1. Manuals
  2. Brands
  3. Unicorn Electronics Manuals
  4. Motherboard
  5. ENDAT-3201M
  6. User manual

Unicorn Electronics ENDAT-3201M User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ENDAT-3201M
User's Manual
Rev. 3x
For 3201M PCB ver.1F or later
16/01/2004

Advertisement

Table of Contents
loading

Summary of Contents for Unicorn Electronics ENDAT-3201M

  • Page 1 ENDAT-3201M User’s Manual Rev. 3x For 3201M PCB ver.1F or later 16/01/2004...
  • Page 2 The low power consumption CPU embedded board Copyright Notice The content of this manual has been checked for accuracy. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this manual. The manufacturer reserves the right to make improvements or modification to this document and/or the product at any time without prior notice.
  • Page 3 This manual covers three different layout models, and the respective board layouts are shown in chapter 1-4. Please refer to the following description to make sure which model on hand before using. ENDAT-3201M System Chipset VIA VT8601A + VIA VT82C686B (APOLLO PLE-133)
  • Page 4 The low power consumption CPU embedded board...

  • Page 5: Table Of Contents

    1-2. UNPACKING ......................5 1-3. ELECTROSTATIC DISCHARGE PRECAUTIONS ..........5 1-4. MOTHERBOARD LAYOUT (ENDAT-3201M)..........6 CHAPTER 2. SETTING UP THE MOTHERBOARD......9 2-1. JUMPERS AND CONNECTORS (ENDAT-3201M) ..........9 2-2. INSTALLING MEMORY ..................30 2-3. SHARED VGA MEMORY ..................30 2-4. INSTALLING RISER CARD................30 2-5. ASSIGNING IRQs FOR EXPANSION CARDS..........31 2-6.
  • Page 6 The low power consumption CPU embedded board CHPATER 4. VGA, LCD, DOC FEATURE .........47 4-1. AGP-BUS VGA FEATURE..................47 4-2. LCD FLAT PANEL FEATURE ................48 4-3. PCI BUS AUDIO ADAPTER FEATURES ............49 4-4. DISKONCHIP FEATURE ..................50 4-5. DRIVER UTILITY INSTALLATION GUIDE ............51 CHPATER 5.

  • Page 7: Chapter 1. Introduction

    ENDAT-3201M series CPU boards provides the ultimate solution by integrating with VIA’s technology low power consumption VIA C3 series CPU and VIA EDEN fanless ESP series CPU. ENDAT-3201M series CPU boards offer the assorted functions for various applications such as high-end POS systems, kiosks, networking systems, controlling terminals and other embedded systems.

  • Page 8: Features

    The ENDAT-3201M Embedded CPU Board 1-1. Features Basic Feature: ENDAT-3201M, embedded VIA C3 , Eden , Ezra Low Power EBGA processors. 133 / 100 MHz CPU Front Side Bus (FSB) DRAM interface synchronous or pseudo synchronous with CPU FSB speed...
  • Page 9 ENDAT-3201M-1i: Support 1 Intel LAN ENDAT-3201M-1RL: Support 1 Realtek LAN + LVDS ENDA-3201M-1iL: Support 1 Intel LAN + LVDS Note: The standard version of ENDAT-3201M is embedded with VIA EDEN Fanless ESP5000. Other option CPUs will be provided upon request.

  • Page 10: Unpacking

    1-2. Unpacking The motherboard comes securely packaged in a sturdy cardboard shipping carton. In addition to the User's Manual, the motherboard package includes the following items: • ENDAT-3201M 5.25” SBC / CPU Board • HDD/FDD Cables • TV-Out adapter / cable (Optional) •...
  • Page 11 User’s Manual 1-4. ENDAT-3201M...

  • Page 13: Jumpers And Connectors (Endat-3201M)

    Chapter 2. Setting up the CPU Motherboard 2-1. Jumpers and Connectors (ENDAT-3201M) Jumpers/Connectors Overview: Function Jumpers/Connectors Cooling Fan Connector JFAN1, JFAN2 Power Supply: Power Good JP12: Pin 9~11 ATX Power On/Off Switch JP12: Pin 12~13 Audio Port Connector Printer Port...
  • Page 14 The ENDAT-3201M Embedded CPU Board Function Jumpers/Connectors IDE 1 LED JP12: Pin 1, Pin 2 External Speaker JP12: Pin 3, Pin 6 Buzzer On/Off JP12: Pin 4, Pin 5 Hardware Reset Switch JP12: Pin 7, Pin 8 External Power Good...
  • Page 15 User’s Manual JP10, JP11: RS232 / 422 / 485 Selector for COM2 TYPE JP10 JP11 RS-232 1-2, 4-5, 7-8, 10-11 RS-422/485 Full Duplex 2-3, 5-6, 8-9, 11-12 3-4, 7-8 * Make sure the port mode is set up correctly before installing any peripherals. ** Please also refer to the Appendix B for the pin assignments JP12’s Pin 9~11: On-board Power Good Selector Pin 9-10...
  • Page 16 The ENDAT-3201M Embedded CPU Board CN1: Audio Output Port connector via AV Card Kit (Optional) Please close pin13-14 to disable onboard Audio features if the AV Card Kit is not inserted onto the CN1 connector. If AV card kit is inserted, please make sure the BIOS is enabled with the audio function, since LPT2 and audio function can not be used in the same time.
  • Page 17 User’s Manual CN7: Pin Header for PS2 KB / MS Pin No. Signal (KB) Pin No. Signal(MS) KB Data MS Data +5V(DC) +5V(DC) KB_CLK MS_CLK Printer (LPT1/LPT2) Port Pin No. Description Pin No. Description STB# ACK# BUSY SLCT AFD# ERR# INIT# SLIN# 18-25...
  • Page 18 The ENDAT-3201M Embedded CPU Board LCD_CON1: TFT LCD Panel Port Pin No. Signal Pin No. Signal VDDLCD VDDLCD ENPVEE FPD 23 FPD 22 FPD 17 FPD 16 FPD 11 FPD 10 FPD 9 FPD 8 FPD 21 FPD 20 FPD 15...
  • Page 19 User’s Manual JH1: Close Pin 1-2; Pin 5-6; Pin 7-8...

  • Page 20: Installing Memory

    D,A,B,C AD21 There are two different riser cards that can be fitted to ENDAT-3201M CPU board. The first one is a 98pin ISA only Bus riser card (traditional ISA Bus riser card), the second one is a 188pins PCI/ISA riser card.

  • Page 21: Assigning Irqs For Expansion Cards

    User’s Manual Please using the default setting as above if you are not familiar with the configuration of raiser card and add-on card. Caution: Do not insert PCI Bus Add-On cards directly into the on-board expansion slot! 2-5. Assigning IRQs for Expansion Cards Some expansion cards require an IRQ (Interrupt request vector) to operate.

  • Page 22: Assigning Dma Channels For Isa Cards

    The ENDAT-3201M Embedded CPU Board Status Assignment Used Timer Used Keyboard Used Second 8259 Used COM2 Used COM1 Used COM3 Used Floppy Disk Used LPT1 Used Used LPT2 or Audio Used COM4 Used LAN Adapter (on board) Used PS/2 Mouse...

  • Page 23: Chapter 3. Ami Bios Setup

    Chapter 3. AMI BIOS SETUP AMI BIOS Setup Main Menu Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup PCI / Plug and Play Setup Peripheral Setup Hardware Monitor Setup Setup HDD Security Password Auto-Detect Hard Disks Change User Password Change Supervisor Password Auto Configuration with Optimal Settings...

  • Page 24: Quick Setup

    The ENDAT-3201M Embedded CPU Board 3-1. Quick Setup In most cases, you can quickly configure the system by using the following procedure. The manufacturer highly recommends that you use “Quick Setup” for setting CMOS to avoid any unpredictable results. 1. Choose “Standard CMOS Setup” from the main menu, to configure the date and time, hard disk type, floppy disk drive type etc.

  • Page 25: Advanced Cmos Setup

    User’s Manual 3-3. Advanced CMOS Setup Advanced CMOS Setup Quick Boot Enabled 1st Boot Device Floppy 2nd Boot Device IDE-0 3rd Boot Device CDROM 4th Boot Device Disabled Try Other Boot Devices S.M.A.R.T. for Hard Disks Disabled BootUp Num-Lock Floppy Drive Swap Disabled Floppy Drive Seek Disabled...
  • Page 26 The ENDAT-3201M Embedded CPU Board Password Check This option enables password checking every time the system boots or when you run AMIBIOS Setup. If Always is chosen, a user password prompt appears every time the computer is turned on. If Setup is chosen, the password prompt appears if AMIBIOS is executed.

  • Page 27: Details Of The Advanced Chipset Setup

    User’s Manual 3-4. Details of the Advanced Chipset Setup Advanced Chipset Setup ******** DRAM Timing ******** Configure SDRAM Timing by SPD Enabled DRAM Frequency 133Mhz SDRAM CAS# Latency DRAM Bank Interleave Enabled Memory Hole Disabled AGP Read Synchronization Enabled AGP Fast Write Enabled AGP Aperture Size 128MB...
  • Page 28 The ENDAT-3201M Embedded CPU Board SDRAM Bank Interleave This function is to enable / disable SDRAM Bank Interleave function. Choices: Disabled / Enabled Memory Hole To enabled / disabled (default) the support of Memory Hole which is reserved for ISA card.

  • Page 29: Peripherals Setup

    User’s Manual Peripheral Setup 3-5. Peripheral Setup OnBoard FDC Enabled OnBoard Serial Port 1 3F8/COM1 OnBoard Serial Port 2 2F8/COM2 OnBoard Parallel Port Parallel Port Mode EPP Version Parallel Port DMA Channel Parallel Port IRQ OnBoard Serial Port 3 3E8/COM3 Serial Port3 IRQ OnBoard Serial Port 4 2E8/COM4...
  • Page 30 The ENDAT-3201M Embedded CPU Board Onboard Serial Port 1/2/3/4 This option specifies the base I/O port address of serial port. The settings are Auto (AMIBIOS automatically determines the correct base I/O port address), Disabled, 3F8h, 2F8h, 3E8h, or 2E8h. Onboard Parallel Port This option specifies the base I/O port address of the parallel port on the motherboard.
  • Page 31 User’s Manual Serial Port IRQ This option specifies the IRQ used by the serial port. The default settings are (IRQ)3, (IRQ)4, (IRQ)9 and (IRQ)10. Onboard AC' 97 Audio This function is to disable or enable AC’97 Audio. Choices: Auto; Disabled Onboard Legacy Audio This function allows configuring the Audio Codec to support legacy Sound Blaster mode.

  • Page 32: Power Management Setup

    The ENDAT-3201M Embedded CPU Board 3-6. Power Management Setup Power Management Setup Power Management/APM Enabled Video Power Down Mode Disabled Hard Disk Power Down Mode Disabled Standby Time Out (Minute) Disabled Suspend Time Out (Minute) Disabled Display Activity Ignore IRQ3...
  • Page 33 User’s Manual Standby/Suspend Timer Unit This option specifies the unit of time used for the Standby and Suspend timeout periods. The settings are 4 msec, 4 sec, 32 sec, or 4 min. Display Activity When set to Monitor, this option enables event monitoring on the video display. If set to Monitor and the computer is in a power saving state, AMIBIOS watches for display activity.

  • Page 34: Pci / Plug And Play Setup

    The ENDAT-3201M Embedded CPU Board 3-7. PCI / Plug and Play Setup This section describes the configuration of the PCI bus system. PCI is a system that allows I/O device to operate at speeds nearing the speed of the CPU itself, when communicating with its own special components.
  • Page 35 User’s Manual Display Device Select the display device for system. The available options are CRT Only, CRT + LCD. ** Please note that the text form in the CRT+LCD mode will be shown as the format of LCD mode, not CRT mode; therefore, it will be reading differently on the CRT display. LCD Resolution Select the display resolution for LCD panel.

  • Page 36: Hardware Monitor Setup

    The ENDAT-3201M Embedded CPU Board 3-8. Hardware Monitor Setup Provide some information such as CPU temperature, speed of cooling fan and usage voltage of CPU for user.

  • Page 37: Chpater 4. Vga, Lcd, Doc Feature

    Chapter 4. VGA, LCD, DOC Feature 4-1. AGP-BUS VGA Feature The ENDAT-3201M built-in Graphics Controller is a fully integrated 64-bit 2D/3D Accelerator. The high performance graphics engine offers high speed 3D image processing in full compliance and compatibility with IBM® VGA and VESA™...

  • Page 38: Lcd Flat Panel Feature

    The ENDAT-3201M Embedded CPU Board 4-2. LCD Flat Panel Feature Flat Panel Monitor Interface The on-board graphic controller also support industry standard TFT LCD panel, the interface supports both 18-bit and 24-bit display modes. Optionally, an 18+18 or 24+24 can be supported utilizing external kit (UC-T1848). LVDS interface to...

  • Page 39: Pci Bus Audio Adapter Features

    User’s Manual 4-3. PCI Bus Audio Adapter Features The Chipset built-in SoundBlaster Pro Hardware and Direct Sound Ready AC97’ Digital Audio Controller • Dual full-duplex direct sound channels between system memory and AC97’ link • PCI Master interface with scatter / gather and bursting capability •...

  • Page 40: Diskonchip Feature

    The ENDAT-3201M Embedded CPU Board 4-4. DiskOnChip Feature On board reserved is a 32-pin Socket for DiskOnChip 2000, it is a unique data storage solution to offer a better, faster and more cost effective Flash Disk for applications. The DiskOnChip 2000 provides a Flash Disk (as BIOS expansion) that does not require any additional bus, slot or connector.

  • Page 41: Driver Utility Installation Guide

    User’s Manual 4-5. Driver Utility Installation Guide When finishing the installation of Windows platform (95/98/2000/NT), please install the relative VIA driver (4in1) utilities for compliance compatibility of hardware environment. Insert the support CD that supplied with motherboard into CD-ROM driver which enable the access with auto-run mode;...
  • Page 42 The ENDAT-3201M Embedded CPU Board The Screen will appear VIA 4in1 driver setup screen, please press “NEXT” to continue. Please follow the steps instructed by each screen for the installation of the VIA 4in1 driver. Restart the system after the completion of the installation.

  • Page 43: Chpater 5. Lan Adapter

    Chapter 5. LAN Adapter The on-board LAN adapter use of Single Chip Fast Ethernet Controller, that is highly integrated and requires no “glue” logic external memory on board. It runs in the bus master mode and directly sending/receiving Ethernet packet to/from memory. The On-board LAN adapter can directly fetch the system CPU.

  • Page 44: Utp Cable/Rj-45 Jack Definition

    The ENDAT-3201M Embedded CPU Board 5-2. UTP Cable / RJ-45 Jack Definition Straight through twisted pair cable is typically used to connect a hub to a server or workstation. In a straight through connection, Pin 1 at the server, Pin 2 at the hub connects to Pin 2 at the server, and so on.

  • Page 45: Connecting 100Base-Tx Fast Ethernet Network

    User’s Manual 5-3. Connecting 100Base-TX Fast Ethernet Network The system board provides an RJ-45 port for connection to 100Base-TX Fast Ethernet or 10Base-T Ethernet Network with a single connection over unshielded twisted-pair (UTP). The adapter automatically operates at 10Mbps or 100Mbps when the appropriate 10/100Base hub be connected.

  • Page 46: Remote Boot Function

    The ENDAT-3201M Embedded CPU Board 2. Nominal capacitance: less than 16pF/ft 3. Nominal impedance: 100 ohms 4. Nominal attenuation: less than 11.5db Automatic Selection of the Media Type While the driver installs, it automatically detects the media type based on the type of cable connected.

  • Page 47: Led Indicators

    User’s Manual 5-7. LED Indicators The system board comes with two LED indicators on the edge of the motherboard that indicates the network system status. If you experience any problems with the adapter, first make sure the appropriate driver is loaded, the proper cable is connected to the RJ-45 port and the hub complies with the adapter specification, such as 10Mbps 10Base-T or 100Mbps 100Bast-TX.
  • Page 48 The ENDAT-3201M Embedded CPU Board Note: Before running the setup program, make sure the adapter’s driver is not loaded, otherwise unpredictable results may arise! The setup program can be set the on board configuration to provide diagnostic testing. It is for testing the basic function verification, EEPROM data Access, loop back operation, and the ability to communicate over the network with another adapter.
  • Page 49 User’s Manual network with another adapter to receive and transmit network packets. 4. Software Installation Installing Network Drivers You must install a network driver to allow the adapter to work with your network operating system. The system board provides various network drivers on the driver diskette. The following provides the installation procedures for different network drivers.
  • Page 50 The ENDAT-3201M Embedded CPU Board...

  • Page 51: Appendix A: Flash Memory Utility

    Appendix A: FLASH Memory Utility Using this utility to update the system BIOS from a disk file to the on board Flash memory. Be aware the improper change of the system BIOS will cause the system to malfunction. Using utility as follows: 1.

  • Page 53: Appendix B: Connector Pin Assignment

    Appendix B: Connector Pin Assignment PS/2 Keyboard / Mouse Pin Header Connector (CN7) Pin No. Signal (KB) Pin No. Signal(MS) KB Data MS Data +5V(DC) +5V(DC) KB_CLK MS_CLK D-SUB Type Connector for COM port (RS232) Pin No. Description Pin No. Description Box Header Type Connector for COM port (RS232) Pin No.
  • Page 54 The ENDAT-3201M Embedded CPU Board Printer (LPT1/LPT2) Port Pin No. Description Pin No. Description STB# ACK# BUSY SLCT AFD# ERR# INIT# SLIN# 18-25 VGA Connector Pin No. Description Pin No. Description N.C. / +5V GREEN BLUE DDC DAT H.Sync V.Sync...
  • Page 55 User’s Manual LCD - LVDS Output Connector (CN5) Pin No. Signal Pin No. Signal Y0– Y2– Y1– Reserved Y3– CK– VDD_PNL DISP_OFF TFT LCD Panel Port Connector (LCD-CON1) Pin No. Signal Pin No. Signal VDDLCD VDDLCD ENPVEE FPD 23 FPD 22 FPD 17 FPD 16 FPD 11...
  • Page 56 The ENDAT-3201M Embedded CPU Board Audio Output Port Connector (CN1) Pin No. Function Pin No. Function BITCLK SDIN N.C. SDIN2 N.C. SDOUT N.C. SYNC –ACRST SPEAK Strapping Low +5V(DC) +12V(DC) JBCY JAB2 JBCX JAB1 JACY JBB2 JACX JBB1 IR Connector (J1)
  • Page 57 User’s Manual IDE1 Connector Pin No. Description Pin No. Description 2,19,22 IDE data2 24.26.30 IDE data13 IDE data1 20,21,28 IDE data14 29,32,34 IDE data0 IDE reset IDE data15 IDE data7 IDE Write IDE data8 IDE Read IDE data6 IDE Ready IDE data9 IDE IRQ IDE data5...
  • Page 58 The ENDAT-3201M Embedded CPU Board Expansion Slot to PCI/ISA Pin Assignment Pin No. Description A Description B Description E Description F –IOCHK RSTDRV –PCINT2 –PCINT4 IRQ9 –PCINT3 –PCINT1 –5V DRQ2 –12V –PCIRST PCLKF +12V –GNT3 IOCHRDY –REQ3 GNT1 –SMEMW SA19 –SMEMR...
  • Page 59 User’s Manual Pin No. Description C Description D Description G Description H –SBHE –MEMCS16 –SERR LA23 –IOSC16 AD15 LA22 IRQ10 –CBE1 AD14 LA21 IRQ11 AD12 LA20 IRQ12 LA19 IRQ13 LA18 IRQ14 LA17 –DACK0 AD13 AD10 –MEMR DRQ0 AD11 –MEMW –DACK5 DRQ5 –CBE0 –DACK6...
  • Page 60 The ENDAT-3201M Embedded CPU Board Appendix C: APM function Operation guide for enable APM function with WIN2000 / WINXP Step1: Click the “Power…” button in “Display Properties” as the picture of below: Step2: Select the “APM” tab in “Power Options Properties” as the picture of below:...
  • Page 61 User’s Manual Step3: Click the check block to enable AMP function as follows:...
  • Page 62 The ENDAT-3201M Embedded CPU Board...

  • Page 63: Appendix C: Limited Warranty

    User’s Manual Appendix D: LIMITED WARRANTY Standard one year limited warranty on all our ENDAT series all-in-one motherboards and embedded board. Products that become defective during the warranty period shall be repaired, or subject to manufacturer’s option, replaced. The limited warranty applies to normal proper usage of the hardware and does not cover products that have been modified or subjected to unusual electrical or physical stress.
  • Page 64 The ENDAT-3201M Embedded CPU Board RMA SERVICE REQUEST FORM When requesting RMA service, please fill out this “RMA Service Request Form”. This form needs to be shipped with your returns. Service cannot begin until we have this information. RMA NO.:...
  • Page 65 User’s Manual Issue Code of defect. Second Times R.M.A. Memory Socket Bad No Screen (No Boot) Hang Up Hardware VGA (Display) Fail Hang Up Software CMOS Data Lost PCB Problem FDC Fail CPU Socket Bad HDC Fail LAN Fail Bad Slot Audio Fail BIOS Problem Serial Port Fail...

Table of Contents