Bosch KT700VCI User Manual page 23

9.4.5.4 �learingData
This function is used to clear the comparison between
data streams.
Operation Steps:
¶
Click the "Clear" button to clear the history values
of data comparison; meanwhile, the "Clear" button
switches to the "Compare" button.
9.4.5.5 DisplayModesofDataStreams
The value of a data stream can be displayed in three
modes, i.e. numeral, waveform and control. The nume-
ral display mode is taken as a default.
Operation Steps:
1. After reading the data streams, the values of read
data streams will be displayed in numerals;
2. Click the "Numeral" button and select "Waveform"
from the pop-up options; then the values of data
streams will be displayed in waveforms, and the "Nu-
meral" button will switch to the "Waveform" button;
3. Click the "Waveform" button and select "Control"
from the pop-up options; then the values of data
streams will be displayed in controls and the "Wave-
form" button will switch to the "Control" button;
4. Click the "Control" button and select "Numeral" from
the pop-up options; then the values of data streams
will be displayed in numerals and the "Control" but-
ton will switch to the "Numeral" button.
i
The button status switches in compliance with the
mode in which the current data streams are dis-
played.
9.4.6 TravelRecorder
The travel recorder is mainly used to record some data
of ECU for a long time. Each data is continuous recor-
ding up to 2 hours. During the course of recording,
it can save the data at any time and save them in the
".REC" format under the specified folders.
You may click the "Travel Recorder"
"Read Data Stream" interface to proceed to the "Travel
Recorder" interface.
Bosch Automotive Diagnostics Equipment (Shenzhen) Limited
Parameter Description:
 $
Period: according to the period you select, the
system will automatically match it with the selec-
table data streams; the system provides 3 optio-
nal periods, i.e. 250 ms, 500 ms and 1000 ms; the
default period is 250 ms;
 $
Maximum Records: according to the period, the
system will automatically match it with maximum
records.
 $
RecordTime: it can be manually set to 10 min
as a minimum and 120 min as a maximum; the
default record time is 120 min;
 $
TriggerTime: it can be manually set to 20 s as a
minimum and 120 s as a maximum; the default
trigger time is 20 s.
Operation Steps:
1. Select the period you desire;
2. Select the record time you desire;
3. Select the trigger time you desire;
4. Select the desired data stream to be recorded; if you
don't select a data stream, the system will pop up a
warning dialogue box after you press the "Record"
button; if the selected data streams outnumber the
displayed maximum records, the system will also
pop up a warning dialogue box;
5. Click the "
6. Click the "Record" button to stop the recording;
enter the file name in the pop-up dialogue box, and
click "Save" to save the currently recorded data.
i

TriggerRecords: when you click this button, the VCI
will automatically save the data streams within the
trigger time to the fixed default paths of system; this
function supports the data stream playback;
i
How to start recording (on the premise that you have
proceeded to the software interface of travel recor-
ding function):
$
Click the "Record" button on the software inter-
button at the face of travel recording function;
$
Press the "Record" button on the VCI host;
$
Correctly connect one end of recorder cable to
the VCI host, and press the button on the other
end of recorder cable;
i
How to use the recorder cable: hold on (i.e. the buz-
zer continuously sounds for 3 times) to start/stop
the travel recording function; press it short (i.e. the
buzzer sounds once) to trigger the record;
i
The save paths for the recorded data are system
defaults and cannot be modified.
i
You may monitor the data record time by the time
progress bar on the screen.
�ehicleDiagnostic|���|2� ���|2�
" button to start recording;
|2� en