Configuring The Controller Of Channelized T3/T1 Interfaces; Verifying The Controller Configuration Of Channelized T3/T1 Interfaces; 1 Port Oc48/ 4 Port Oc12/Oc3 + 12 Port T1/E1 + 4 Port T3/E3 Cem Interface Module Configuration Guide, Cisco - Cisco ASR 900 Series Configuration Manual

Configuring T3 Interfaces

Configuring the Controller of Channelized T3/T1 Interfaces

98 Unavailable Secs, 14 Line Errored Secs,
7 C-bit Errored Secs, 7 C-bit Severely Errored Secs
0 Severely Errored Line Secs
0 Far-End Errored Secs, 0 Far-End Severely Errored Secs
0 CP-bit Far-end Unavailable Secs
0 Near-end path failures, 0 Far-end path failures
0 Far-end code violations, 0 FERF Defect Secs
0 AIS Defect Secs, 0 LOS Defect Secs
Configuring the Controller of Channelized T3/T1 Interfaces
When the channelized T3/T1 interface is used for the first time, the running configuration does not show the
T3 controller. You can use the show platform command to check if the chassis recognizes the T3 port and
initializes the card properly. After the port is configured for the slot, the respective controller appears in the
running configuration and you can configure the channelized T3/T1 interface.
Perform this task to configure channelized controller as T3/T1.
enable
configure terminal
controller t3 0/4/12
channelized
clock source line
no shut
exit
The channelized mode is the default mode for T3 interface.
Note

Verifying the Controller Configuration of Channelized T3/T1 Interfaces

Use the show controllers command to verify the controller configuration of channelized T3/T1 interfaces:
# show controllers t3 0/4/12
T3 0/4/12 is down.
Hardware is A900-IMA3G-IMSG
Applique type is Channelized T3/T1
Receiver has loss of signal.
MDL transmission is disabled
FEAC code received: No code is being received
Framing is C-BIT Parity, Line Code is B3ZS, Cablelength Short less than 225ft
BER thresholds: SF = 10e-10 SD = 10e-10
Clock Source is line
Equipment customer loopback
Data in current interval (730 seconds elapsed):
0 Line Code Violations, 0 P-bit Coding Violation
0 C-bit Coding Violation, 0 P-bit Err Secs
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
0 Unavailable Secs, 730 Line Errored Secs
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
0 Severely Errored Line Secs
0 Far-End Errored Secs, 0 Far-End Severely Errored Secs
0 CP-bit Far-end Unavailable Secs
0 Near-end path failures, 0 Far-end path failures
0 Far-end code violations, 0 FERF Defect Secs
0 AIS Defect Secs, 0 LOS Defect Secs
Data in Interval 1:
0 Line Code Violations, 0 P-bit Coding Violation
0 C-bit Coding Violation, 0 P-bit Err Secs
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
0 Unavailable Secs, 900 Line Errored Secs
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
0 Severely Errored Line Secs
0 Far-End Errored Secs, 0 Far-End Severely Errored Secs
1 port OC48/ 4 port OC12/OC3 + 12 port T1/E1 + 4 port T3/E3 CEM Interface Module Configuration Guide, Cisco IOS
XE Fuji 16.7.x (Cisco ASR 900 Series)
25