ABB RED615 Product Manual page 47

ABB
Line Differential Protection and Control
RED615
Product version: 2.0
The communication module harware determines the available communication protocols. Choose
the digits from one of the blue communication rows below to define the corect digits for digits 9-11.
Note that the communication options are not dependant on the chosen standard configuration.
# DESCRIPTION
9 Communication descriptions in short:
Substation communication (serial) options #9
-
Protection and substation communication (Ethernet) options #10
11
Communication protocol options #11
Serial Ethernet
options options
# 9 # 10
A = A =
RS-485 Line differential, multi mode
(incl. IRIG-B) fibre (LC)
or
B =
Line differential, single mode
fibre (LC)
A = G =
RS-485 Ethernet 100Base TX (RJ-45)
(incl. IRIG-B)
and line differential, multi mode
fibre (LC)
or
H =
Ethernet 100Base TX (RJ-45)
and line differential, single mode
fibre (LC)
or
J =
2 x Ethernet 100Base TX (RJ-45)
and line differential, multi mode
fibre (LC)
or
K =
2 x Ethernet 100Base TX (RJ-45)
and line differential, single mode
fibre (LC)
B = A =
Glass Line differential, multi mode
fibre (ST fibre (LC)
or
Rx/Tx, incl.
B =
IRIG-B) Line differential, single mode
fibre (LC)
B = G =
Glass Ethernet 100Base TX (RJ-45)
fibre (ST
and line differential, multi mode
Rx/Tx, incl. fibre (LC)
or
IRIG-B)
H =
Ethernet 100Base TX (RJ-45)
and line differential, single mode
fibre (LC)
or
J =
2 x Ethernet 100Base TX (RJ-45)
and line differential, multi mode
fibre (LC)
or
K =
2 x Ethernet 100Base TX (RJ-45)
and line differential, single mode
fibre (LC)
N = A =
None Line differential, multi mode
fibre (LC)
or
B =
Line differential, single mode
fibre (LC)
N = G =
None Ethernet 100Base TX (RJ-45)
and line differential, multi mode
fibre (LC)
or
H =
Ethernet 100Base TX (RJ-45)
and line differential, single mode
fibre (LC)
or
J =
2 x Ethernet 100Base TX (RJ-45)
and line differential, multi mode
fibre (LC)
or
K =
2 x Ethernet 100Base TX (RJ-45)
and line differential, single mode
fibre (LC)
In addition to a serial communication option for station bus communication to gateways and SCADA systems, an Ethernet communication
option can be chosen. This enables the use of an Ethernet based service bus for PCM600 and the WebHMI. However, this requires that an
Ethernet communication option is chosen in addition to the serial communication (digit #10 = RJ-45 or LC).
H B D C A C A D
Protocol
options
# 11
B =
Modbus
or
D =
IEC 60870-5-103
or
E =
DNP3
A =
IEC 61850
or
B =
Modbus
or
C =
IEC 61850 and Modbus
or
D =
IEC 60870-5-103
or
E =
DNP3
B =
Modbus
or
D =
IEC 60870-5-103
or
E =
DNP3
A =
IEC 61850
or
B =
Modbus
or
C =
IEC 61850 and Modbus
or
D =
IEC 60870-5-103
or
E =
DNP3
A =
IEC 61850
A =
IEC 61850
or
B =
Modbus
or
C =
IEC 61850 and Modbus
or
D =
IEC 60870-5-103
or
E =
DNP3
1MRS756500 B
Issued: 03.07.2009
A B B 1 A A N 1 X C
47