarantee
To fulfil the conditions of your guarantee,
this appliance must be correctly
installed and operated, in accordance
with these instructions, and only be
used for normal domestic purposes.
Please note that the guarantee, and
Service availability, only apply to the
UK and Republic of Ireland.
Before using the appliance for
the first time, remove any protective
polythene film and wash the oven
shelves and furniture in hot soapy
water, to remove their protective
coating of oil. Even so, when you first
turn on the oven or grill you may
notice a smell and some smoke.
Your new appliance is designed to be
installed free-standing or flush to
base units.
Gas & Electrical connection
Please refer to installation instructions
for the Gas & Electrical Safety Regulations
and the Ventilation Requirements.
In your own interest, and that of safety,
it is the law that all gas appliances be
be
installed by a competent person who
will ensure that the installation is in
accordance with "The Gas Safety
(Installation & Use) Regulations 1994", &
the "The Gas Safety (Installation & Use)
(Amendment) Regulations
Failure to comply
Regulations is a criminal offence.
Corgi registered installers undertake to
work to satisfactory standards.
Disconnection of gas and electric
appliances should always be carried
out by competent persons.
Warning: This appliance must be
earthed.
2
Connect to the gas supply
The inlet to the cooker is
internal situated at the rear right corner.
Fit the bayonet connection. This should
be located so as to ensure the flexible
connector hose does not kink.
Use a 900mm - 1125mm length of
flexible connector.
Ensure that all pipe work is of the correct
rating for both size and temperature.
Natural Gas - Flexible connections
should comply with BS 669. Parts of
the appliance likely to come into
contact with a flexible connector have
a temperature rise of less than 70˚C.
1996".
LP Gas - For flexible connections use
with these
a bayonet type hose, suitable for use
on LP Gas up to 50 mbar pressure rise
and 70˚C temperature rise. The flexi-
ble hose should be coloured black
with a red stripe, band or label. If in
doubt, contact your supplier.
After installation, make sure all
connections are gas sound.
Installation Instructions
Commissioning
" BSP
⁄
1
2
Burner aeration
All burners have fixed aeration and no
adjustment is possible.

Pressure setting

G20 Natural Gas @ 20 mbar

G30 Butane @ 28-30 mbar

G31 Propane @ 37 mbar

Pressure test point
Use the oven injector
Grill - Turn the top oven / grill control
knob to the
GRILL
before pressing the ignition switch or
holding a lighted match or taper to the
burner.
Hob - Turn the control knob to the
position, wait a second before
ON
pressing the ignition switch or holding
a lighted match or taper to the burner.
Ovens - Open the oven door. Turn
the control to the
press the ignition switch,or holding a
lighted match or taper to the burner. The
burner operates at a low rate for up to
60 seconds until the flame supervision
device opens and full gas rate is
obtained.
Before leaving the installation
1. Place all the loose parts of the
cooker into position.
2. Show the customer how to operate
the cooker and give them this
handbook. Thank you.
27
position, wait a second
FULL
position and
FULL ON