Related Manuals for Graco 1991895
Summary of Contents for Graco 1991895
- Page 1 Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE. OWNER'S MANUAL ©2015 Graco PD294911C 8/15...
- Page 2 Prevent serious injury or death: follow these warnings and the instructions. Failure to follow these warnings and the instructions could result in serious injury or death. Setting Up the Playard • THIS PRODUCT REQUIRES ADULT ASSEMBLY. • Keep fingers clear of top corners during setup. Be sure playard is completely set up before use.
- Page 3 • On soft bedding. NEVER add a mattress, pillow, comforter or padding. Use ONLY mattress pad provided by Graco. • To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.
- Page 4 Parts list This model may not include some features shown below. Check that you have all the parts for this model BEFORE assembling your product. If any parts are missing, call Customer Service. Tools required: Phillips Screwdriver ALL MODELS FEATURES ON CERTAIN MODELS...
- Page 5 Setup DO NOT push center down yet. SNAP!
- Page 6 SNAP! • When setting up, lock rails BEFORE lowering center. Be sure top rails have become rigid. If not, pull up again until they are rigid. If top rails do not latch, lift the center of the floor higher. Hold one end of the unit up and push the center of the floor down.
- Page 7 Always use mattress/pad soft side up.
- Page 8 Put two tabs under mattress/pad through button holes and fasten securely on bottom of unit. Pull strap through bottom of playard and wrap around SNAP! tube and refasten snap. Repeat on other corners.
- Page 9 To Fold Release straps. DO NOT unlock top rails yet. Center of floor must be halfway up before top rails will unlock.
- Page 10 Center of floor must be up. 1. Lift up slightly on the top rail. 2. Push in on the button located on the side of the top rail to release the two tubes. 3. Push down. • If top rails do not unlatch, DO NOT FORCE.
- Page 11 Do not force. If unit will not fold, look for a partially latched top rail. Squeeze the latch button to release the rail.
- Page 12 To Cover Cover unit with handle out. Zip together.
- Page 13 • If a sheet is used with the pad use only the one provided by Graco or one specifically designed to fit the dimensions of the bassinet.
- Page 14 You will need to remove the mattress/pad from the bottom of the playard to use inside your bassinet. 8 Clips NOTE: Bassinet mounts should always be attached on the end with the wheels as shown. Mounts Insert tapered end of bar into end of other bar with hole in it.
- Page 15 Remove 2 screws from back of electronics module. Remove battery door and insert 3-AA (LR06) batteries (not included). Replace door and screws. SNAP!
- Page 17 For Safe Battery Use Keep the batteries out of children’s reach. Any battery may leak battery acid if mixed with a different battery type, if inserted incorrectly (put in backwards) or if all batteries are not replaced or recharged at the same time. Do not mix old and new batteries.
- Page 18 Using Electronics Module The vibration unit may ONLY be used with the bassinet or portable newborn bassinet and napper. WARNING You must remove the module from the unit when your child can pull up to a standing position. TO TURN OFF ANY FUNCTION— Press and hold the button for 2 seconds.
- Page 19 VOLUME— Press the plus (+) to raise the volume and the minus (-) to lower the volume. LIGHTS— Press once to turn top light (A) on, press twice to turn both lights on, press three times to turn bottom light (B) on, and four times to turn lights off.
- Page 20 NATURE SOUNDS— Each press will change to the next nature sound. After the 5th sound is selected, the next press will turn sound off. TIMER— Press once to set timer to 5 minutes, Press twice for 10 minutes, Press 3 times for 15 minutes.
- Page 21 • Always stay within arm’s reach of your child when using the changing table. Never leave child unattended. • The changing table is designed for use only with this Graco playard. Do not use on the floor, bed, counter or other surfaces.
- Page 22 Tubes should appear exactly as shown. Snap leg tubes together as shown. SNAP! Attach short tubes into changing table mounts. Conecte los tubos SNAP!
- Page 23 SNAP! To remove, push in button while pulling up on corner of changing table. Repeat for other side.
- Page 24 Portable Newborn Bassinet & Napper WARNING Prevent serious injury or death: follow these warnings and the instructions. • This product is not intended for unsupervised or prolonged periods of sleep. FALL HAZARD: To prevent falls, stop using the product when infant: •...
- Page 25 • ALWAYS place child on back to sleep. • Use bassinet/napper with only one child at a time. • NEVER place a child under the bassinet/napper. • The bassinet/napper must be fully assembled before using. Do not modify bassinet/napper or add any attachments that are not listed in the owner’s manual.
- Page 26 WARNING • To prevent serious injury or death, DO NOT REMOVE FOAM. • Remove and IMMEDIATELY discard the zip tie. Ziptie When assembling the napper/bassinet, assemble head portion first, then the feet. With the napper side up, insert one of the napper tubes into napper as shown.
- Page 27 Insert the tube into the TOP button housing tube as shown. The metal button should be facing out when snapped in place as shown. CHECK that the webbing attached the napper to the button housing is not twisted. SNAP!
- Page 28 With the napper side up, insert other napper tube into napper as shown. Insert the tube into the other TOP button housing tube as shown. The metal button should be facing out when snapped in place as shown. SNAP!
- Page 29 Open the battery compartment lid by inserting a screwdriver in the slot. Insert one D (LR20) cell battery (not included). Replace lid. Insert one napper tube into top housing tube as shown. The metal button should be facing out when snapped in place as shown.
- Page 30 Insert other napper tube into top housing tube as shown. The metal button should be facing out when snapped in place as shown. SNAP!
- Page 31 Flip over to bassinet side. Attach bassinet tube into housing on both ends of bassinet as shown. The metal button should be SNAP! facing out when snapped in place as shown. SNAP!
- Page 32 Attach bassinet tube into housing on both ends of bassinet as shown. The metal button should be SNAP! facing out when snapped in place as shown. SNAP!
- Page 33 Insert leg into bassinet/napper bassinet as shown. Indent in tube should be facing out. The metal button should be facing out when snapped in SNAP! place as shown. SNAP!
- Page 34 Insert other leg into bassinet/ napper as shown. Indent in tube should be facing out. The metal button should be facing out when snapped in SNAP! place as shown. SNAP!
- Page 35 To keep bassinet/napper from rocking, flip out rock stops. To rock, flip rock stops back in. Using Electronics Module...
- Page 36 To Attach Newborn Bassinet & Napper to bassinet Insert bassinet/napper into mounts on bassinet as shown. CHECK bassinet/napper is secured by pulling up on it.
- Page 37 Newborn Napper® Mode Press button and pull up to unlock and rotate to the napper side. Push down on the inside of napper until it clicks into place. Check that napper is securely attached by pulling up on it. SNAP!
- Page 38 To Secure Child Use slide adjuster at waist for tighter adjustment. To Use Vibration Switch To use integrated vibration switch, slide button to left or right for hi or lo speed. SOOTHING VIBRATION...
- Page 39 Newborn Bassinet Mode Press button and pull up to unlock and rotate to the bassinet side. Push down on the inside of bassinet until it clicks into place. Check that bassinet is securely attached by pulling up on it. SNAP!
- Page 40 To Remove Newborn Bassinet & Napper To remove, press buttons on both sides of the bassinet/ napper handles and pull up as shown.
- Page 41 Accessories (certain models) This model may not include some features shown Mobile WARNING • Possible entanglement injury. Keep out of baby’s reach. Remove mobile from crib or playpen when baby begins to push up on hands and knees. Recommended use from birth to 5 months. •...
- Page 42 Open the battery compartment lid by inserting a screwdriver in the slot. Insert 3-AA (LR06) batteries (not included). Replace lid.
- Page 43 Press button down to turn mobile ON, up to turn OFF.
- Page 44 Press button and lift up to remove.
- Page 45 Parent Organizer WARNING Always keep objects out of child’s reach. Remove this accessory when child is able to pull himself up in the playard.
- Page 46 Care and Maintenance FROM TIME TO TIME CHECK YOUR PLAYARD for worn parts, torn material or stitching. Replace or repair the parts as needed. Use only Graco replacement parts. ® IF PLAYARD IS USED AT THE BEACH, you MUST clean sand off your playard, including the feet, before packing it into cover.
- Page 47 WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.