IEI Technology WSB-H810 User Manual
  1. Manuals
  2. Brands
  3. IEI Technology Manuals
  4. Motherboard
  5. WSB-H810
  6. User manual

IEI Technology WSB-H810 User Manual

Full-size picmg 1.0 cpu card supports lga1150 intel core i7/i5/i3, pentium and celeron cpu per intel h81, ddr3, vga/idp, dual intel gbe, usb 3.0, sata 6gb/s, pcie mini, msata, rs-232, hd audio and rohs
Hide thumbs
Table of Contents

Advertisement

Quick Links

WSB-H810 PICMG 1.0 CPU Card
MODEL:
WSB-H810
Full-Size PICMG 1.0 CPU Card Supports 4th Generation
LGA1150 Intel® Core™ i7/i5/i3, Pentium® or Celeron® CPU,
Intel® H81 Chipset, DDR3, VGA, iDP, Dual Intel® GbE, USB 3.0,
SATA 6Gb/s, PCIe Mini, mSATA, RS-232, HD Audio and RoHS

User Manual

Page i
Rev. 1.02 – May 5, 2017

Advertisement

Table of Contents
loading

Related Manuals for IEI Technology WSB-H810

Summary of Contents for IEI Technology WSB-H810

  • Page 1: User Manual

    WSB-H810 PICMG 1.0 CPU Card MODEL: WSB-H810 Full-Size PICMG 1.0 CPU Card Supports 4th Generation LGA1150 Intel® Core™ i7/i5/i3, Pentium® or Celeron® CPU, Intel® H81 Chipset, DDR3, VGA, iDP, Dual Intel® GbE, USB 3.0, SATA 6Gb/s, PCIe Mini, mSATA, RS-232, HD Audio and RoHS...
  • Page 2 WSB-H810 PICMG 1.0 CPU Card Revision Date Version Changes May 5, 2017 1.02 Modified the part number and description of the optional LPT cable June 16, 2015 1.01 Added two RS-232 serial ports March 10, 2015 1.00 Initial release Page ii...
  • Page 3 WSB-H810 PICMG 1.0 CPU Card Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.
  • Page 4 WSB-H810 PICMG 1.0 CPU Card Manual Conventions WARNING Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. CAUTION Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product.

  • Page 5: Table Of Contents

    WSB-H810 PICMG 1.0 CPU Card Table of Contents 1 INTRODUCTION......................1 1.1 I ......................2 NTRODUCTION 1.2 F ........................3 EATURES 1.3 C ......................4 ONNECTORS 1.4 D ....................... 5 IMENSIONS 1.5 D ........................ 7 1.6 T ..................8 ECHNICAL PECIFICATIONS 2 PACKING LIST ......................11...
  • Page 6 WSB-H810 PICMG 1.0 CPU Card 3.2.11 Front Panel Connector................... 28 3.2.12 I C Connector ....................29 3.2.13 Infrared Connector (Reserved) ..............30 3.2.14 Internal DisplayPort Connector ..............30 3.2.15 Keyboard and Mouse Connector ..............31 3.2.16 LAN LED Connectors ..................32 3.2.17 mSATA Slot.....................
  • Page 7 WSB-H810 PICMG 1.0 CPU Card 4.9.1 AT/ATX Power Mode Setting ................64 4.9.2 Clear CMOS Button..................65 4.9.3 Flash Descriptor Security Override..............65 4.9.4 USB Power Selection ..................66 4.10 C ..................67 HASSIS NSTALLATION 4.10.1 Airflow......................67 4.10.2 CPU Card Installation ................... 67 4.11 I...
  • Page 8 WSB-H810 PICMG 1.0 CPU Card 5.4.1.1 PCI Express Configuration ..............101 5.4.1.2 PCH Azalia Configuration ..............103 5.4.2 System Agent (SA) Configuration ..............104 5.4.2.1 Graphics Configuration................104 5.4.2.2 NB PCIe Configuration................107 5.4.2.3 Memory Configuration ................108 5.5 B ........................
  • Page 9 WSB-H810 PICMG 1.0 CPU Card List of Figures Figure 1-1: WSB-H810 ........................2 Figure 1-2: Connectors ........................4 Figure 1-3: WSB-H810 Dimensions (mm)..................5 Figure 1-4: External Interface Panel Dimensions (mm) ..............6 Figure 1-5: Data Flow Diagram......................7 Figure 3-1: Connectors and Jumpers..................18 Figure 3-2: +12V Power Connector Pinout Location ..............21 Figure 3-3: ATX Power Supply Enable Connector Location ............22...
  • Page 10 WSB-H810 PICMG 1.0 CPU Card Figure 3-26: SPI Flash Connector Location................42 Figure 3-27: SPI EC Flash Connector Location.................43 Figure 3-28: TPM Connector Location..................43 Figure 3-29: USB 2.0 Connector Pinout Locations ..............44 Figure 3-30: USB 2.0 Connector (Type A) Pinout Location............45 Figure 3-31: USB 3.0 Connector Location .................46...
  • Page 11 WSB-H810 PICMG 1.0 CPU Card Figure 6-6: Graphics Driver InstallShield Wizard ..............118 Figure 6-7: Graphics Driver – Extracting Files ............... 119 Figure 6-8: Graphics Driver Welcome Screen ................ 119 Figure 6-9: Graphics Driver License Agreement..............120 Figure 6-10: Graphics Driver Read Me File ................120 Figure 6-11: Graphics Driver Setup Progress ................
  • Page 12 WSB-H810 PICMG 1.0 CPU Card List of Tables Table 1-1: WSB-H810 Specifications ..................10 Table 2-1: Packing List.........................13 Table 2-2: Optional Items......................16 Table 3-1: Peripheral Interface Connectors ................20 Table 3-2: Rear Panel Connectors ....................20 Table 3-3: +12V Power Connector Pinouts ................21 Table 3-4: ATX Power Supply Enable Connector Pinouts ............22...
  • Page 13 WSB-H810 PICMG 1.0 CPU Card Table 3-28: SPI Flash Connector Pinouts ..................42 Table 3-29: SPI EC Flash Connector Pinouts ................43 Table 3-30: TPM Connector Pinouts ...................44 Table 3-31: USB 2.0 Connector Pinouts ..................45 Table 3-32: USB 2.0 Connector (Type A) Pinouts ..............45 Table 3-33: USB 3.0 Connector Pinouts ..................46...
  • Page 14 WSB-H810 PICMG 1.0 CPU Card BIOS Menus BIOS Menu 1: Main ........................73 BIOS Menu 2: Advanced ......................75 BIOS Menu 3: ACPI Configuration ....................75 BIOS Menu 4: RTC Wake Settings ....................76 BIOS Menu 5: TPM Configuration ....................78 BIOS Menu 6: CPU Configuration ....................79 BIOS Menu 7: SATA Configuration .....................81...

  • Page 15: Introduction

    WSB-H810 PICMG 1.0 CPU Card Chapter Introduction Page 1...

  • Page 16: Introduction

    WSB-H810 PICMG 1.0 CPU Card 1.1 Introduction Figure 1-1: WSB-H810 The WSB-H810 PICMG 1.0 CPU card is a Socket LGA1150 Intel® Core™ i7/i5/i3, Pentium® or Celeron® processor platform that supports two 240-pin 1600/1333 MHz dual-channel DDR3/DDR3L DIMMs up to 16 GB.

  • Page 17: Features

    WSB-H810 PICMG 1.0 CPU Card 1.2 Features Some of the WSB-H810 motherboard features are listed below: PICMG 1.0 full-size solution 4th generation LGA1150 Intel® Core™ i7/i5/i3, Pentium® or Celeron® processor supported Intel® H81 PCH Two 240-pin 1600/1333 MHz dual-channel DDR3/DDR3L DIMMs support up to...

  • Page 18: Connectors

    WSB-H810 PICMG 1.0 CPU Card 1.3 Connectors The connectors on the WSB-H810 are shown in the figure below. Figure 1-2: Connectors Page 4...

  • Page 19: Dimensions

    WSB-H810 PICMG 1.0 CPU Card 1.4 Dimensions The main dimensions of the WSB-H810 are shown in the diagram below. Figure 1-3: WSB-H810 Dimensions (mm) Page 5...

  • Page 20: Figure 1-4: External Interface Panel Dimensions (Mm)

    WSB-H810 PICMG 1.0 CPU Card Figure 1-4: External Interface Panel Dimensions (mm) Page 6...

  • Page 21: Data Flow

    WSB-H810 PICMG 1.0 CPU Card 1.5 Data Flow Figure 1-5 shows the data flow between the system chipset, the CPU and other components installed on the motherboard. Figure 1-5: Data Flow Diagram Page 7...

  • Page 22: Technical Specifications

    WSB-H810 PICMG 1.0 CPU Card 1.6 Technical Specifications The WSB-H810 technical specifications are listed below. Specification/Model WSB-H810 PICMG 1.0 Form Factor 4th generation LGA1150 Intel® Core™ i7/i5/i3, Pentium® CPU Supported or Celeron® CPU Intel® H81 Memory Two 240-pin 1600/1333 MHz dual-channel unbuffered...
  • Page 23 WSB-H810 PICMG 1.0 CPU Card Specification/Model WSB-H810 Two RJ-45 GbE ports Ethernet One 4-pin smart fan connector (CPU fan) One 3-pin smart fan connector (system fan) Front Panel One 14-pin header (power LED, HDD LED, speaker, power button, reset button)

  • Page 24: Table 1-1: Wsb-H810 Specifications

    WSB-H810 PICMG 1.0 CPU Card Specification/Model WSB-H810 Physical Specifications Dimensions 338 mm x 122 mm Weight (GW/NW) 1000 g/260 g Table 1-1: WSB-H810 Specifications Page 10...

  • Page 25: Packing List

    WSB-H810 PICMG 1.0 CPU Card Chapter Packing List Page 11...

  • Page 26: Anti-Static Precautions

    Only handle the edges of the PCB: Don't touch the surface of the motherboard. Hold the motherboard by the edges when handling. 2.2 Unpacking Precautions When the WSB-H810 is unpacked, please do the following: Follow the anti-static guidelines above. Make sure the packing box is facing upwards when opening.

  • Page 27: Packing List

    If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the WSB-H810 was purchased from or contact an IEI sales representative directly by sending an email to ales@ieiworld.com.

  • Page 28: Optional Items

    WSB-H810 PICMG 1.0 CPU Card 2.4 Optional Items The following are optional components which may be separately purchased: Item and Part Number Image Dual RS-232 cable, 230 mm, P=2.54 (P/N: 19800-000051-RS) RS-422/485 cable, 200 mm (P/N: 32205-003800-300-RS) Dual-port USB 3.0 cable with bracket (P/N: 19800-010500-200-RS) Dual-port USB cable with bracket, 300 mm, P=2.54...
  • Page 29 WSB-H810 PICMG 1.0 CPU Card Item and Part Number Image LGA1150 cooler kit, 1U chassis compatible, 65W (P/N: CF-1150SC-R10) LGA1150 cooler kit, high-performance compatible, 95W (P/N: CF-1150SE-R10) LGA1150 cooler kit, high-performance compatible, 54W (P/N: CF-1150SF-R10) DisplayPort to HDMI converter board (for IEI iDP...

  • Page 30: Table 2-2: Optional Items

    WSB-H810 PICMG 1.0 CPU Card Item and Part Number Image 7.1-channel HD audio kit with Realtek ALC892 audio codec supporting dual audio stream (P/N: AC-KIT-892HD-R10) 20-pin Infineon TPM module, software management tool, firmware v3.17 (P/N: TPM-IN01-R11) Table 2-2: Optional Items...

  • Page 31: Connectors

    WSB-H810 PICMG 1.0 CPU Card Chapter Connectors Page 17...

  • Page 32: Peripheral Interface Connectors

    WSB-H810 PICMG 1.0 CPU Card 3.1 Peripheral Interface Connectors This chapter details all the jumpers and connectors. 3.1.1 WSB-H810 Layout The figures below show all the connectors and jumpers. Figure 3-1: Connectors and Jumpers Page 18...

  • Page 33: Peripheral Interface Connectors

    WSB-H810 PICMG 1.0 CPU Card 3.1.2 Peripheral Interface Connectors The table below lists all the connectors on the board. Connector Type Label +12V power connector 4-pin Molex power CPU12V1 connector ATX power supply enable connector 3-pin wafer ATXCTL1 Audio kit connector...

  • Page 34: External Interface Panel Connectors

    WSB-H810 PICMG 1.0 CPU Card Connector Type Label Serial port, RS-232 10-pin box header COM1, COM3, COM4, COM5 Serial port, RS-422/485 4-pin wafer COM2 SMBus connector 4-pin wafer SPI flash connector 8-pin header JSPI1 SPI flash connector (EC) 8-pin header...

  • Page 35: Internal Peripheral Connectors

    CN Pinouts: See Table 3-4 The ATX power supply enable connector enables the WSB-H810 to be connected to an ATX power supply. To enable an ATX power supply, the AT and ATX power mode selection switch must also be configured. Please refer to Chapter 4 for more details.

  • Page 36: Audio Kit Connector

    WSB-H810 PICMG 1.0 CPU Card Figure 3-3: ATX Power Supply Enable Connector Location Description PS_ON# 5VSB Table 3-4: ATX Power Supply Enable Connector Pinouts 3.2.3 Audio Kit Connector CN Label: J_AUDIO1 10-pin header, p=2 mm CN Type: CN Location: See Figure 3-4...

  • Page 37: Battery Connector

    WSB-H810 PICMG 1.0 CPU Card Description Description HDA_SDOUT HDA_SPKR HDA_SDIN HDA_RST# HDA_VCC HDA_GND HDA_+12V HDA_GND Table 3-5: Audio Kit Connector Pinouts 3.2.4 Battery Connector CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery.

  • Page 38: Chassis Intrusion Connector

    WSB-H810 PICMG 1.0 CPU Card Description Battery+ Table 3-6: Battery Connector Pinouts 3.2.5 Chassis Intrusion Connector CN Label: CHASSIS1 CN Type: 2-pin header, p=2.54 mm CN Location: F igure 3-6 CN Pinouts: See Table 3-7 The chassis intrusion connector is for a chassis intrusion detection sensor or switch that detects if a chassis component is removed or replaced.

  • Page 39: Digital I/O Connector

    WSB-H810 PICMG 1.0 CPU Card Figure 3-7: DDR3 DIMM Slot Locations 3.2.7 Digital I/O Connector CN Label: DIO1 CN Type: 10-pin header, p=2 mm CN Location: See Figure 3-8 CN Pinouts: See Table 3-8 The digital I/O connector provides programmable input and output for external devices.

  • Page 40: Ec Debug Connector

    WSB-H810 PICMG 1.0 CPU Card 3.2.8 EC Debug Connector CN Label: CN Type: 18-pin header, p=2 mm CN Location: See Figure 3-9 See Table 3-9 CN Pinouts: The EC debug connector is used for EC debug. Figure 3-9: EC Debug Connector Location...

  • Page 41: Fan Connector (System)

    WSB-H810 PICMG 1.0 CPU Card CN Location: See Figure 3-10 CN Pinouts: See Table 3-10 The fan connector attaches to a CPU cooling fan. Figure 3-10: CPU Fan Connector Location Description +12 V FANIO Table 3-10: CPU Fan Connector Pinouts 3.2.10 Fan Connector (System)

  • Page 42: Front Panel Connector

    WSB-H810 PICMG 1.0 CPU Card Figure 3-11: System Fan Connector Location Description FANIO +12 V (PWM) Table 3-11: System Fan Connector Pinouts 3.2.11 Front Panel Connector CN Label: F_PANEL1 CN Type: 14-pin header, p=2.54 mm CN Location: See Figure 3-12...

  • Page 43: I 2 C Connector

    WSB-H810 PICMG 1.0 CPU Card Function Description Function Description Power LED Speaker BEEP_PWR Power Button PWRBTN_SW# PC_BEEP Reset HDD LED EXTRST- SATA_LED# Table 3-12: Front Panel Connector Pinouts 3.2.12 I C Connector CN Label: CN Type: 4-pin wafer, p=1.25 mm...

  • Page 44: Infrared Connector (Reserved)

    WSB-H810 PICMG 1.0 CPU Card 3.2.13 Infrared Connector (Reserved) CN Label: 5-pin header, p=2.54 mm CN Type: CN Location: See Figure 3-14 CN Pinouts: See Table 3-14 The infrared connector attaches to an infrared receiver for use with remote controls.

  • Page 45: Keyboard And Mouse Connector

    WSB-H810 PICMG 1.0 CPU Card Figure 3-15: Internal DisplayPort Connector Location Description Description AUX_P AUX_N AUX_ DET LANE2P LANE3P LANE2N LANE3N LANE0P LANE1P LANE0N LANE1N VCC3V VCC5V Table 3-15: Internal DisplayPort Connector Pinouts 3.2.15 Keyboard and Mouse Connector CN Label:...

  • Page 46: Lan Led Connectors

    WSB-H810 PICMG 1.0 CPU Card Figure 3-16: Keyboard and Mouse Connector Location Description +5 VCC Mouse Data Mouse Clock Keyboard Data Keyboard Clock GROUND Table 3-16: Keyboard and Mouse Connector Pinouts 3.2.16 LAN LED Connectors CN Label: LED_LAN1, LED_LAN2 2-pin header, p=2.54 mm...

  • Page 47: Msata Slot

    WSB-H810 PICMG 1.0 CPU Card Figure 3-17: LAN LED Connector Locations Description +3.3V LAN1_LED_LINK#_ACT Table 3-17: LAN1 LED Connector (LED_LAN1) Pinouts Description +3.3V LAN2_LED_LINK#_ACT Table 3-18: LAN2 LED Connector (LED_LAN2) Pinouts 3.2.17 mSATA Slot CN Label: MSATA1 CN Type: PCIe Mini...

  • Page 48: Figure 3-18: Msata Slot Location

    WSB-H810 PICMG 1.0 CPU Card Figure 3-18: mSATA Slot Location Description Description PCIE_WAKE# +3.3V 1.5V +3.3V PLTRST_N SATA_RX+_C +3.3V SATA_RX-_C 1.5V SMB_CLK SATA_TX-_C SMB_DATA SATA_TX+_C +3.3V +3.3V +3.3V Page 34...

  • Page 49: Parallel Port Connector

    WSB-H810 PICMG 1.0 CPU Card Description Description 1.5V +3.3V Table 3-19: mSATA Slot Pinouts 3.2.18 Parallel Port Connector CN Label: LPT1 26-pin box header, p=2.54 mm CN Type: CN Location: See Figure 3-19 CN Pinouts: See Table 3-20 The parallel port connector connects to a parallel port connector interface or some other parallel port device such as a printer.

  • Page 50: Pcie Mini Slot

    WSB-H810 PICMG 1.0 CPU Card Description Description PPD5 PPD6 PPD7 BUSY SLCT Table 3-20: Parallel Port Connector Pinouts 3.2.19 PCIe Mini Slot CN Label: MPCIE1 CN Type: PCIe Mini CN Location: F igure 3-20 CN Pinouts: See Table 3-21 The PCIe Mini slot is for installing a full-size or half-size PCIe Mini expansion card.

  • Page 51: Sata 3Gb/S Drive Connector

    WSB-H810 PICMG 1.0 CPU Card Description Description WLAN_EN PLTRST_N PCIE_RX- +3.3V PCIE_RX+ 1.5V SMB_CLK PCIE_TX- SMB_DATA PCIE_TX+ USB_D- USB_D+ +3.3V +3.3V +3.3V 1.5V +3.3V Table 3-21: PCIe Mini Slot Pinouts 3.2.20 SATA 3Gb/s Drive Connector CN Label: S_ATA3 CN Type:...

  • Page 52: Sata 6Gb/S Drive Connectors

    WSB-H810 PICMG 1.0 CPU Card Figure 3-21: SATA 3Gb/s Drive Connector Location Description Description Table 3-22: SATA 3Gb/s Drive Connector Pinouts 3.2.21 SATA 6Gb/s Drive Connectors CN Label: S_ATA1, S_ATA2 7-pin SATA drive connector CN Type: CN Location: See Figure 3-22...

  • Page 53: Serial Port Connectors, Rs-232

    WSB-H810 PICMG 1.0 CPU Card Figure 3-22: SATA 6Gb/s Drive Connector Locations Description Description Table 3-23: SATA 6Gb/s Drive Connector Pinouts 3.2.22 Serial Port Connectors, RS-232 CN Label: COM1, COM3, COM4, COM5 10-pin box header, p=2.54 mm CN Type: CN Location:...

  • Page 54: Serial Port Connector, Rs-422/485

    WSB-H810 PICMG 1.0 CPU Card Description Description Table 3-24: Serial Port Connector Pinouts 3.2.23 Serial Port Connector, RS-422/485 CN Label: COM2 4-pin wafer, p=2 mm CN Type: CN Location: See Figure 3-24 CN Pinouts: See Table 3-25 This connector provides RS-422 or RS-485 communications.

  • Page 55: Smbus Connector

    WSB-H810 PICMG 1.0 CPU Card RS-422 Pinouts RS-485 Pinouts Table 3-26: DB-9 RS-422/485 Pinouts 3.2.24 SMBus Connector CN Label: CN Type: 4-pin wafer, p=1.25 mm See Figure 3-25 CN Location: CN Pinouts: See Table 3-27 The SMBus (System Management Bus) connector provides low-speed system management communications.

  • Page 56: Spi Flash Connector

    WSB-H810 PICMG 1.0 CPU Card 3.2.25 SPI Flash Connector CN Label: JSPI1 8-pin header, p=2.54 mm CN Type: CN Location: See Figure 3-26 CN Pinouts: See Table 3-28 The SPI flash connector is used to flash the BIOS. Figure 3-26: SPI Flash Connector Location...

  • Page 57: Tpm Connector

    WSB-H810 PICMG 1.0 CPU Card Figure 3-27: SPI EC Flash Connector Location Description Description +3.3V SPI_CS# SPI_SO SPI_CLK SPI_SI Table 3-29: SPI EC Flash Connector Pinouts 3.2.27 TPM Connector CN Label: TPM1 20-pin header, p=2.54 mm CN Type: CN Location:...

  • Page 58: Usb 2.0 Connectors

    WSB-H810 PICMG 1.0 CPU Card Description Description LCLK LFRAME# LRERST# LAD3 LAD2 +3.3V LAD1 LAD0 SB3V SERIRQ GLKRUN# LPCPD# LDRQ# Table 3-30: TPM Connector Pinouts 3.2.28 USB 2.0 Connectors CN Label: USB2-4, USB2-5 CN Type: 8-pin header, p=2.54 mm CN Location:...

  • Page 59: Usb 2.0 Connector (Type A)

    WSB-H810 PICMG 1.0 CPU Card Description Description Table 3-31: USB 2.0 Connector Pinouts 3.2.29 USB 2.0 Connector (Type A) CN Label: USB2-3 USB Type A CN Type: CN Location: See Figure 3-30 CN Pinouts: See Table 3-32 The USB Type A connector connects to a USB 2.0/1.1 device.

  • Page 60: Figure 3-31: Usb 3.0 Connector Location

    WSB-H810 PICMG 1.0 CPU Card CN Pinouts: See Table 3-33 The USB 3.0 connector connects to USB 3.0 devices. This connector provides two USB 3.0 ports. Figure 3-31: USB 3.0 Connector Location Description Description USB_DATA+ USB3_RX- USB_DATA- USB3_RX+ USB3_TX+ USB3_TX-...

  • Page 61: External Peripheral Interface Connector Panel

    CN Type: CN Location: See Figure 3-32 CN Pinouts: See Figure 3-33 and Table 3-34 The WSB-H810 is equipped with two built-in RJ-45 Ethernet controllers. Each controller can connect to the LAN through one RJ-45 LAN connector. Description Description MDIA3-...

  • Page 62: Usb 2.0 Connectors

    CN Type: USB port CN Location: See Figure 3-32 See Table 3-36 CN Pinouts: The WSB-H810 has two external USB 2.0 ports. The ports connect to both USB 2.0 and USB 1.1 devices. Description DATA- DATA+ GROUND Table 3-36: USB 2.0 Port Pinouts 3.3.3 VGA Connector...

  • Page 63: Figure 3-34: Vga Connector

    WSB-H810 PICMG 1.0 CPU Card The VGA connector connects to a monitor that accepts a standard VGA input. Description Description GREEN BLUE DDCDA HSYNC VSYNC DDCCLK Table 3-37: VGA Connector Pinouts Figure 3-34: VGA Connector Page 49...

  • Page 64: Installation

    WSB-H810 PICMG 1.0 CPU Card Chapter Installation Page 50...

  • Page 65: Anti-Static Precautions

    Electrostatic discharge (ESD) can cause serious damage to electronic components, including the WSB-H810. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the WSB-H810 or any other electrical component is handled, the following anti-static precautions are strictly adhered to.
  • Page 66 This helps to prevent potential ESD damage. Turn all power to the WSB-H810 off: When working with the WSB-H810, make sure that it is disconnected from all power supplies and that no electricity is being fed into the system.

  • Page 67: Socket Lga1150 Cpu Installation

    WSB-H810 PICMG 1.0 CPU Card 4.3 Socket LGA1150 CPU Installation WARNING: CPUs are expensive and sensitive components. When installing the CPU please be careful not to damage it in anyway. Make sure the CPU is installed properly and ensure the correct cooling kit is properly installed.

  • Page 68: Figure 4-2: Remove Protective Cover

    WSB-H810 PICMG 1.0 CPU Card Figure 4-2: Remove Protective Cover Step 3: Inspect the CPU socket. Make sure there are no bent pins and make sure the socket contacts are free of foreign material. If any debris is found, remove it with compressed air.

  • Page 69: Figure 4-3: Insert The Socket Lga1150 Cpu

    WSB-H810 PICMG 1.0 CPU Card Figure 4-3: Insert the Socket LGA1150 CPU Step 8: Close the CPU socket. Close the load plate and pull the load lever back a little to have the load plate be able to secure to the knob. Engage the load lever by pushing it back to its original position (Figure 4-4).

  • Page 70: Socket Lga1150 Cooling Kit Installation

    WSB-H810 PICMG 1.0 CPU Card 4.4 Socket LGA1150 Cooling Kit Installation The cooling kit can be bought from IEI. The cooling kit has a heatsink and fan. WARNING: Do not wipe off (accidentally or otherwise) the pre-sprayed layer of thermal paste on the bottom of the heat sink. The thermal paste between the CPU and the heat sink is important for optimum heat dissipation.

  • Page 71: Dimm Installation

    Step 5: Connect the fan cable. Connect the cooling kit fan cable to the fan connector on the WSB-H810. Carefully route the cable and avoid heat generating chips and fan blades. 4.5 DIMM Installation To install a DIMM, please follow the steps below and refer to Figure 4-6.

  • Page 72: Full-Size Pcie Mini Card Installation

    WSB-H810 PICMG 1.0 CPU Card 4.6 Full-size PCIe Mini Card Installation The PCIe Mini slot allows installation of either a full-size or half-size PCIe Mini card. To install a full-size PCIe Mini card, please follow the steps below. Step 1: Locate the PCIe Mini slot.

  • Page 73: Figure 4-8: Removing The Retention Screw

    WSB-H810 PICMG 1.0 CPU Card Figure 4-8: Removing the Retention Screw Step 4: Insert into the socket at an angle. Line up the notch on the card with the notch on the slot. Slide the PCIe Mini card into the socket at an angle of about 20º (Figure 4-9).

  • Page 74: Half-Size Pcie Mini Card Installation

    WSB-H810 PICMG 1.0 CPU Card Step 5: Secure the full-size PCIe Mini card. Secure the full-size PCIe Mini card with the retention screw previously removed (Figure 4-10). Figure 4-10: Securing the Full-size PCIe Mini Card 4.7 Half-size PCIe Mini Card Installation The PCIe Mini card slot allows installation of either a full-size or half-size PCIe Mini card.

  • Page 75: Figure 4-11: Removing The Retention Screw

    WSB-H810 PICMG 1.0 CPU Card Figure 4-11: Removing the Retention Screw Step 3: Insert into the socket at an angle. Line up the notch on the card with the notch on the slot. Slide the PCIe Mini card into the slot at an angle of about 20º...

  • Page 76: Msata Card Installation

    WSB-H810 PICMG 1.0 CPU Card Step 4: Secure the half-size PCIe Mini card. Secure the half-size PCIe Mini card with the retention screw previously removed (Figure 4-13). Step 0: Figure 4-13: Securing the Half-size PCIe Mini Card 4.8 mSATA Card Installation The mSATA slot allows installation of a full-size mSATA card.

  • Page 77: Figure 4-14: Removing The Retention Screws

    WSB-H810 PICMG 1.0 CPU Card Figure 4-14: Removing the Retention Screws Step 3: Insert into the socket at an angle. Line up the notch on the card with the notch on the slot. Slide the mSATA card into the slot at an angle of about 20º (Figure 4-15).

  • Page 78: System Configuration

    WSB-H810 PICMG 1.0 CPU Card Step 4: Secure the mSATA card. Secure the mSATA card with the retention screws previously removed (Figure 4-16). Step 0: Figure 4-16: Securing the mSATA Card 4.9 System Configuration The system configuration should be performed before installation.

  • Page 79: Clear Cmos Button

    WSB-H810 PICMG 1.0 CPU Card Setting Description 1-2 (down) ATX power mode (default) 2-3 (up) AT power mode Table 4-1: AT/ATX Power Mode Switch Settings 4.9.2 Clear CMOS Button To reset the BIOS, remove the on-board battery and press the clear CMOS button for three seconds or more.

  • Page 80: Usb Power Selection

    WSB-H810 PICMG 1.0 CPU Card Figure 4-19: Flash Descriptor Security Override Jumper Location To update the ME firmware, please follow the steps below. Step 1: Before turning on the system power, short pin 2-3 of the Flash Descriptor Security Override jumper.

  • Page 81: Chassis Installation

    The WSB-H810 must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface. In a system with an individual power supply unit, the cooling fan of a power supply can also help generate airflow through the board surface.

  • Page 82: Internal Peripheral Device Connections

    This section outlines the installation of peripheral devices to the onboard connectors. 4.11.1 SATA Drive Connection The WSB-H810 is shipped with four SATA drive cables. To connect the SATA drives to the connectors, please follow the steps below. Step 1: Locate the connectors.

  • Page 83: Figure 4-21: Sata Power Drive Connection

    WSB-H810 PICMG 1.0 CPU Card Step 4: Connect the SATA power cable (optional). Connect the SATA power connector to the back of the SATA drive. See Figure 4-21. Figure 4-21: SATA Power Drive Connection Page 69...

  • Page 84: Bios

    WSB-H810 PICMG 1.0 CPU Card Chapter BIOS Page 70...

  • Page 85: Introduction

    WSB-H810 PICMG 1.0 CPU Card 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. NOTE: Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.

  • Page 86: Getting Help

    WSB-H810 PICMG 1.0 CPU Card Function Page Dn Move to the next page Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu...

  • Page 87: Main

    WSB-H810 PICMG 1.0 CPU Card 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.

  • Page 88: Advanced

    WSB-H810 PICMG 1.0 CPU Card System Overview The system overview lists a brief summary of the BIOS. The fields in system overview cannot be changed. The items shown in the system overview include: BIOS Information Processor Information Memory Information PCH Information...

  • Page 89: Acpi Settings

    WSB-H810 PICMG 1.0 CPU Card Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit > ACPI Settings System ACPI Parameters > RTC Wake Settings > Trusted Computing > CPU Configuration > SATA Configuration ---------------------- >...

  • Page 90: Rtc Wake Settings

    WSB-H810 PICMG 1.0 CPU Card ACPI Sleep State [S1 only (CPU Stop Clock)] Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used. S1 only (CPU Stop The system enters S1 (POS) sleep state. The...
  • Page 91 WSB-H810 PICMG 1.0 CPU Card Wake system with Fixed Time [Disabled] Use the Wake system with Fixed Time option to enable or disable the system wake on alarm event. Disabled The real time clock (RTC) cannot generate a wake EFAULT...

  • Page 92: Trusted Computing

    WSB-H810 PICMG 1.0 CPU Card 5.3.3 Trusted Computing Use the Trusted Computing menu (BIOS Menu 5) to configure settings related to the Trusted Computing Group (TCG) Trusted Platform Module (TPM). Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.

  • Page 93: Cpu Configuration

    WSB-H810 PICMG 1.0 CPU Card 5.3.4 CPU Configuration Use the CPU Configuration menu (BIOS Menu 6) to view detailed CPU specifications or enable the Intel Virtualization Technology. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced CPU Configuration...
  • Page 94 WSB-H810 PICMG 1.0 CPU Card Active Processor Cores [All] Use the Active Processor Cores BIOS option to enable numbers of cores in the processor package. Enable all cores in the processor package. EFAULT Enable one core in the processor package.

  • Page 95: Sata Configuration

    WSB-H810 PICMG 1.0 CPU Card 5.3.5 SATA Configuration Use the SATA Configuration menu (BIOS Menu 7) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
  • Page 96 WSB-H810 PICMG 1.0 CPU Card Enabled Enables the SATA test mode. EFAULT Disables the SATA test mode. Disabled Aggressive LPM Support [Enabled] Use the Aggressive LPM Support option to enable or disable the PCH to aggressively enter link power state.

  • Page 97: Usb Configuration

    WSB-H810 PICMG 1.0 CPU Card 5.3.6 USB Configuration Use the USB Configuration menu (BIOS Menu 8) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced USB Configuration Enables Legacy USB support.

  • Page 98: F81866 Super Io Configuration

    WSB-H810 PICMG 1.0 CPU Card 5.3.7 F81866 Super IO Configuration Use the F81866 Super IO Configuration menu (BIOS Menu 9) to set or change the configurations for the serial ports and parallel port. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
  • Page 99 WSB-H810 PICMG 1.0 CPU Card 5.3.7.1.1 Serial Port 1 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Disabled Disable the serial port Enable the serial port Enabled EFAULT Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
  • Page 100 WSB-H810 PICMG 1.0 CPU Card Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address. Auto The serial port IO port address and interrupt address EFAULT are automatically detected. Serial Port I/O port address is 2F8h and the interrupt IO=2F8h;...
  • Page 101 WSB-H810 PICMG 1.0 CPU Card Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address. Auto The serial port IO port address and interrupt address EFAULT are automatically detected. Serial Port I/O port address is 2D0h and the interrupt IO=2D0h;...
  • Page 102 WSB-H810 PICMG 1.0 CPU Card IO=2E8h; Serial Port I/O port address is 2E8h and the interrupt IRQ=10, 11 address is IRQ10, 11 Serial Port I/O port address is 2D0h and the interrupt IO=2D0h; address is IRQ10, 11 IRQ=10, 11 IO=2D8h;...

  • Page 103: Irda Configuration

    WSB-H810 PICMG 1.0 CPU Card IO=2E0h; Serial Port I/O port address is 2E0h and the interrupt IRQ=10, 11 address is IRQ10, 11 5.3.7.2 IrDA Configuration Use the IrDA Configuration menu (BIOS Menu 11) to configure the infrared port. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
  • Page 104 WSB-H810 PICMG 1.0 CPU Card IO=2D8h; Infrared port I/O port address is 2D8h and the IRQ=10 interrupt address is IRQ10 Infrared port I/O port address is 2C0h and the IO=2C0h; interrupt address is IRQ10, 11 IRQ=10, 11 IO=2C8h; Infrared port I/O port address is 2C8h and the...

  • Page 105: Parallel Port Configuration

    WSB-H810 PICMG 1.0 CPU Card 5.3.7.3 Parallel Port Configuration Use the Parallel Port Configuration menu (BIOS Menu 12) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced Parallel Port Configuration Enable or Disable...

  • Page 106: Iwdd H/W Monitor

    WSB-H810 PICMG 1.0 CPU Card IO=278h; Parallel Port I/O port address is 278h and the IRQ=5, 7 interrupt address is IRQ5, 7 Parallel Port I/O port address is 3BCh and the IO=3BCh; interrupt address is IRQ5, 7 IRQ=5, 7 Device Mode [STD Printer Mode] Use the Device Mode option to select the mode the parallel port operates in.

  • Page 107: Smart Fan Mode Configuration

    WSB-H810 PICMG 1.0 CPU Card PC Health Status The following system parameters and values are shown. The system parameters that are monitored are: System Temperatures: CPU Temperature System Temperature Fan Speeds: CPU Fan Speed System Fan Speed Voltages: CPU_CORE +12V +5VSB +3.3V...

  • Page 108: Serial Port Console Redirection

    WSB-H810 PICMG 1.0 CPU Card CPU_FAN1 Smart Fan Control/SYS_FAN1 Smart Fan Control [Auto Mode] Use the CPU_FAN1 Smart Fan Control/SYS_FAN1 Smart Fan Control option to configure the CPU/System Smart Fan. Auto Mode The fan adjusts its speed using Auto Mode EFAULT settings.

  • Page 109: Bios Menu 15: Serial Port Console Redirection

    WSB-H810 PICMG 1.0 CPU Card Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced COM1 Console Redirection Console Redirection [Disabled] Enable or Disable > Console Redirection Settings COM2 Console Redirection [Disabled] > Console Redirection Settings --------------------- COM3 : Select Screen ↑...
  • Page 110 WSB-H810 PICMG 1.0 CPU Card Bits per second [115200] Use the Bits per second option to specify the serial port transmission speed. The speed must match the other side. Long or noisy lines may require lower speeds. 9600 Sets the serial port transmission speed at 9600.

  • Page 111: Iei Feature

    WSB-H810 PICMG 1.0 CPU Card Stop Bits [1] Use the Stop Bits option to specify the number of stop bits used to indicate the end of a serial data packet. Communication with slow devices may require more than 1 stop bit.

  • Page 112: Chipset

    WSB-H810 PICMG 1.0 CPU Card 5.4 Chipset Use the Chipset menu (BIOS Menu 17) to access the PCH IO and System Agent (SA) configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.

  • Page 113: Pch-Io Configuration

    WSB-H810 PICMG 1.0 CPU Card 5.4.1 PCH-IO Configuration Use the PCH-IO Configuration menu (BIOS Menu 18) to configure the PCH parameters. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset Auto Power Button Status [Disable (ATX)] Select AC power state...

  • Page 114: Table 5-2: Bios Options And Configured Usb Ports

    WSB-H810 PICMG 1.0 CPU Card USB Power SW1 [+5V DUAL] Use the USB Power SW1 BIOS option to configure the USB power source for the corresponding USB connectors (Table 5-2). Sets the USB power source to +5V +5V DUAL Sets the USB power source to +5V dual...

  • Page 115: Pci Express Configuration

    WSB-H810 PICMG 1.0 CPU Card 5.4.1.1 PCI Express Configuration Use the PCI Express Configuration menu (BIOS Menu 19) to configure the PCIe Mini slot. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset PCI Express Configuration MINI-PCIE Setting >...
  • Page 116 WSB-H810 PICMG 1.0 CPU Card PCIe Speed [Auto] Use this option to select the support type of the PCIe Mini slot. The following options are available: Auto Default Gen1 Gen2 Detect Non-Compliance Device [Disabled] Use the Detect Non-Compliance Device option to enable or disable detecting if a non-compliance PCI Express device is connected to the PCI Express slot.

  • Page 117: Pch Azalia Configuration

    WSB-H810 PICMG 1.0 CPU Card 5.4.1.2 PCH Azalia Configuration Use the PCH Azalia Configuration menu (BIOS Menu 21) to configure the PCH Azalia settings. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset PCH Azalia Configuration Control Detection of the Azalia device.

  • Page 118: System Agent (Sa) Configuration

    WSB-H810 PICMG 1.0 CPU Card 5.4.2 System Agent (SA) Configuration Use the System Agent (SA) Configuration menu (BIOS Menu 22) to configure the System Agent (SA) parameters. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset VT-d [Disabled] Check to enable VT-d function on MCH.

  • Page 119: Bios Menu 23: Graphics Configuration

    WSB-H810 PICMG 1.0 CPU Card Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset Graphics Configuration Select which of IGFX/PEG/PCI Graphics Primary Display [Auto] device should be Primary DVMT Pre-Allocated [256M] Display Or select SG for DVMT Total Gfx Mem [MAX] Switchable Gfx.

  • Page 120: Lcd Control

    WSB-H810 PICMG 1.0 CPU Card DVMT Total Gfx Mem [MAX] Use the DVMT Total Gfx Mem option to select DVMT5.0 total graphic memory size used by the internal graphic device. The following options are available: 128M 256M Default 5.4.2.1.1 LCD Control Aptio Setup Utility –...

  • Page 121: Nb Pcie Configuration

    WSB-H810 PICMG 1.0 CPU Card 5.4.2.2 NB PCIe Configuration Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset NB PCIe Configuration Configure PEG0 B0:D1:F0 PEG0 Not Present Gen1-Gen2 PEG0 – Gen X [Auto] Enable PEG [Auto] ---------------------- Detect Non-compliance Device...

  • Page 122: Memory Configuration

    WSB-H810 PICMG 1.0 CPU Card Disabled Disables to detect if a non-compliance PCI EFAULT Express device is connected to the PCI Express port. Enables to detect if a non-compliance PCI Express Enabled device is connected to the PCI Express port.

  • Page 123: Boot

    WSB-H810 PICMG 1.0 CPU Card 5.5 Boot Use the Boot menu (BIOS Menu 27) to configure system boot options. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Boot Configuration Select the keyboard...
  • Page 124 WSB-H810 PICMG 1.0 CPU Card Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots. Normal POST messages displayed Disabled Enabled OEM Logo displayed instead of POST messages EFAULT Option ROM Messages [Force BIOS] Use the Option ROM Messages option to set the Option ROM display mode.

  • Page 125: Security

    WSB-H810 PICMG 1.0 CPU Card 5.6 Security Use the Security menu (BIOS Menu 28) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Password Description...

  • Page 126: Bios Menu 29: Save & Exit

    WSB-H810 PICMG 1.0 CPU Card Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Reset Exit the system after Discard Changes and Reset saving the changes. Restore Defaults...

  • Page 127: Software Drivers

    WSB-H810 PICMG 1.0 CPU Card Chapter Software Drivers Page 113...

  • Page 128: Available Software Drivers

    USB 3.0 Installation instructions are given below. 6.2 Software Installation All the drivers for the WSB-H810 are on the CD that came with the system. To install the drivers, please follow the steps below. Step 1: Insert the CD into a CD drive connected to the system.

  • Page 129: Chipset Driver Installation

    WSB-H810 PICMG 1.0 CPU Card 6.3 Chipset Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “1-Chipset”. Step 3: Locate the setup file and double click on it.

  • Page 130: Figure 6-2: Chipset Driver License Agreement

    WSB-H810 PICMG 1.0 CPU Card Figure 6-2: Chipset Driver License Agreement Step 9: The Read Me file in Figure 6-3 appears. Step 10: Click Next to continue. Figure 6-3: Chipset Driver Read Me File Page 116...

  • Page 131: Figure 6-4: Chipset Driver Setup Progress

    WSB-H810 PICMG 1.0 CPU Card Step 11: Setup Progress is performed as shown in Figure 6-4. Step 12: Once the Setup Progress is complete, click Next to continue. Figure 6-4: Chipset Driver Setup Progress Step 13: The Setup Is Complete screen in Figure 6-5 appears. Click Finish to exit.

  • Page 132: Graphics Driver Installation

    WSB-H810 PICMG 1.0 CPU Card 6.4 Graphics Driver Installation To install the Graphics driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “2-Graphic”. Step 3: Double click the setup file which corresponds to the operating system.

  • Page 133: Figure 6-7: Graphics Driver - Extracting Files

    WSB-H810 PICMG 1.0 CPU Card Figure 6-7: Graphics Driver – Extracting Files Step 7: The Welcome Screen in Figure 6-8 appears. Click Next to continue. Figure 6-8: Graphics Driver Welcome Screen Page 119...

  • Page 134: Figure 6-9: Graphics Driver License Agreement

    WSB-H810 PICMG 1.0 CPU Card Step 8: The License Agreement in Figure 6-9 appears. Click Yes to accept the agreement and continue. Figure 6-9: Graphics Driver License Agreement Step 9: The Read Me file in Figure 6-10 appears. Click Next to continue.

  • Page 135: Figure 6-11: Graphics Driver Setup Progress

    WSB-H810 PICMG 1.0 CPU Card Step 10: Setup Operations are performed as shown in Figure 6-11. Step 11: Once the Setup Operations are complete, click Next to continue. Figure 6-11: Graphics Driver Setup Progress Step 12: The Finish screen in Figure 6-12 appears. Select “Yes, I want to restart this computer now”...

  • Page 136: Lan Driver Installation

    WSB-H810 PICMG 1.0 CPU Card 6.5 LAN Driver Installation To install the LAN driver, please do the following. Step 1: Right-click the Computer button from the start menu and select Properties (Figure 6-13). Figure 6-13: Windows Control Panel Step 2: The system control panel window in Figure 6-14 appears.

  • Page 137: Figure 6-15: Device Manager List

    WSB-H810 PICMG 1.0 CPU Card Step 4: A list of system hardware devices appears (Figure 6-15). Step 5: Right-click one of the Ethernet controllers that has question marks next to it (this means Windows does not recognize the device). Step 6: Select Update Driver Software.

  • Page 138: Figure 6-16: Update Driver Software Window

    WSB-H810 PICMG 1.0 CPU Card Step 7: The Update Driver Software Window appears (Figure 6-16). Figure 6-16: Update Driver Software Window Step 8: Select “Browse my computer for driver software”. Step 9: Click Browse to select “X:\3-LAN” directory in the Locate File window, where “X:\”...

  • Page 139: Audio Driver Installation

    WSB-H810 PICMG 1.0 CPU Card Step 11: Driver Installation is performed as shown in Figure 6-18. Figure 6-18: LAN Driver Installation Step 12: The Finish screen appears. Click Close to exit. Step 13: Right-click the other Ethernet controller that has question marks next to it as shown in Figure 6-15.

  • Page 140: Figure 6-19: Audio Driver - Extracting Files

    WSB-H810 PICMG 1.0 CPU Card Figure 6-19: Audio Driver – Extracting Files Step 5: The Audio Driver Installation screen in Figure 6-20 appears. Click Yes to install the audio driver. Figure 6-20: Audio Driver Installation Welcome Screen Step 6: The driver installation begins.

  • Page 141: Usb 3.0 Driver Installation

    WSB-H810 PICMG 1.0 CPU Card Figure 6-21: Audio Driver Installation Complete Step 8: The system reboots. 6.7 USB 3.0 Driver Installation WARNING: Do not run this driver’s installer (Setup.exe) from a USB storage device (ie. external USB hard drive or USB thumb drive). For proper installation, please copy driver files to a local hard drive folder and run from there.

  • Page 142: Figure 6-22: Usb 3.0 Driver Welcome Screen

    WSB-H810 PICMG 1.0 CPU Card Figure 6-22: USB 3.0 Driver Welcome Screen Step 5: The license agreement in Figure 6-23 appears. Read the License Agreement. Step 6: Click Yes to continue. Figure 6-23: USB 3.0 Driver License Agreement Page 128...

  • Page 143: Figure 6-24: Usb 3.0 Driver Read Me File

    WSB-H810 PICMG 1.0 CPU Card Step 7: The Read Me file in Figure 6-24 appears. Click Next to continue. Figure 6-24: USB 3.0 Driver Read Me File Step 8: Setup Operations are performed as shown in Figure 6-25. Step 9: Once the Setup Operations are complete, click Next to continue.

  • Page 144: Figure 6-26: Usb 3.0 Driver Installation Finish Screen

    WSB-H810 PICMG 1.0 CPU Card Step 10: The Finish screen in Figure 6-26 appears. Step 11: Select “Yes, I want to restart this computer now” and click Finish.Step 0: Figure 6-26: USB 3.0 Driver Installation Finish Screen Page 130...

  • Page 145: A Regulatory Compliance

    WSB-H810 PICMG 1.0 CPU Card Appendix Regulatory Compliance Page 131...
  • Page 146 WSB-H810 PICMG 1.0 CPU Card DECLARATION OF CONFORMITY This equipment has been tested and found to comply with specifications for CE marking. If the user modifies and/or installs other devices in the equipment, the CE conformity declaration may no longer apply.

  • Page 147: B Product Disposal

    WSB-H810 PICMG 1.0 CPU Card Appendix Product Disposal Page 133...
  • Page 148 WSB-H810 PICMG 1.0 CPU Card CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. Outside the European Union–If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.

  • Page 149: Cbios Options

    WSB-H810 PICMG 1.0 CPU Card Appendix BIOS Options Page 135...
  • Page 150 WSB-H810 PICMG 1.0 CPU Card Below is a list of BIOS configuration options in the BIOS chapter. 　 System Overview .........................74 　 System Date [xx/xx/xx] ......................74 　 System Time [xx:xx:xx] .......................74 　 ACPI Sleep State [S1 only (CPU Stop Clock)]..............76 　...
  • Page 151 WSB-H810 PICMG 1.0 CPU Card 　 Device Mode [STD Printer Mode] ..................92 　 PC Health Status ........................93 　 CPU_FAN1 Smart Fan Control/SYS_FAN1 Smart Fan Control [Auto Mode] ....94 　 Fan start/off temperature ....................94 　 Fan start PWM ........................94 　 Fan slope PWM ........................94 　...
  • Page 152 WSB-H810 PICMG 1.0 CPU Card 　 Save Changes and Reset ....................112 　 Discard Changes and Reset .................... 112 　 Restore Defaults ....................... 112 　 Save as User Defaults ...................... 112 　 Restore User Defaults ...................... 112 Page 138...

  • Page 153: D Terminology

    WSB-H810 PICMG 1.0 CPU Card Appendix Terminology Page 139...
  • Page 154 WSB-H810 PICMG 1.0 CPU Card AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface.
  • Page 155 WSB-H810 PICMG 1.0 CPU Card DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module. The digital inputs and digital outputs are general control signals that control the on/off circuit of external devices or TTL devices.
  • Page 156 WSB-H810 PICMG 1.0 CPU Card LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer. POST The Power-on Self Test (POST) is the pre-boot actions the system performs when the system is turned-on.

  • Page 157: E Digital I/O Interface

    WSB-H810 PICMG 1.0 CPU Card Appendix Digital I/O Interface Page 143...

  • Page 158: Introduction

    WSB-H810 PICMG 1.0 CPU Card E.1 Introduction The DIO connector on the WSB-H810 is interfaced to GPIO ports on the Super I/O chipset. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices. Data can be read or written to the selected address to enable the DIO functions.

  • Page 159: Assembly Language Sample 1

    WSB-H810 PICMG 1.0 CPU Card E.2 Assembly Language Sample 1 AX, 6F08H ;setting the digital port as input AL low byte = value AH – 6FH Sub-function: AL – 9 :Set the digital port as OUTPUT :Digital I/O input value E.3 Assembly Language Sample 2...

  • Page 160: F Watchdog Timer

    WSB-H810 PICMG 1.0 CPU Card Appendix Watchdog Timer Page 146...
  • Page 161 WSB-H810 PICMG 1.0 CPU Card NOTE: The following discussion applies to DOS environment. Contact IEI support or visit the IEI website for specific drivers for other operating systems. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash.
  • Page 162 WSB-H810 PICMG 1.0 CPU Card NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. EXAMPLE PROGRAM: ; INITIAL TIMER PERIOD COUNTER W_LOOP: AX, 6F02H ;setting the time-out value BL, 30 ;time-out value is 48 seconds ;...

  • Page 163: G Hazardous Materials Disclosure

    WSB-H810 PICMG 1.0 CPU Card Appendix Hazardous Materials Disclosure Page 149...
  • Page 164 WSB-H810 PICMG 1.0 CPU Card The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
  • Page 165 WSB-H810 PICMG 1.0 CPU Card 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元 件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯 醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 显示 印刷电路板 金属螺帽 电缆组装 风扇组装 电力供应组装 电池 O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T 11363-2006 (现由 GB/T 26572-2011 取代) 标准规定的限量要求以下。...

Table of Contents