Protection Devices; Arrest Functions; Safe Use; Residual Risks - lavina 20n-x User Manual

Superabrasive
The protection devices are working properly.
The electrical cable is free to follow the machine easily. In order
to keep the electrical cable from being damaged, no vehicle
should cross the zone where electrical cables are situated.
PROTECTION DEVICES
The machine is equipped with
several protection devices including the following:
An emergency stop button
A protection skirt and hood for protecting the tool plates.
These devices protect the operator and/or other persons from
potential injuries. Do not remove them. On the contrary, before
using the machine, please ensure that all protection devices are
mounted and function properly. The Security plate prevents the
QuickChange pads from loosening during use.
ARREST FUNCTIONS
Methods of arresting the machine
are the following:
Button to stop the motor (category 1)
Emergency stop button (category
SAFE USE
The LAVINA® X is designed to
minimize all risks correlated with its use. However, it is not
possible to fully eliminate the risks of an accident with the
machine. An unskilled or uninstructed operator may cause
correlated residual risks. Such risks are:
Position Risks due to operator's incorrect working position
Entanglement Risks due to wearing inappropriate working
clothes
Training Risks due to lack of operational training
NOTE: In order to reduce any consequences of the above‐
mentioned risks, we advise that machine operators follow the
instructions in the manual at all times.
RESIDUAL RISKS
During the normal operating
and maintenance cycles, the operator is exposed to few residual
risks, which cannot be eliminated due to the nature of the
operations.
BEFORE YOU BEGIN
Working area must be clear
from any debris or objects.
A first‐time operator must always read the manual and pay
attention to all safety instructions.
All electric connections and cables must be inspected for
potential damages.
Ground wire system of the power supply must be also inspected.
Perform general daily inspections of the machine and inspect
the machine before each use.
Always inspect the safety devices: Mount the Security plate for
the Quickchange pads.
The emergency break must be clear and working
The tool protector must be working
The machine must be clean
Never operate the machine in the rain!
User Manual Original Language Lavina® 20N‐X
Confirm that there are no missing parts especially after
transportation, repair, or maintenance.
Before filling the water tank with water make sure the machine is
not working and the main switch is turned off.
Before turning on the machine make sure that the base is placed on
the floor, the machine MUST NOT be in an upright
position when turned on!
OPERATING MACHINE
When operating the LAVINA® X, make certain that there is no
one, but you around the machine.
Never leave the machine unattended while working.
The electrical cable must move freely and must be damage‐free.
The water hose must move freely and must be damage‐free.
Check the floor you will work on to make sure it is not too uneven.
If this is the case, it may damage the machine.
AFTER WORK IS COMPLETED
Clean the machine and its
surroundings properly
Empty and clean the water tank
1)
Unplug the machine and wind up the electrical cable
Store the machine in a safe place
THE WORK AREA
Make certain that people or
vehicles do not enter the work area.
Clear paths of hoses or cables.
Always check the floor for debris
PERSONAL PROTECTIVE
EQUIPMENT (PPE)
Always wear safety shoes when working with the machine.
Always wear ear protectors
when working with the
machine.
All personnel in the immediate work area must wear safety
glasses with side shields.
Always wear safety gloves when changing the tools. Always
wear clothes suitable for the work environment.
OPERATOR
The operator must know the machine's work environment.
Only one operator at a time can work with the machine. The
operator must be properly trained and well instructed prior
operating the machine.
The operator must understand all the instructions in this
manual.
The operator must understand and be able to interpret all the
drawings and designs in manual.
The operator must know all sanitation and safety regulations
pertaining to the operation of the machine.
The operator must have floor grinding experience.
The operator must know what to do in case of emergency.
The operator must have an adequate technical knowledge and
preparation.
7
6/2017