Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Lightspeed CAT AV
Summary of Contents for Lightspeed CAT AV
- Page 2 TABLE OF CONTENTS SECTION 1: System Overview Overview System Components and Unpacking Applications Diagram Wireless Selector Controls I/O Switcher Front Panel Connectors & Controls Amplifier Controls & Connections Video Converter Connectors REDMIKE VC Controls & Connections RMC Cradle Charger Controls & Connections Infrared Sensor/Receiver (ISR) Connections SECTION 2: Important Safety Instructions...
-
Page 3: System Components And Unpacking
Video Converter module where it is converted back to its appropriate video connector and signal type to connect with the classroom projector. Designed for the classroom, CAT AV is fast and simple to install. Three CAT-5 twisted pair cables carry audio and video signals, control signals and power... - Page 4 CA-PLSPK50 Plenum speaker cable (50 ft) REDMIKE VC Velcro strip 2 inch Classroom AC-ENC System Enclosure Microphone AC-MNCAV User Manual SPEAKERS Contact Lightspeed at 800.732.8999 for speaker info SPEAKERS Optional WMQ (x 4) Optional DRQ (x 4) MCQ (x 1)
- Page 5 CAT AV Switcher can select between paging sensor. When a page is four multimedia audio inputs sensed, it mutes all audio output from the CAT AV System during the page. (associated with the video inputs). Audio is returned to its normal levels MICROPhONE INPUTS when the page is complete.
- Page 6 WIRELESS SELECTOR CONTROLS WIRELESS SELECTOR CONTROLS CONT’D Rear Panel 1. CAT AV SySTEM POWER 4. AV INPUT SOURCE SElECT 6. AV MUTE/AV MUTE Likewise, three pushes of the SWITCh/POWER INdICATOR: ANd SOURCE INdICATORS: INdICATOR: Pushbutton blanks Volume DOWN pushbutton will...
-
Page 7: Connectors And Controls
I/O SWITCHER FRONT PANEL I/O SWITCHER BOTTOM PANEL CONNECTORS AND CONTROLS CONNECTORS “(Picture of bottom side of the switcher showing connectors)” Need image – there’s not one in the Word File. 1. VgA VIdEO WITh AUdIO 1: 5. POWER lIghT: Glows green 1. - Page 8 AMPLIFIER CONTROLS & CONNECTIONS AMPLIFIER CONTROLS & CONNECTIONS CONT’D 1. SySTEM PAIRINg BUTTON: 5. PAgEFIRST INPUT 8. POWER ON lEd: This light glows 12. SPEAkER OUTPUT 1: A phoenix Pushbutton used to synchronize CONNECTOR: A phoenix red when system power is turned connector outputting audio signal the Wireless Selector to the system connector connects the system...
- Page 9 CONNECTOR: A 15-pin Dsub battery should only be replaced microphone, we recommend using (female) connector outputs VGA by a Lightspeed AA rechargeable Channel A. video signals to be carried to sensing battery (part # BA- 7. VOlUME CONTROlS (UP –...
- Page 10 3. SENSOR OUT: Connect the Cat 5 will glow blue when the ISR is sensor cable to this connection to receiving power from the CAT AV. send audio from the microphones 1. ChARgE INdICATORS: The light 2. dC POWER PORT: Connect the (There is a blue light in the center to the CAT AV amplifier.
-
Page 11: Installation
Lightspeed product is operated. personnel. The user should not The safety and operating attempt to service this Lightspeed instructions should be kept for product. Keep all original future reference. All operating and packaging for easy transport if other instructions should repair or return is necessary. - Page 12 sysTEM InsTALLATIOn OVErVIEW On/In WALL (nO EnCLOsurE) COnT’D system Components can be installed in a variety of locations as shown in the following chart. Integrated Video Control Sensor/ For on the wall installation For in wall installation Switcher Amplifier Converter Panel receiver speakers • Mark mounting screw/wall- • Install the 4-gang mud ring or WALL anchor locations & drill holes electrical box On Wall, In for the switcher (the switcher Enclosure • Pull the CAT-5 cables marked module installs over the 1-gang Audio and Video On Wall, no wall box) Enclosure • Connect the cables to the...
- Page 13 ON/IN WALL (NO ENCLOSURE) ON WALL IN EQUIPMENT ENCLOSURE CONT’D 2. Install the Amplifier Module and Video Converter 1. Install System Wall Plates & I/O Switcher Install Amplifier on the wall by the Install Video Converter at the • Label both ends of all cables • Pull the 50’ Speaker wire(s) switcher Projector...
-
Page 14: Getting Started
• Label both ends of all cables (see • Connect the cables to the Audio page 22) and Video outputs on the Switcher To get started using the CAT AV two things need to happen: • Mark (with painters tape) location • Install the wall décor plate on the 1. The wireless selector needs to be synchronized with the system. of CAT AVfour’s Switcher Modules... -
Page 15: Setup Mode
3. SETUP MODE 4. SELECTING SET UP FUNCTION The wireless selector provides access to learn projector IR codes and Each of the set up functions is represented by an LED located on the change factory default settings. The wireless selector front panel as shown set up functions are: in the following figure. - Page 16 The CAT AV uses a 4-band audio equalizer designed to optimize and fine-tune the microphone sound quality for the classroom. Below are some tips on proper CAT AV can have up to 4 microphones. The volume for each of these system equalization:...
-
Page 17: Tone Control Setting
Procedure: The tone control is used to personalize the sound of music played through the CAT AV system. Using the tone control you can increase or decrease the base, 1. Enter Set Up Mode mid frequency, or treble tone of the music. The result will be a full range natural sound for multimedia. - Page 18 Replacing projector bulbs is expensive. To save energy and increase projector 1. Enter Set Up Mode bulb life, CAT AV will turn off the projector after a set elapsed time after the last 2. Make sure LED 3 is glowing green audio is processed by the system.
- Page 19 CONT’D 14. Push the VGA (or computer) To save valuable installation & setup time, CAT AV has a set-up copy mode. After button on the projector remote completing set-up of the first CAT AV system, the set-up information can be control.
- Page 20 Often the IT department will have an additional wireless selector to help The CAT AV can be reset to its factory default settings using this procedure. If troubleshoot a possible problem with a classroom system. (CAT AV can have up to 4 wireless selectors paired to the system at one time.) When the IT department...
-
Page 21: Speaker Configuration
13. SET UP SUMMARY CHART 14. SPEAKER CONFIGURATION When setting up a speaker configuration, the correct speaker impedance loading must be observed. Group 1 Channel A Select volume for each microphone channel Microphone Group 1 Channel B Volume Group 2 Channel A Multimedia Ceiling Speaker Installation Group 2 Channel B Tools and Equipment... - Page 22 14. SPEAKER CONFIGURATION 14. SPEAKER CONFIGURATION CONT’D CONT’D Step 2: Step 3: Installing the Speaker into the Ceiling Securing the MCQ Speaker To Grid The dimensions of the MCQ comply with Building Codes, the speaker are 2’ x 2’ and is designed MCQ speaker MUST be fastened to to lie onto any standard suspended the ceiling grid and secured with a...
- Page 23 Next, find a suitable location for the ISR. Poor location will cause substandard Connecting and Routing Speaker performance of the CAT AV Classroom Audio System. The ISR should be as high as possible in the room – the ceiling is the best location, centered along the Wire longest wall in the room.
- Page 24 ISR. Route the wire back to the or screwdriver behind the ISR to a. Slide the tabs onto the outsides CAT AV amplifier, securing it along press the release bar down and of the t-bar, starting with one with way using surface raceway slide the ISR off the bracket corner.
-
Page 25: Charging The Redmike Vc
Always use a Lightspeed rechargeable sensing battery. Replacement AA NiMH top of the microphone just below batteries may only be purchased through Lightspeed Technologies (part # BA- the collarbone. NOTE: Positioning NH2A27). of the REDMIKE VC is critical for Do not attempt to charge alkaline batteries. -
Page 26: Troubleshooting
LT71/ HM70 is operating on the same channel. If you review these instructions and still have questions, write down the serial number and model number of your system and call lightspeed Technical Services at 800.732.8999, 5 a.m. – 5 p.m., PST. -
Page 27: Specifications
1. Warranty on i nfrared microphones is FIVE (5) YEARS. 2. Warranty on Lightspeed rechargeable batteries, all external cables and wires provided by Lightspeed is one (1) year. 3. Prepaid shipping labels are provided by Lightspeed factory or an authorized CERTIFICATIONS warranty service center for warranty repairs. -
Page 28: Fcc Statement
FCC STATEMENT SYSTEM SPECIFICATIONS AUdIO VIdEO Resolution 1920 x 1200 at 60Hz Video Inputs Four (4) Inputs (VGA 9-pin Dsub x2; Composite RCA x2) FCC Requirements per 15.19(a)(3) and (a)(4) Output (Switcher to Converter) CAT-5e cable (3) All other devices shall bear the following statement in a conspicuous Switcher Dimensions location on the device: Video Converter Dimensions... - Page 29 SYSTEM SPECIFICATIONS SYSTEM SPECIFICATIONS CONT’D CONT’D SWITChER SWITChER CONT’d Video Sync Gain Unity (as a system) Input type RGBHV, RGBS (RGB input) Bandwidth RGB 200 MHz (-3 dB) @ 50' (15 m) of cable Output type RGBHV, RGBS (RGB output, follows input) Composite video 100 MHz (-3 dB) Standards...
- Page 30 SYSTEM SPECIFICATIONS SYSTEM SPECIFICATIONS CONT’D CONT’D AMPlIFIER CONT’d: AMPlIFIER CONT’d: Video Input Infrared Audio Input — Voicelift™ Receiver Number/signal type 1 VGA-UXGA RGBHV, RGBS (follows input Number/signal type 2 mono, balanced (mic and aux) type) Connectors 1 female RJ-45 1 composite video Connectors 1 female RJ-45 connectors Impedance...
- Page 31 lIghTSPEE d TE ChNOlOgIES 1 1509 SW HERMAN RO AD / TUAL ATI N, OR 970 62 TOL L F REE: 800.732 .89 99 / PHO NE: 503.68 4.5 538 / FAX: 503.684.3197 LIG HTSPEE D-TEK. COM MN0235US01-1...
Need help?
Do you have a question about the CAT AV and is the answer not in the manual?
Questions and answers