1. Manuals
  2. Brands
  3. IN-COMMAND Manuals
  4. Control Systems
  5. JRVCS2
  6. Installation and operation manual

IN-COMMAND JRVCS2 Installation And Operation Manual

Rv control and monitoring system
Hide thumbs
Table of Contents

Advertisement

Quick Links

JRVCS2
RV CONTROL AND MONITORING SYSTEM
Installation and Operation Manual

Advertisement

Table of Contents
loading

Related Manuals for IN-COMMAND JRVCS2

Summary of Contents for IN-COMMAND JRVCS2

  • Page 1 JRVCS2 RV CONTROL AND MONITORING SYSTEM Installation and Operation Manual...

  • Page 3: Important Safety Information

    Important Safety Information Read the iN-Command Manual, and these warnings and instructions carefully before using this product. Failure to follow the use instructions in this owner’s manual, or improper use of the Mobile Application, Display Commander and/or Body Control Module, could result in personal injury, including death.

  • Page 4: Table Of Contents

    JRVCS2 • TABLE OF CONTENTS TABLE OF CONTENTS ............3 MOBILE DEVICES: ..................18 INTRODUCTION ..............4 Pairing Mobile Device to DC ............... 19 Thank You! ................4 CHECKING ACTIVE BLUETOOTH SESSION* ........... 24 Features .................4 SOFTWARE UPDATE* ................. 25 Precautions ................4 RESET: FLOOR PLAN ................. 28 Packing List ................4...

  • Page 5: Introduction

    • Thank You! The front of this unit should only be cleaned with a slightly damp cloth. Thank you for choosing a iN-Command product. We hope you will fi nd Do not use cleaning products. the instructions in this owner’s manual clear and easy to follow. If you •...

  • Page 6: Installation

    • Check and ensure correct operation • Tools and Supplies • Mount the unit using four #8 PH (0.164” x 0.75”) screws You will need these tools and supplies to install your iN-Command: • Attach Trim ring • Phillips screwdriver •...

  • Page 7: Wiring

    JRVCS2 • WIRING The wiring diagram depicts all the wiring connections required for proper operation of the unit. BODY CONTROL MODULE (BCM) CONNECTIONS PIN NO. WIRE GAUGE DESCRIPTION PIN NO. WIRE GAUGE DESCRIPTION PIN NO. WIRE GAUGE DESCRIPTION 18 AWG...

  • Page 8: Setup Menu List

    JRVCS2 • SETUP MENU LIST ITEM SELECTION Trigger 2 No, Momentary, Latch Generator No, Propane, Gasoline Trigger 3 No, Momentary, Latch Fuel Station No, Yes Trigger 4 No, Momentary, Latch Fresh Water Tank 2 No, Yes Alarm 1 +12V Input...

  • Page 9: Safety Lockout

    JRVCS2 • SAFETY LOCKOUT iN-Command is equipped with a Safety Lockout feature to ensure certain system functions are unavailable during transit. When the Brake Signal on the tow vehicle is activated, the iN-Command will lock down all motorized functions. The Display Commander and mobile devices will also display “Travel Lock On”...

  • Page 10: Override Switches

    JRVCS2 • OVERRIDE SWITCHES The Body Control Module has a bank of override switches. The rotary switches below each rocker switch correspond to an electric function* made by the Display Commander. The left switch controls the awning and jacks. The right switch controls the slides.

  • Page 11: Specifications

    This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may JRVCS2 System cause harmful interference to radio communications. EPROM Non-Volatile Memory ..... . YES However, there is no guarantee that interference will not occur in a Bluetooth Version .

  • Page 12: Passcode Protection

    JRVCS2 • PASSCODE PROTECTION A passcode is required to access the system. On the fi rst time use of the system, the user is required to Confi rm the new passcode. enter and confi rm a new passcode.

  • Page 13: Menu

    • Change the passcode • Reset the fl oor plan • Control the brightness of the DC screen • And view iN-Command’s legal documents and customer support information 3. A device rename window will open. Press “OK” after completing the The Setup button is used by the manufacturer.

  • Page 14: Scroll List Editing

    Light Groups can be added to the system. “Electric Slide 1” is shown as an example. * The iN-command system supports multiple functions. Functions can be added, but will require modifi cation and or addition of external components, wiring, and plumbing.

  • Page 15: Slides

    JRVCS2 • Slides • Jacks Jacks can be added to the system. Slides can be added to the system. • Triggers Triggers can be added to the system. “Momentary” or “Latch” can • Awnings be selected for each Trigger. Note: Desired devices need to be Awnings can be added to the system.

  • Page 16: Passcode

    JRVCS2 • Passcode 1. Select “Menu”. 2.1 Enter the correct passcode to proceed. 3. The passcode setup window will open. 2. Press “Passcode” to enter passcode setup.
  • Page 17 JRVCS2 3.1 Passcode protection may be eisabled or enabled by selecting Change Enabled or Disable. Enabled mode Disabled mode...

  • Page 18: Set Passcode Timer

    JRVCS2 • Set Passcode Timer Press the “Set Timer” button to select the idle time to 3. Confi rm new passcode. activate the passcode protection. • Change Passcode • Clear Passcode 1. Press the “Change Passcode” button to change to a new Press the “Clear Passcode”...

  • Page 19: Mobile Devices

    JRVCS2 • MOBILE DEVICES: iN-Command is able to pair to Android and iOS devices using the iN-Command App. Visit the Google Play and Apple App stores on your mobile device to check compatibility of your device. Seven mobile devices are able to be paired to iN-Command at one time, but only 1 iOS and 3 Android devices are able to be actively paired;...

  • Page 20: Pairing Mobile Device To Dc

    JRVCS2 • Pairing Mobile Device to DC 1.3 Currently, it shows no BT paired device connected to this DC. 1. On the DC: Press the “Discover” button to activate the BT pairing mode. 1.1 Select “Menu”. 1.2 Select “Bluetooth”. 1.4 Press “Allow”.
  • Page 21 JRVCS2 2. Android Mobile Device Pairing Steps: 2.2 The Mobile APP will scan for the DC 2.3 The DC will be displayed in the Unpaired 2.1 Press “Bluetooth” on the “Setup” device. Devices list in the format page to fi nd the DC device.
  • Page 22 JRVCS2 3. Apple Mobile Device Pairing Steps: 2.4 On the DC, a request message will appear. Press “Pair” Enable “Bluetooth” in the system settings of Apple mobile device. to start the BT pairing and concurrently enter the same passkey on the Mobile device.
  • Page 23 JRVCS2 Press “Pair” in DC. The DC will be displayed in the MY DEVICES list in the format “JENSENDCXXXXXX”. Press the DC device to connect with it. Press “Pair” in Apple mobile device. The Apple mobile device now shows the DC is connected.
  • Page 24 JRVCS2 4. Reset Floor Plan Press the “Reset” button in the Menu page to load the fl oor plan confi guration from the DC. The current settings will be lost/replaced.

  • Page 25: Checking Active Bluetooth Session

    JRVCS2 • CHECKING ACTIVE BLUETOOTH SESSION* 1. Select “Status”. * Unless there is a communication issue with the handheld device, there should be no reason to check the Bluetooth session. 2. The page shows information of current active Bluetooth devices.

  • Page 26: Software Update

    JRVCS2 • SOFTWARE UPDATE* Software updates include fl oorplan redesigns and app version updates. 3. Enter engineer passcode to proceed.** 1. Select “Menu” and insert USB drive into the DC USB port. 2. Select “Setup”...
  • Page 27 - File name: “JRVCS2-CM Vxxxx.bin” → BCM update, (xxxx is version number) - File name: “JRVCS2-DC Vxxx.zip” → DC Android OS update - File name: “xxxxxx.xml” → Floor Plan update 5. The system must be updated in the following order to prevent loss of communication between the DC and BCM.
  • Page 28 JRVCS2 5.4 Press “OK” to confi rm selection 5.3 Press the APP Version “Update” button to update DC APP. * If a software update is needed, go to 5.4 Press the Floor Plan “Select” button to select and www.asaelectronics.com/in-command load the new fl oor plan.

  • Page 29: Reset: Floor Plan

    JRVCS2 • RESET: FLOOR PLAN 3. Select “Reset” to restore the system to previous setting. To reset the fl oor plan to remove customization, select “Menu”. 3. Select one of the two options to restore to a previous state. Current settings will be lost.

  • Page 30: System Calibration

    JRVCS2 • SYSTEM CALIBRATION 3. Enter engineer passcode to proceed.** 1. Select “Menu”. 2. Select “Setup”. 4. Select “Enter” corresponding to Admin.
  • Page 31 JRVCS2 6. Select “Tanks” to set resistor reference value for every tank. 5. Enter admin passcode to proceed.** 5.1 Make Selection. * The system should be calibrated by the manufacturer and only need to be accessed for troubleshooting. ** The Engineering and Admin Passcode is used by the manufacturer for programming and troubleshooting purposes.

  • Page 32: Auto Generator Start

    JRVCS2 • AUTO GENERATOR START 3. If the generator is started, the system will run the generator for 1. Press the "Auto" button to activate AUTO GEN START. 60 minutes. 2. If the battery voltage is less than 11.8 volts for 3 minutes 4.

  • Page 33: Troubleshooting

    JRVCS2 • TROUBLESHOOTING Symptom Solution Try cycling power with the ON/OFF button. Display Commander (DC) will Check main fuse in Distribution Panel. not turn ON or no front panel Check 12V+ on wire to DC (RED wire). operation Check Ground wire to DC.
  • Page 34 JRVCS2...
  • Page 36 ASA Electronics LLC. www.asaelectronics.com www.jensenrvdirect.com ©2016 ASA Electronics LLC. MA-1605001-1R...

Table of Contents