Daikin ERGA04DAV3A Installer's Reference Manual page 29

Item Description
7 Room thermostat
8 Outdoor ambient
temperature sensor
9 Indoor ambient
temperature sensor
10 Heat pump convector
Field supplied components
11 Shut-off valve
12 Electricity meter
13 Domestic hot water
pump
14 Alarm output
15 Changeover to external
heat source control
16 Space cool/heat
operation control
17 Power consumption
digital inputs
18 Safety thermostat
(a) Refer to name plate on outdoor unit.
(b) Minimum cable section 0.75 mm².
(c) Cable section 2.5 mm².
(d) Cable section 0.75 mm² till 1.25 mm²; maximum length:
50 m. Voltage-free contact shall ensure the minimum
applicable load of 15 V DC, 10 mA.
(e) Cable section 0.75 mm² till 1.25 mm²; maximum length:
500 m.
(f) Cable section 1.5 mm².
NOTICE
More technical specifications of the different connections
are indicated on the inside of the indoor unit.
Backup heater Power supply
type
*3V 1N~ 230 V
*6V 1N~ 230 V
3~ 230 V
*9W 3N~ 400 V
7 Installation
7.1 Overview: Installation
This chapter describes what you have to do and know on-site to
install the system.
Typical workflow
Installation typically consists of the following stages:
1 Mounting the outdoor unit.
2 Mounting the indoor unit.
3 Connecting the refrigerant piping.
4 Checking the refrigerant piping.
5 Charging refrigerant.
6 Connecting the water piping.
7 Connecting the electrical wiring.
8 Finishing the outdoor installation.
9 Finishing the indoor installation.
Final English - Tanslations in progress
ERGA04~08DAV3(A) + EHVH/X04+08S18+23DA
Daikin Altherma – Low temperature split
4P495248-1 – 2017.12
Wires Maximum
running
current
(b)
3 or 4 100 mA
(b)
2
(b)
2
(b)
2 100 mA
(b)
2 100 mA
(b)
2 (per meter)
(b)
2
(b)
2
(b)
2
(b)
2
(b)
2 (per input
signal)
(d)
2
Required number of
conductors
2+GND
2+GND
3+GND
4+GND
INFORMATION
If you have limited installation space, do the following
before installing the unit in its final position:
connect the drain hose to the drain" on page
requires to remove one or both side panels.
INFORMATION
Depending on the units and/or the installation conditions, it
might be necessary to connect electrical wiring before you
can charge refrigerant.
7.2 Opening the units
7.2.1 About opening the units
At certain times, you have to open the unit. Example:
▪ When connecting the refrigerant piping
▪ When connecting the electrical wiring
▪ When maintaining or servicing the unit
DANGER: RISK OF ELECTROCUTION
Do NOT leave the unit unattended when the service cover
is removed.
7.2.2 To open the outdoor unit
DANGER: RISK OF ELECTROCUTION
DANGER: RISK OF BURNING
See "7.5.8 To connect the refrigerant piping to the outdoor unit" on
page 36 and "7.9.6 To connect the electrical wiring on the outdoor
unit" on page 41.
7.2.3 To open the indoor unit
1 Remove the top panel.
5×
T25
2 Remove the user interface panel. Open the hinges at the top
and slide the top panel upwards.
NOTICE
If you remove the user interface panel, also disconnect the
cables from the back of the panel to prevent damage.
7 Installation
"7.8.5 To
40. It
Installer reference guide
29