Page 1: User Manual
MTX-xG-JAVA-IoT Family MTX-3G-JAVA-IoT MTX-4G-JAVA-IoT User Manual www.mtxm2m.com 2017/07 v1.2 Page 1 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 2: General Notes
To contact customer support please use the contact details below: Matrix Electrónica Alejandro Sánchez, 109 28019 Madrid (SPAIN) gsmsupport@matrix.es Information about the MTX-IoT product and its accessories is available on the following web site: www.mtxm2m.com Or contact your local distributor / sales agent. www.mtxm2m.com 2017/07 v1.2 Page 2 MTX M2M®...
Page 3: Revision Information
MTX-xG-JAVA-IoT Family Revision information Revision Date Author Changes 2016/01 Initial release 2017/05 Approvals-RED 2017/07 Added LTE versions www.mtxm2m.com 2017/07 v1.2 Page 3 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 4 Models with RJ11 connector and/or analog audio ............30 1.9.4 All other models ......................31 1.10 Hardware revisions ........................ 32 Mechanical description ......................... 33 Overview..........................33 2.1.1 Models with 5-way plug-in 5.00mm pitch terminal block ..........33 www.mtxm2m.com 2017/07 v1.2 Page 4 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 5 RS232 interface ......................55 4.4.3 Analog inputs ......................... 56 4.4.4 Optoisolated I/O ......................57 4.4.5 Counter input ........................ 58 RS485 bus ..........................59 CAN bus and 1-Wire bus ......................60 www.mtxm2m.com 2017/07 v1.2 Page 5 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 6 AT command interpreter ....................... 78 Embedded applications ......................... 79 MTX-Tunnel software application ..................80 Safety and product care ........................ 82 Safety instructions ......................... 82 General precautions ......................82 SIM card precautions ......................83 www.mtxm2m.com 2017/07 v1.2 Page 6 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 7 Where to install the modem ....................85 9.1.1 Environmental conditions ..................... 85 9.1.2 Signal strength ....................... 85 9.1.3 Connections of components to MTX-IoT device ............85 9.1.4 Network and subscription ..................... 85 How to install the modem ..................... 86 9.2.1 Power supply ......................... 86 9.2.2...
Page 8 MTX-xG-JAVA-IoT Family Accessories ..........................104 Sales contact ..........................105 www.mtxm2m.com 2017/07 v1.2 Page 8 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 9: Introduction
The MTX-IoT devices can also be controlled via AT commands and standard interfaces such us USB 2.0 High Speed or RS232 with Linux and Windows® drivers. The MTX-IoT family is RoHS & WEEE compliant and it is manufactured following the ISO 9001 & IS0 14001 Quality certifications.
Page 10: Ordering Information
MTX-xG-JAVA-IoT Family 1.2 Ordering information MTX-3G-IoT-JAVA www.mtxm2m.com 2017/07 v1.2 Page 10 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 11: Mtx-4G-Iot-Java
MTX-xG-JAVA-IoT Family MTX-4G-IoT-JAVA www.mtxm2m.com 2017/07 v1.2 Page 11 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 12: Features By Model
*1 *1 *1 *1 *1 *1 *1 *1 Analog audio (A) *1 *1 *1 *1 Internal RF module *1 *1 *1 *1 *1 *1 *1 *1 *1: option. See incompatibility table www.mtxm2m.com 2017/07 v1.2 Page 12 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 13: Mtx-4G-Iot-Java
220VAC/6A Relay (P) *1 *1 *1 *1 I/O expansion (X) *1 *1 *1 *1 RJ11 power supply (J) *1 *1 *1 *1 Internal Wireless module *1 *1 *1 *1 www.mtxm2m.com 2017/07 v1.2 Page 13 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 14: Options Incompatibilities Table
X X X X X *3 Wireless module X *1 *1 *1 X: not compatible *1: all serial ports not available at the same time *2: ULP contains LP functionality *3: mandatory www.mtxm2m.com 2017/07 v1.2 Page 14 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 15: Mtx-4G-Iot-Java
X X X X X Internal Wireless module *1 *1 *1 X: not compatible *1: all serial ports not available at the same time *2: ULP contains LP functionality *3: mandatory www.mtxm2m.com 2017/07 v1.2 Page 15 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 16: Highlights
Operating temperature range: -30ºC to +85ºC • Dimensions, excluding connectors: 78.1 x 66.8 x 37.2mm • Weight: < 190 g • IP30 enclosure • Internal 1650mAh Li-Po battery (*) www.mtxm2m.com 2017/07 v1.2 Page 16 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 17 USB, MUX driver for Microsoft® Windows XP™, Vista™, Windows 7™ • RIL, USB driver for Microsoft® Windows Embedded Handheld™ >= 6.x • USB, MUX driver for Microsoft® Windows Embedded Compact™ >= 5.x • USB serial/CDC-ACM driver for Linux www.mtxm2m.com 2017/07 v1.2 Page 17 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 18 Multiplexer according 3GPP TS 27.010 • RLS Monitoring (Jamming detection) • Informal Network Scan • Customer IMEI/SIM-Lock as variant • Integrated FOTA, configurable and royalty free *: depending on model, see Section 1.3 www.mtxm2m.com 2017/07 v1.2 Page 18 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 19: Product Label
MTX-xG-JAVA-IoT Family 1.6 Product label The label fixed to the bottom of a MTX Terminal comprises the following information: Information MTX Terminals logo Product name (model) Product ordering number Hardware and Firmware Revisions FCC ID Year/Week of fabrication Barcode (Code 128) (IMEI)
Page 20: Main Features And Services
MTX-xG-JAVA-IoT Family 1.7 Main features and services The MTX-IoT performs a set of telecom services (TS) according to GSM standard phase 2+, ETSI and ITU-T. The services and functions of the MTX-3G-JAVA are implemented by issuing customized applications embedded on the device, by AT commands issued internally or over the USB, RS232 or RS485 interface.
Page 21 Supports a USB 2.0 High Speed (480Mbit/s) device interface, Full Speed (12Mbit/s) compliant RS232 (8-wire) Adjustable baud rates: 1200bps to 921600bps Autobauding: 1200 to 230400bps Supports RTS/CTS hardware flow control Multiplex ability according to GSM 07.10 Multiplexer Protocol www.mtxm2m.com 2017/07 v1.2 Page 21 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 22 Emergency reset by hardware signal TURN_OFF Special features Antenna SAIC (Single Antenna Interference Cancellation) / DARP (Downlink Advanced Receiver Performance) Rx Diversity (receiver type 3i – 64-QAM) / MIMO www.mtxm2m.com 2017/07 v1.2 Page 22 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 23: Operating Modes
Airplane mode shuts down the radio part of the device, causes the modem to log off from the GSM/GPRS network, and disables all AT commands whose execution requires a radio connection. Airplane mode can be controlled by AT command www.mtxm2m.com 2017/07 v1.2 Page 23 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 24: Power Consumption
Average times: SLEEP and ULP mode – 3 minutes, transfer modes – 1.5 minutes Communication tester settings: no neighbor cells, no cell reselection etc., RMC (reference measurement channel) Description Conditions Max Unit ULP mode supply = 25ºC µA current = 85ºC µA www.mtxm2m.com 2017/07 v1.2 Page 24 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 25: Rf Antenna Interface Description
GSM 1800 / GSM 1900 GPRS, 2 TX GSM 850 / E-GSM 900 GSM 1800 / GSM 1900 EDGE, 2 TX GSM 850 / E-GSM 900 GSM 1800 / GSM 1900 www.mtxm2m.com 2017/07 v1.2 Page 25 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 26 GSM 1800 / GSM 1900 (ROPR = 4, i.e. EDGE, 1 TX GSM 850 / E-GSM 900 maximum reduction) GSM 1800 / GSM 1900 GPRS, 2 TX GSM 850 / E-GSM 900 www.mtxm2m.com 2017/07 v1.2 Page 26 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 27: Sim Card
Older 5V SIM technology is not supported. 1.8 Precautions MTX-IoT as a standalone item is designed for indoor use only. For outdoor use it must be integrated into a weatherproof enclosure. Do not exceed the environmental and electrical limits as specified in Technical Data www.mtxm2m.com...
Page 28: Block Diagram
MTX-xG-JAVA-IoT Family 1.9 Block diagram 1.9.1 Models with CAN bus, 1-Wire and/or Latch Relay The MTX-IoT modems containing CAN bus, 1-Wire and/or Latch Relay have the following block diagram: Note *1: DB9 connector only available in STD and DB9 variants. See section 1.2...
Page 29: Models With Power Relay 220Vac/6A
MTX-xG-JAVA-IoT Family 1.9.2 Models with Power Relay 220VAC/6A The MTX-IoT modems containing a 220VAC/6A Power relay have the following block diagram: Note *1: DB9 connector only available in STD and DB9 variants. See section 1.2 Note *2: DB15 HD connector only available in STD and DB15 variants. See section 1.2...
Page 30: Models With Rj11 Connector And/Or Analog Audio
MTX-xG-JAVA-IoT Family 1.9.3 Models with RJ11 connector and/or analog audio The MTX-IoT modems with RJ11 connectors and/or analog audio have the following block diagram: Note *1: DB9 connector only available in STD and DB9 variants. See section 1.2 Note *2: DB15 HD connector only available in STD and DB15 variants. See section 1.2...
Page 31: All Other Models
MTX-xG-JAVA-IoT Family 1.9.4 All other models The general MTX-IoT modem’s block diagram is shown in the following figure: Note *1: DB9 connector only available in STD and DB9 variants. See section 1.2 Note *2: DB15 HD connector only available in STD and DB15 variants. See section 1.2...
Page 32: Hardware Revisions
MTX-xG-JAVA-IoT Family 1.10 Hardware revisions Hardware Revision Starting production date Changes 1.03 02/2016 Initial version www.mtxm2m.com 2017/07 v1.2 Page 32 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 33: Mechanical Description
SIM Card Reader, DIP switches & batt jumper GSM Antenna Connector DB9 connector DB15 connector Mounting holes Mounting holes Mini USB 2.0 Connector Power Supply Connector 5-way plug-in 5.00mm pitch terminal block www.mtxm2m.com 2017/07 v1.2 Page 33 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 34: Models With 7-Way Plug-In 3.50Mm Pitch Terminal Block
SIM Card Reader, DIP switches & batt jumper GSM Antenna Connector DB9 connector DB15 connector Mounting holes Mini USB 2.0 Connector GPS or RF Antenna Connector 7-way plug-in 3.50mm pitch terminal block www.mtxm2m.com 2017/07 v1.2 Page 34 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 35: Models With Rj11 Connector
Tri-color Led Indicator SIM Card Reader, DIP switches & batt jumper GSM Antenna Connector DB9 connector DB15 connector Mounting holes Mini USB 2.0 Connector Power Supply & Audio Connectors www.mtxm2m.com 2017/07 v1.2 Page 35 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 36: Dimensions
MTX-xG-JAVA-IoT Family 2.2 Dimensions All dimensions are in millimeters www.mtxm2m.com 2017/07 v1.2 Page 36 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 37 MTX-xG-JAVA-IoT Family All dimensions are in millimeters www.mtxm2m.com 2017/07 v1.2 Page 37 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 38 MTX-xG-JAVA-IoT Family All dimensions are in millimeters www.mtxm2m.com 2017/07 v1.2 Page 38 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 39: Electrical And Environmental Characteristics
Driver output resistance VIN = 0V Ω Receiver positive-going input threshold voltage Receiver negative-going input threshold voltage Receiver input hysteresis (V Receiver input resistance Input voltage ±3 to ±25V kΩ www.mtxm2m.com 2017/07 v1.2 Page 39 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 40: Rs485 Interface
3.1.4 Counter input ABSOLUTE MAXIMUM RATINGS Symbol Parameter Conditions Min. Max. Unit Input voltage range CHARACTERISTICS Symbol Parameter Conditions Min. Typ. Max. Unit High-level input voltage Low-level input voltage www.mtxm2m.com 2017/07 v1.2 Page 40 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 41: Optoisolated Input/Output
=100Ω µs Turn-off time =2V, I =1mA, R =100Ω µs Please see equivalent circuits in Section 4.4.4 to view voltage input/output ranges and determine operating conditions in each case. www.mtxm2m.com 2017/07 v1.2 Page 41 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 42: Analog Input/Output
VCANH=12V, CANH open Positive-going input voltage Negative-going input voltage Hysteresis voltage (V Input capacitance Differential input capacitance Differential input resistance kΩ Input resistance (CANH or CANL) to kΩ ground www.mtxm2m.com 2017/07 v1.2 Page 42 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 43: Wire
At 10mA 30mVDC mΩ Switching current Switching voltage Electrical endurance Resistive load, at 70ºC, 1s on 9s off, cycles 0.5A 125VAC Mechanical endurance cycles Insulation resistance At 500VDC 1000 MΩ www.mtxm2m.com 2017/07 v1.2 Page 43 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 44: Operating Temperatures
Note that within the specified operating temperature ranges the unit temperature may vary to a great extent depending on the operating mode, used frequency band, radio output power and current supply voltage. www.mtxm2m.com 2017/07 v1.2 Page 44 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 45: Storage Conditions
Mechanically active substances Not recommended IEC TR 60271-3-1:1S1 Sinusoidal vibration: IEC TR 60271-3-1:1M2 Displacement Acceleration m/s2 Frequency range 2-9 9-200 Shocks: IEC 60068-2-27 Ea Shock spectrum semi-sinusoidal Duration Acceleration m/s2 www.mtxm2m.com 2017/07 v1.2 Page 45 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 46: Interface Description
7-way plug-in 3.50mm pitch terminal block (power supply, CAN bus, 1-Wire bus and Latch Relay) • SIM card reader • FME male coaxial jack (antenna connector) • SMA female coaxial jack (GPS/GNSS antenna connector) or other RF options www.mtxm2m.com 2017/07 v1.2 Page 46 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 47: Power Supply Connector
12VDC power supply. The power supply has to be a single voltage source capable of providing a peak during an active transmission. The uplink burst causes strong ripples (drop) on the power lines. By default, the MTX-IoT will automatically switch on when power supply is applied at PIN 1 and PIN 2. Signal...
Page 48: Models With Power Relay 220V/6A (5-Way Plug-In 5.00Mm Pitch Terminal Block)
12VDC power supply. The power supply has to be a single voltage source capable of providing a peak during an active transmission. The uplink burst causes strong ripples (drop) on the power lines. By default, the MTX-IoT will automatically switch on when power supply is applied between PIN 2 and PIN 1.
Page 49: Models With Rj11 Connector
12V DC power supply. The power supply has to be a single voltage source capable of providing a current peak during an active transmission. The uplink burst causes strong ripples (drop) on the power lines. MTX-IoT devices are shipped to automatically switch on only with supply between PIN 1 and PIN 6. Signal Direction...
Page 50: All Other Models (5-Way Plug-In 5.00Mm Pitch Terminal Block)
12VDC power supply. The power supply has to be a single voltage source capable of providing a peak during an active transmission. The uplink burst causes strong ripples (drop) on the power lines. By default, the MTX-IoT will automatically switch on when power supply is applied between PIN 2 and PIN 1.
Page 51: Mini Usb Connector
This is because MTX-IoT is designed as a self-powered device compliant with the “Universal Serial Bus Specification Revision 2.0”. The MTX-IoT cannot be powered by a USB port. Only modems that have a mounted an internal Li-Po battery (B) can operate with USB power voltage.
Page 52: Db9 Connector: 8-Wire Rs232 Port
DIP switches in order to select the port of your choice. The MTX-IoT modem is designed to be used as a DCE (data circuit-terminating equipment). Based on the conventions for DCE-DTE connections, it communicates with the customer application (DTE- data terminating equipment) using the following signals: •...
Page 53 CSD and fax services only available on the first logical channel. • The DTR0 signal will only be polled once per second from the internal firmware of MTX-IoT. • The default configuration is 8 data bits, no parity and 1 stop bit. The setting can be changed using the AT command AT+ICF and, if required, AT^STPB.
Page 54: Db15 Hd Connector: I/O Expansion Port
Opto-isolated input 2 (active low) OUT 4 Output Opto-isolated output 4 (open collector) ADC 2 Input Analog to Digital converter input 2 Ground connection ADC 1 Input Analog to Digital converter input 1 www.mtxm2m.com 2017/07 v1.2 Page 54 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 55: Rs232 Interface
DIP switches in order to select the port of your choice. The MTX-IoT modem is designed to be used as a DCE (data circuit-terminating equipment). Based on the conventions for DCE-DTE connections, it communicates with the customer application (DTE- data terminating equipment) using the following signals: •...
Page 56: Analog Inputs
Both ADC inputs have a resolution of 10 bits, which means that the default resolution is 48.8mV (0- 50V). The A/D converter uses the successive approximation conversion technique. The maximum A/D conversion rate is 5 samples per second. To know how to read the analog inputs values please read the MTX-IoT Family Software Manual www.mtxm2m.com 2017/07 v1.2 Page 56 MTX M2M®...
Page 57: Optoisolated I/O
0.9V ≤ V ≤ 30V → Logic ‘1’ Logic ‘1’ → V = HiZ To know how to read and write these lines please read the MTX-IoT Family Software Manual www.mtxm2m.com 2017/07 v1.2 Page 57 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 58: Counter Input
0V ≤ V ≤ 1V → Logic ‘1’ 1.5V ≤ V ≤ 40V → Logic ‘0’ To know how to use this counter please read the MTX-IoT Family Software Manual www.mtxm2m.com 2017/07 v1.2 Page 58 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 59: Rs485 Bus
+RxA RS485 A signal (see section 4.6 for details) Automatic Restart after Shutdown Enable Signal (not available AUTO ON Input 0-VIN in MTX-65i-RS485 FW2.00 (AUTO-ON) and MTX-65i-RS485-LC) Input 6.5-40VDC Positive power input Input Negative power (ground) www.mtxm2m.com 2017/07 v1.2 Page 59...
Page 60: Can Bus And 1-Wire Bus
1-Wire bus data signal RL_COM Latch relay Common contact RL_NO Latch relay Normally Open contact Please read the MTX-IoT Family Software Manual to learn how to use these interfaces www.mtxm2m.com 2017/07 v1.2 Page 60 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 61: Dip Switches
MTX-xG-JAVA-IoT Family 4.7 DIP switches The MTX-IoT modems include 8 DIP microswitches allowing the user to configure some functionalities of the device. These switches are located close to the SIM card holder, so you can access them through the same removable panel of the SIM card holder.
Page 62: Relays
MTX-xG-JAVA-IoT Family 4.8 Relays Those MTX-IoT models ordered with Relay option (L for Latch Relay or R for Power Relay) include an internal relay whose contacts are available in the device connectors. Latch Relay Devices including a Latch Relay have a 7-way plug-in 3.5mm pitch terminal block where the relay contacts (Common and Normally Open) are available, shared with the Power Supply input, CAN bus and 1-Wire.
Page 63 220VAC/6A relay Normally Close contact RL_COM 220VAC/6A relay Common contact RL_NO 220VAC/6A relay Normally Open contact To learn how to use commute the relay contacts please read the MTX-IoT Family Software Manual www.mtxm2m.com 2017/07 v1.2 Page 63 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 64: Analog Audio Interface
MTX-xG-JAVA-IoT Family 4.9 Analog audio interface Those MTX-IoT models ordered with Audio option (A) have a 6-way 4-pole RJ connector, as shown below, allowing a telephone handset to be plugged into the modem and giving access to the microphone and earpiece signals. The connector may also be used to drive other analog audio sub- systems or devices.
Page 65 When shipped from the factory, all audio parameters of MTX-65i are set to interface 1 and audio mode 1. This is the default configuration optimized for the Votronic HH-SI-30.3/V1.1/0 handset and used for type approving the MTX Terminals reference configuration.
Page 66: Gsm/Gprs/Umts Antenna Connector
SIM card reader The MTX-IoT modem is fitted with a SIM card reader designed for 1.8V and 3V SIM cards. It is the flip- up type which is lockable in the horizontal position and is accessed through a removable panel as shown below.
Page 67: Internal Li-Po Battery
4.12 Internal Li-Po battery MTX-IoT modems ordered with Battery (B) option mount an internal 3.7V 1650mAh Li-Po battery. The units are shipped with the battery disconnected. To connect it please open the removable panel of the device enclosure and locate the battery jumper near the SIM card holder and the DIP switches, just...
Page 68 30 minutes. Please note that the minimum battery level module switches off automatically, when the battery voltage is around 3.65V (please remember to check using the AT^SBV command). www.mtxm2m.com 2017/07 v1.2 Page 68 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 69 Note: there are two internal LEDs that provide information about the battery status: • A red LED will illuminate when the battery is charging. • A green LED will illuminate when external power is applied. www.mtxm2m.com 2017/07 v1.2 Page 69 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 70: Real Time Clock
“time stamp” messages. This RTC is supplied by a separate voltage regulator which is also active when the MTX-IoT is in power down mode and the power supply VIN is available. An alarm function is provided that allows the MTX- IoT to wake up in Airplane mode without logging onto the GSM/UMTS network.
Page 71: Gps Antenna Connector
MTX-xG-JAVA-IoT Family 4.14 The MTX-IoT ordered with GPS option (2G/GPS or 3G/GPS) has an internal GPS receiver which offers the full performance of GPS technology. The GPS receiver continuously tracks all satellites in view, thus providing accurate satellite positioning data.
Page 72: Gps Antenna Interface Characteristics
Acquisition Sensitivity Open sky Active antenna or LNA -150 Passive antenna -145 Time-to-First-Fix (TTFF) Hot (average at -140dBm) <2 Warm (average at -140dBm) <35 Cold (average at -140dBm) <46 www.mtxm2m.com 2017/07 v1.2 Page 72 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 73: Internal Modules
4.15 Internal modules MTX-IoT modems can be shipped with up to two internal RF cards installed which allows for use with almost all protocols that exist nowadays, such as Bluetooth, WiFi, ISM, ZigBee, etc. The RF card is connected to the internal coprocessor. This means that models mounting an RF card, there will be only one serial port (DB9, DB15 HD, RS485,…) available to be used.
Page 74: Firmware Updates
MTX-xG-JAVA-IoT Family 4.16 Firmware updates It is possible and sometimes necessary to update the MTX-IoT firmware. Updates must be carried out by an approved technician. Please contact gsmsupport@matrix.es for details regarding Service/Programming. www.mtxm2m.com 2017/07 v1.2 Page 74 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 75: Operation
5.2 Power modes The MTX-IoT devices ordered with Ultra Low Power (U) or Low Power (L) options can enter into two reduced consumption power modes depending the option: Ultra Low Power or Low Power.
Page 76: Low Power Mode
When a LP modem enters in Low Power mode, the device will wake up again when it receive a character sent from any of the serial interfaces (RS232 or RS485) To learn how to configure and enter into the Low Power mode please read the MTX-IoT Family Software Manual www.mtxm2m.com...
Page 77: Status Leds
Medium blink: 500ms ON, 500ms OFF • Slow blink: 1000ms ON, 1000ms OFF • Pulse: 100ms ON, 900ms OFF To learn how to use these LEDs please read the MTX-IoT Family Software Manual www.mtxm2m.com 2017/07 v1.2 Page 77 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 78: At Command Interpreter
This eliminates the need for the user to enter AT commands, such as +++ and ATO, as well as switching back and forth between command and online mode when working on one interface only. www.mtxm2m.com 2017/07 v1.2 Page 78 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 79: Embedded Applications
MTX-xG-JAVA-IoT Family 7. Embedded applications The MTX-IoT can embed an internal application written in popular JAVA language. Java technology and several peripheral interfaces on the modem allow you to easily integrate your application. This way, the customer application can be reduced because all the resources (Microcontroller, Flash & RAM memory and all kind of I/O and bus peripheral) can be used by the customer.
Page 80: Mtx-Tunnel Software Application
If you are not a JAVA expert and you do not have experts on hand in your company, we have a readily compiled JAVA code which fits into 99% of M2M applications: MTX-TUNNEL. This is optional and must be ordered separately.
Page 81 Firewall IP • User API • Telemetry (GPIOs and GPS) • Serial RS232/485 – HTTP tunnel • Serial RS232/485 – SMS tunnel • Timing synchronization • ModBus • RF Gateway www.mtxm2m.com 2017/07 v1.2 Page 81 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 82: Safety And Product Care
8.2 General precautions The MTX-IoT modem as a standalone item is designed for indoor use only. For outdoor use it must be integrated into a weatherproof enclosure. Do not exceed the environmental and electrical limits as specified in “Technical Data”.
Page 83: Sim Card Precautions
MTX-xG-JAVA-IoT Family • In order to provide strain relief and to avoid transmitting excessive vibration to the modem during installation, all cables connected to the MTX-IoT modem must be secured or clamped immediately adjacent to the modem's connectors. • To protect the power supply cables, and in order to comply with fire safety requirements, when the unit is powered from a battery or a high current supply, a fast 1.25A fuse should be...
Page 84: Radio Frequency (Rf) Exposure And Sar
20cm from the body. In all other configurations the user is responsible for meeting the local SAR regulations. Users of the MTX-IoT wireless modem device are responsible for ensuring that they meet the SAR regulatory requirements of the countries in which they intend to operate the device and that their documentation contains the relevant SAR declaration, certification information and user guidance as appropriate.
Page 85: Modem Installation
MTX-xG-JAVA-IoT Family 9. Modem installation This chapter gives you advice and helpful hints on how to integrate the MTX-3G-JAVA Terminal into your application from a hardware perspective. 9.1 Where to install the modem There are several conditions which need to be taken into consideration when designing your application as they might affect the modem and its function.
Page 86: How To Install The Modem
Where access is restricted, it may be easier to connect all the cables to the modem prior to securing it in the application. • Securely attach the MTX-3G-JAVA Terminal modem to the host application using two 3mm diameter pan-head screws 9.3 Antenna 9.3.1 General...
Page 87: Antenna Placement
Hand-over occurs as you move from one cell to another in the GSM network. Your mobile application call is transferred from one cell to the next. Hand-over can briefly interfere with communication and may cause a delay, or at worst, disruption. www.mtxm2m.com 2017/07 v1.2 Page 87 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 88: Conformity Assessment
Unique identification of this DoC: MTX-3G-JAVA-IoT RED DoC MATRIX ELECTRONICA S.L. C/ Alejandro Sanchez 109 28019 Madrid Spain Declare under our sole responsibility that the MTX-3G-JAVA-IoT family products MTX-3G-JAVA-IoT-STD-N (EHS6) 199801393 MTX-3G-JAVA-IoT-STD-G (EHS8) 199801394 Terminal containing Cellular Engine Cinterion EHS6/EHS8 Type L30960-N2950-A300/ L30960-N2900-...
Page 89: Fcc Compliant
MTX-xG-JAVA-IoT Family 10.1 FCC Compliant MTX-IoT and any variants contain FCC ID: QIPEHS6. The FCC Equipment Authorization Certification for the EHS6 Module is listed under the FCC identifier QIPEHS6 Industry Canada Certification Number: 7830A-EHS6 granted to Gemalto M2M GmbH. The Cinterion reference application of the EHS6 Module registered under the above identifier is certified to be in accordance with the following Rules and Regulations of the Federal Communications Commission (FCC).
Page 90: Declaración De Conformidad (Spanish)
Spain 11.1 Marcado CE- Directiva RED Declaramos bajo nuestra responsabilidad que los productos MTX-IoT que contienen un módulo celular Cinterion EHS6 (tipo L30960-N2950-A100), al cual se refiere esta declaración, están conformes con la Directiva RED 2014/53/EU • EMC (art 3.1.b): EN 301 489-1 V2.2.0, EN 301 489-52 V1.1.0, EN 301 489-3 V2.1.1 •...
Page 91: Conformidad Fcc
MTX-xG-JAVA-IoT Family 11.2 Conformidad FCC MTX-IoT y todas sus variantes contienen el FCC ID: QIPEHS6. El Certificado de Autorización de Equipo de la FCC para el módulo EHS6 está listado con el identificador FCC QIPEHS6 Número de Certificación de Industria en Canadá: 7830A-EHS6 asignado a Gemalto M2M GmbH.
Page 92: Regulatory And Type Approval Information
12.1 Directives and standards The MTX-IoT modem has been designed to comply with the directives and standards listed below. It is the responsibility of the application manufacturer to ensure compliance of the final product with all provisions of the applicable directives and standards, as well as with the technical specifications provided in this document.
Page 93 Please see next table for an overview of toxic or hazardous substances or elements that might be contained in product parts in concentrations above the limits defined by SJ/T 11363-2006. www.mtxm2m.com 2017/07 v1.2 Page 93 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 94: Sar Requirements Specific To Portable Mobiles
12.3 SELV requirements The power supply connected to the MTX-IoT modem shall be in compliance with the SELV requirements defined in EN 60950-1. www.mtxm2m.com 2017/07 v1.2 Page 94 MTX M2M®...
Page 95: Rohs Statement
MTX-xG-JAVA-IoT Family 13. RoHS Statement The MTX-IoT modem is compliant with the 2002/95/EC (RoHS 1) and 2011/65/EC (RoHS 2) directives of the European Parliament and of the Council of 27 January 2003 (and revised on 8 June 2011) on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS).
Page 96: Abbreviations
Equivalent Isotropic Radiated Power Electromagnetic Compatibility Effective Radiated Power Electrostatic Discharge European Telecommunication Standard ETSI European Telecommunications Standards Institute Federal Communications Commission (U.S.) Frequency Division Duplex FDMA Frequency Division Multiple Access www.mtxm2m.com 2017/07 v1.2 Page 96 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 97 Personal Communication System, also referred to as GSM 1900 Pull Down resistor (appr. 100k) Protocol Data Unit Phase Locked Loop Point-to-point protocol Packet Switched Phase Shift Keying Power Supply Unit www.mtxm2m.com 2017/07 v1.2 Page 97 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 98 Universal Mobile Telecommunications System Unsolicited Result Code Universal Serial Bus USIM UMTS Subscriber Identification Module USSD Unstructured Supplementary Service Data VSWR Voltage Standing Wave Ratio WCDMA Wideband Code Division Multiple Access www.mtxm2m.com 2017/07 v1.2 Page 98 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 99: At Command Summary
(TE) to the terminal adaptor (TA). The command line consists of a string of alphanumeric characters. It is sent to the MTX-IoT to instruct it to perform the commands specified by the characters.
Page 100 Select Preferred Operator List AT+CPMS Preferred SMS message storage AT+CPOL Preferred Operator List AT+CPUC Price per unit and currency table AT+CPWD Change Password AT+CR Service reporting control AT+CRC Incoming Call Indication Format www.mtxm2m.com 2017/07 v1.2 Page 100 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 101 Internet Connection Information AT^SICS Internet Connection Setup Profile AT^SIND Extended Indicator Control AT^SIPS Internet Profile Storage AT^SISC Internet Service Close AT^SISE Internet Service Error Report AT^SISH Internet Listener Service Disconnect www.mtxm2m.com 2017/07 v1.2 Page 101 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 102 Mobile originated call using specific memory and index number ATD><n> Mobile originated call from active memory using index number ATD><str> Mobile originated call from active memory using corresponding field ATDL Redial last number used www.mtxm2m.com 2017/07 v1.2 Page 102 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 103 Set number of seconds to wait for connection completion ATS8 Comma Dial Pause Time Result code format mode CONNECT Result Code Format Restore AT Command Settings from User Defined Profile www.mtxm2m.com 2017/07 v1.2 Page 103 MTX M2M® by MATRIX ELECTRONICA S.L.U...
Page 104 MTX-xG-JAVA-IoT Family 17. Accessories The MTX-IoT has a wide range of available accessories, including: • Power supplies • All type of antennas (indoor, outdoor, high gain, etc…) • Cables and DIN adapters The MTX-IoT is shipped without any accessories. Please visit the following web sites to see the full range of accessories: •...
Page 105: Sales Contact
Fax: 902 99 54 14 (PORTUGAL) Phone 1: 902 19 81 46 Phone 1: +351218162625 Phone 1: +56(9)53369943 Fax 1: 902 99 54 14 Fax 1: +351218149482 Phone 2: +56(9)74822647 www.mtxm2m.com 2017/07 v1.2 Page 105 MTX M2M® by MATRIX ELECTRONICA S.L.U...

This manual is also suitable for:

Mtx-4g-java-iot

MTX -3G-JAVA-IoT User Manual

Quick Links

User Manual

Need help?

Questions and answers

Related Manuals for MTX MTX-3G-JAVA-IoT

Summary of Contents for MTX MTX-3G-JAVA-IoT

This manual is also suitable for:

Table of Contents