Related Manuals for HPE Apollo pc40
Summary of Contents for HPE Apollo pc40
-
Page 1: User Guide
HPE Apollo pc40 Server User Guide Abstract: This guide provides an overview of the HPE Apollo pc40 server. Part Number: 007-6488-001 Published: September 2017 Edition: Revision 1... - Page 2 2017, Hewlett Packard Enterprise Development LP © Notices The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
-
Page 3: About This Manual
Preface About this Manual This manual provides a brief summary of the HPE Apollo pc40 server. The HPE Apollo pc40 server is a 1U dual socket server featuring up to four NVIDIA® Tesla® GPUs and based on the Intel® Xeon® Processor Scalable Family. The HPE Apollo pc40 Server is an optimized, industry-standard server for deep learning and high performance computing (HPC) workloads that uses the PCIe form factor for greater choice in GPU selection. -
Page 4: Table Of Contents
Contents Chapter 1 Introduction 1.1 Overview ..........................6 1.2 Unpacking the System ......................6 1.3 System Features ........................9 1.4 Server Chassis Features ......................9 Control Panel ........................9 1.5 Motherboard Layout ......................12 Quick Reference Table ......................13 Chapter 2 Server Installation 2.1 Overview ..........................15 2.2 Preparing for Setup ......................15 Choosing a Setup Location ....................15 Rack Precautions ......................15 Server Precautions ......................16... - Page 5 Chapter 3 Maintenance and Component Installation 3.1 Removing Power ........................25 3.2 Accessing the System ......................25 3.3 Chassis Hard Drives ......................27 Externally Accessible Drives ..................27 Internal Drives ........................28 Power Supply ........................29 Replacing a Power Supply Module ................29 Appendix A BIOS Error Codes and System Specifications...
-
Page 6: Chapter 1 Introduction
1.2 Unpacking the System Inspect the box the HPE Apollo pc40 server was shipped in and note if it was damaged in any way. If any equipment appears damaged, please file a damage claim with the carrier who delivered it. - Page 7 The illustrations below provide an overview of the front and rear features of the HPE Apollo pc40 server. The following page shows a top view of the system. Front View Item Description HPE Apollo pc40 Chassis (1U) 2 SFF Hot-swap SATA Drive Bays...
- Page 8 Top View Item Description Full-height/Full-length PCIe 3 x16 slots for GPUs DIMMs for processor 1 Processor 1 Full-height/Full-length PCIe Gen3 x16 slot Processor 2 DIMMs for processor 2...
-
Page 9: System Features
1.3 System Features For a complete list of system features, please refer to the HPE Apollo pc40 QuickSpecs at: www.hpe.com/servers/apollo-pc40 1.4 Server Chassis Features Control Panel The switches and LEDs located on the control panel are described below. Control Panel View... -
Page 10: Information Led
Remote UID is on. Use this function to identify the Blinking blue server from a remote location. Note: The HPE Apollo pc40 server is only considered to be N+1 in the 200-240V range; the 100-127V range requires both power supplies to be operating. - Page 11 RSC-G-A66-X1 CPU1 AOM-SXM-BRG AOM-SXM2 MBD-X11DGQ CPU2 AOM-SXM-BRG NVLINK – Additional VOLTA Links NVLINK – PASCAL RSC-GN2-66 PCIE 3.0 SXM2 Add-on Module Block Diagram Note: Volta NVLINKs will become available at a later date.
-
Page 12: Motherboard Layout
1.5 Motherboard Layout Below is a layout of the HPE Apollo pc40 server motherboard with jumper, connector and LED locations shown. See the table on the following page for descriptions. JBT1 JTPM1 JSDCARD1 X11DGQ JPSU2 JPSU1 REV:1.00 DESIGNED IN USA... -
Page 13: Quick Reference Table
Quick Reference Table Jumper Description Default Setting JBT1 Clear CMOS JPME2 ME ManufactureMode Pins 1-2 (Normal) Pins JVRM1/JVRM2 I2C Bus for VRM 1-2 (BMC: Normal) Pins JWD1 Watch Dog Timer Enable 1-2 (Reset) Connectors Description Battery (BT1) Onboard CMOS Battery FAN8/FAN9 CPU/System Cooling Fan Headers FAN_CTRL... - Page 14 Debug Card SYSTEM POWER BIOS FAN SPEED CTRL Intel PCH C621 Chipset: System Block Diagram Note: This is a general block diagram and may not exactly represent the features on your motherboard. See the QuickSpecs at www.hpe.com/servers/apollo-pc40 for additional information.
-
Page 15: Chapter 2 Server Installation
Chapter 2 Server Installation 2.1 Overview This chapter provides advice and instructions for mounting your system in a server rack. Caution: Electrostatic Discharge (ESD) can damage electronic components. To prevent such damage to PCBs (printed circuit boards), it is important to use a grounded wrist strap, handle all PCBs by their edges and keep them in anti-static bags when not in use. -
Page 16: Server Precautions
• In single rack installations, stabilizers should be attached to the rack. In multiple rack in- stallations, the racks should be coupled together. • Always make sure the rack is stable before extending a server or other component from the rack. •... -
Page 17: Circuit Overloading
Circuit Overloading Consideration should be given to the connection of the equipment to the power supply circuitry and the effect that any possible overloading of circuits might have on overcurrent protection and power supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. -
Page 18: Installing The Rails
2.3 Installing the Rails This section provides information on installing the chassis into a rack unit with the rails provided. There are a variety of rack units on the market, which may mean that the assembly procedure will differ slightly from the instructions provided. You should also refer to the installation instructions that came with the rack unit you are using. -
Page 19: Releasing The Inner Rail
Releasing the Inner Rail To mount the rail onto the chassis, first release the inner rail from the outer and middle rails. Releasing the Inner Rail from the Middle and Outer Rails 1. Lift the auto-lock latch and pull the inner rail until it is fully extended. 2. -
Page 20: Installing The Inner Rails On The Chassis
Installing The Inner Rails on the Chassis Installing the Inner Rails 1. Identify the left and right inner rails. 2. Place the inner rail firmly against the side of the chassis, aligning the T-studs on the side of the chassis with the slotted holes in the inner rail. 3. -
Page 21: Installing The Outer Rails On The Rack
Installing the Outer Rails on the Rack Installing the Outer Rails 1. Confirm that the left and right outer rails have been correctly identified 2. Release the small locking lever on the inside of the middle rail and push the middle rail back into the outer rail. -
Page 22: Installing The System Into The Rack
Installing the System into the Rack After the rails are installed on the chassis and on the rack, the server can be installed in the rack. Be sure to use sufficient personnel to lift it safely. Installing the Chassis into a Rack 1. -
Page 23: Removing The System From The Rack
Removing the System From the Rack 1. Lift the auto-lock latches and pull the chassis out the front of the rack until it stops. 2. To remove the chassis from the rack completely, press the release latches on each of the inner rails downward simultaneously and continue to pull the chassis out of the rack. -
Page 24: Removing The Outer Rails From The Rack
Removing the Outer Rails From the Rack In the uncommon event that it is necessary to remove the outer rails from the rack, follow these instructions. The chassis must be out of the rack. Releasing the Outer Rails 1. On the front of the outer rail, slide the small plastic safety slider (red in drawing) up and hold it while pushing the plastic release button (green in drawing) just below it. -
Page 25: Chapter 3 Maintenance And Component Installation
3. Disconnect the power cord(s) from the power supply module(s). 3.2 Accessing the System The HPE Apollo pc40 server features a removable two-piece top cover, which allows easy access to the inside of the chassis. Removing the Top Cover 1. - Page 26 Removing the Chassis Cover...
-
Page 27: Chassis Hard Drives
3.3 Chassis Hard Drives The HPE Apollo pc40 server has two externally accessible hot-swap 2.5" drive bays and space for two internal fixed 2.5" drives.. The hard drives are mounted in drive carriers to simplify their installation and removal from the chassis. -
Page 28: Internal Drives
Internal Drives The system supports one or two 2.5" fixed hard disk drives when using the included mounting bracket. Installing Internal Drives 1. Begin by removing power from the system as described in Section 3.1. 2. Remove the chassis cover as described in Section 3.2. 3. -
Page 29: Power Supply
5. Plug the AC power cord back into the unit and power up the server. Removing/Replacing a Power Supply Note: The HPE Apollo pc40 server is only considered to be N+1 in the 200-240V range; the 100-127V range requires both power supplies to be operating. -
Page 30: Appendix A Bios Error Codes And System Specifications
If the computer cannot complete the boot process, a diagnostic card can be attached to the computer to read I/O port 0080h. System Specifications System specifications for your HPE Apollo pc40 server can be found in the QuickSpecs document. Refer to www.hpe.com/servers/apollo-pc40... - Page 31 Websites General websites Hewlett Packard Enterprise Information Library www.hpe.com/info/EIL Single Point of Connectivity Knowledge (SPOCK) Storage www.hpe.com/storage/spock compatibility matrix Storage white papers and analyst reports www.hpe.com/storage/whitepapers For additional websites, see Support and other resources.
-
Page 32: Support And Other Resources
IMPORTANT: Access to some updates might require product entitlement when accessed through the Hewlett Packard Enterprise Support Center. You must have an HPE Passport set up with relevant entitlements. Customer self repair Hewlett Packard Enterprise customer self repair (CSR) programs allow you to repair your product. If a CSR part needs to be replaced, it will be shipped directly to you so that you can install it at your convenience. -
Page 33: Warranty Information
To view the warranty for your product, see the Safety and Compliance Information for Server, Storage, Power, Networking, and Rack Products document, available at the Hewlett Packard Enterprise Support Center: www.hpe.com/support/Safety-Compliance-EnterpriseProducts Additional warranty information HPE ProLiant and x86 Servers and Options www.hpe.com/support/ProLiantServers-Warranties HPE Enterprise Servers www.hpe.com/support/EnterpriseServers-Warranties HPE Storage Products www.hpe.com/support/Storage-Warranties... -
Page 34: Documentation Feedback
Documentation Feedback (docsfeedback@hpe.com). When submitting your feedback, include the document title, part number, edition, and publication date located on the front cover of the document. For online help content, include the product...