1. Manuals
  2. Brands
  3. IEI Technology Manuals
  4. Motherboard
  5. Wafer-CX700m
  6. User manual

IEI Technology Wafer-CX700m User Manual

3.5" sbc with via c7 or via eden embedded cpu, vga, dvi, lvds, sata, audio, dual gigabit ethernet, mini pci expansion slot and compactflash slot
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
WAFER-CX700M 3.5" SBC
Page i

Advertisement

Table of Contents
loading

Related Manuals for IEI Technology Wafer-CX700m

Summary of Contents for IEI Technology Wafer-CX700m

  • Page 1 WAFER-CX700M 3.5" SBC Page i...
  • Page 2 WAFER-CX700M 3.5" SBC Revision Date Version Changes February, 2008 1.00 Initial release Page ii...
  • Page 3 WAFER-CX700M 3.5" SBC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

  • Page 4: This Page Is Intentionally Left Blank

    WAFER-CX700M 3.5" SBC THIS PAGE IS INTENTIONALLY LEFT BLANK Page iv...
  • Page 5 Cautionary messages should also be heeded to help reduce the chance of losing data or damaging the WAFER-CX700M. Cautions are easy to recognize. The word “caution” is written as “CAUTION,” both capitalized and bold and is followed. The text is the cautionary message.
  • Page 6 “NOTE,” both capitalized and bold and is followed by text. The text is the cautionary message. A note message is shown below: NOTE: This is an example of a note message. Notes should always be read. Notes contain critical information about the WAFER-CX700M. Please take note messages seriously. Page vi...

  • Page 7: Packing List

    WAFER-CX700M from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. The items listed below should all be included in the WAFER-CX700M package. 1 x WAFER-CX700M single board computer 1 x Mini jumper pack...
  • Page 8 WAFER-CX700M 3.5" SBC THIS PAGE IS INTENTIONALLY LEFT BLANK Page viii...

  • Page 9: Table Of Contents

    WAFER-CX700M 3.5" SBC Table of Contents INTRODUCTION..................... 1 1.1 I ......................2 NTRODUCTION 1.2 B ........................2 ENEFITS 1.3 F ........................3 EATURES 1.4 O ......................... 4 VERVIEW 1.5 P ..............5 ERIPHERAL ONNECTORS AND UMPERS 1.6 T ..................6...
  • Page 10 WAFER-CX700M 3.5" SBC 2.4.8.2 Lattice Semiconductor LC4032V Digital I/O Chipset......22 2.4.8.3 Fintek F81216DG LPC Serial Port Chipset..........22 2.4.9 Audio ........................ 23 ® 2.4.9.1 VIA VT1708A Audio Chipset..............24 2.5 E ............25 NVIRONMENTAL AND OWER PECIFICATIONS 2.5.1 System Monitoring ................... 25 2.5.2 Operating Temperature and Temperature Control...........
  • Page 11 WAFER-CX700M 3.5" SBC 4.2.16 SATA Drive Connectors ................. 53 4.2.17 Serial Port Connectors .................. 54 4.2.18 USB Connectors..................... 55 4.3 E ......... 56 XTERNAL ERIPHERAL NTERFACE ONNECTOR ANEL 4.3.1 LAN Connectors....................57 4.3.2 Keyboard/Mouse Connector ................58 4.3.3 Serial Port Connectors ..................59 4.3.4 VGA Connector ....................
  • Page 12 WAFER-CX700M 3.5" SBC 5.7.4 VGA Monitor Connection ................83 BIOS SETUP ......................85 6.1 I ......................86 NTRODUCTION 6.1.1 Starting Setup....................86 6.1.2 Using Setup ...................... 86 6.1.3 Getting Help..................... 87 6.1.4 Unable to Reboot After Configuration Changes..........87 6.1.5 BIOS Menu Bar....................87 6.2 M...
  • Page 13 WAFER-CX700M 3.5" SBC 7.4 N ............141 ETWORK DAPTER RIVER NSTALLATION 7.5 A ................150 UDIO RIVER NSTALLATION BIOS OPTIONS ....................157 TERMINOLOGY ....................161 DIGITAL I/O INTERFACE................. 165 C.1 I ...................... 166 NTRODUCTION C.2 DIO C ................... 166 ONNECTOR INOUTS C.3 A...
  • Page 14 WAFER-CX700M 3.5" SBC THIS PAGE IS INTENTIONALLY LEFT BLANK Page xiv...
  • Page 15 List of Figures Figure 1-1: WAFER-CX700M......................2 Figure 1-2: WAFER-CX700M Overview (Front) ................4 Figure 1-3: WAFER-CX700M Overview (Solder Side) ..............5 Figure 2-1: WAFER-CX700M Dimensions (mm) ................10 Figure 2-2: External Interface Panel Dimensions (mm) ............11 Figure 2-3: Data Flow Block Diagram ..................12 Figure 2-4: VIA®...
  • Page 16 Figure 4-18: SATA Drive Connector Locations .................54 Figure 4-19: COM Connector Pinout Locations ................55 Figure 4-20: USB Connector Pinout Locations .................56 Figure 4-21: WAFER-CX700M External Peripheral Interface Connector.........57 Figure 4-22: RJ-45 Ethernet Connector..................57 Figure 4-23: PS/2 Pinout and Configuration ................58 Figure 4-24: COM1 Pinout Locations..................59...
  • Page 17 WAFER-CX700M 3.5" SBC Figure 7-6: Setup File ........................ 134 Figure 7-7: VIA Hyperion Welcome Screen................134 Figure 7-8: License Agreement ....................135 Figure 7-9: Select Drivers ......................135 Figure 7-10: Start Driver Installation..................136 Figure 7-11: Installation Complete................... 136 Figure 7-12: Finish Installation....................137 Figure 7-13: Chipset and Graphics ..................
  • Page 18 WAFER-CX700M 3.5" SBC Figure 7-41: Operating System Folder ..................151 Figure 7-42: Operating System Version .................. 152 Figure 7-43: Select 32-bit or 64-bit................... 152 Figure 7-44: Audio Driver Folder....................153 Figure 7-45: Audio Driver Setup File ..................153 Figure 7-46: Audio Driver Setup Welcome Screen..............154 Figure 7-47: Audio Driver Selection..................
  • Page 19 WAFER-CX700M 3.5" SBC List of Tables Table 1-1: Technical Specifications....................8 Table 2-1: Supported HDD Specifications..................18 Table 2-2: Power Consumption....................26 Table 3-1: Packing List Items ......................30 Table 4-1: Peripheral Interface Connectors ................34 Table 4-2: Rear Panel Connectors ....................34 Table 4-3: Audio Connector Pinouts (10-pin) ................35 Table 4-4: Panel Backlight Connector Pinouts................36...
  • Page 20 Table 5-2: AT/ATX Power Supply Selector Settings ..............70 Table 5-3: Clear CMOS Jumper Settings..................72 Table 5-4: LVDS Voltage Selection Jumper Settings..............73 Table 5-5: RS-232/422/485 Selection Jumper Settings .............74 Table 5-6: IEI Provided Cables ....................74 Table 6-1: BIOS Navigation Keys ....................87 Page xx...
  • Page 21 WAFER-CX700M 3.5" SBC BIOS Menus BIOS Menu 1: Main ........................88 BIOS Menu 2: Advanced ......................90 BIOS Menu 3: CPU Configuration ....................91 BIOS Menu 4: IDE Configuration....................92 BIOS Menu 5: IDE Master and IDE Slave Configuration ............94 BIOS Menu 6: Super IO Configuration..................98 BIOS Menu 7: ACPI Configuration [Advanced Power Configuration]........
  • Page 22 WAFER-CX700M 3.5" SBC THIS PAGE IS INTENTIONALLY LEFT BLANK Page xxii...

  • Page 23: Introduction

    WAFER-CX700M 3.5" SBC Chapter Introduction Page 1...

  • Page 24: Introduction

    1.1 Introduction Figure 1-1: WAFER-CX700M The WAFER-CX700M 3.5” motherboard is a VIA® Eden or VIA® C7 processor platform. The WAFER-CX700M features a VIA® CX700M system chipset, which combines both Southbridge and Northbridge into a single package fitting the size of a standard Northbridge.

  • Page 25: Features

    WAFER-CX700M 3.5" SBC 1.3 Features Some of the features of the WAFER-CX700M are listed below. 3.5” form factor VIA® Eden or VIA® C7 CPU VIA® CX700M system chipset Multiple display options including 24-bit dual-channel LVDS Multiple serial port connectors including:...

  • Page 26: Overview

    WAFER-CX700M 3.5" SBC 1.4 Overview The WAFER-CX700M has a wide variety of peripheral interface connectors. Below is a labeled photo of the peripheral interface connectors on the front side of the WAFER-CX700M. Figure 1-2: WAFER-CX700M Overview (Front) Below is a photo of the peripheral interface connectors on the solder side of the WAFER-CX700M.

  • Page 27: Peripheral Connectors And Jumpers

    WAFER-CX700M 3.5" SBC Figure 1-3: WAFER-CX700M Overview (Solder Side) 1.5 Peripheral Connectors and Jumpers The WAFER-CX700M has the following connectors on-board: 1 x Audio connector 1 x Backlight inverter connector 1 x Battery connector 1 x CD audio input connector 1 x CompactFlash®...

  • Page 28: Technical Specifications

    1 x RS-232/422/485 serial port connector 2 x SATA connector 2 x USB 2.0 connector The WAFER-CX700M has the following external peripheral interface connectors on the board rear panel. 2 x RJ-45 Ethernet connectors 1 x RS-232 serial port connector...
  • Page 29 WAFER-CX700M 3.5" SBC Specification WAFER-CX700M Memory One 200-pin 1.0 GB (max.) 400/533 MHz DDR2 SO-DIMM VGA through DB-15 connector Display DVI through pin-header 24-bit dual-channel LVDS through 20-pin crimp connector BIOS AMI BIOS Audio VIA® VT1708A Dual Realtek RTL8110SC Gigabit Ethernet controllers...

  • Page 30: Table 1-1: Technical Specifications

    WAFER-CX700M 3.5" SBC Specification WAFER-CX700M Weight (GW/NW) 600 g / 160 g Table 1-1: Technical Specifications Page 8...

  • Page 31: Detailed Specifications

    WAFER-CX700M 3.5" SBC Chapter Detailed Specifications Page 9...

  • Page 32: Dimensions

    WAFER-CX700M 3.5" SBC 2.1 Dimensions 2.1.1 Board Dimensions The dimensions of the WAFER-CX700M are listed below. Length: 102 mm Width: 146 mm Figure 2-1: WAFER-CX700M Dimensions (mm) Page 10...

  • Page 33: External Interface Panel Dimensions

    WAFER-CX700M 3.5" SBC 2.1.2 External Interface Panel Dimensions External interface panel connector dimensions are show below. Figure 2-2: External Interface Panel Dimensions (mm) Page 11...

  • Page 34: Data Flow

    WAFER-CX700M 3.5" SBC 2.2 Data Flow The diagram below shows the data flow between the onboard CPU, system chipset and other components installed on the motherboard and described in the following sections of this chapter. Figure 2-3: Data Flow Block Diagram...

  • Page 35: Via ® C7 Cpu

    WAFER-CX700M 3.5" SBC ® 2.3 VIA C7 CPU The WAFER-CX700M has a VIA® C7 processor preinstalled. Figure 2-4: VIA® C7 Processor Some of the main specifications of the VIA® C7 CPU are listed below. Full x86/x87 operating system and software application compatibility Processor frequencies up to 2.0 GHz...

  • Page 36: Graphics

    WAFER-CX700M 3.5" SBC 2.4.1 Graphics Figure 2-5: Graphics The following video outputs are implemented on the WAFER-CX700M. VGA..................14 DVI ...................15 LVDS ..................15 2.4.1.1 VGA The VIA® CX700M chipset supports RGB video output through a DB-15 connector on the external peripheral connector interface. The VGA port supports RGB output and HDTV output.

  • Page 37: Dvi

    WAFER-CX700M 3.5" SBC 2.4.1.2 DVI The VIA® CX700M chipset supports DVI video output via pin header on the WAFER-CX700M. The DVI and LVDS video outputs share a video channel so only one can be used at a time. 2.4.1.3 LVDS The VIA®...

  • Page 38: Sata

    WAFER-CX700M 3.5" SBC 2.4.3 SATA The SATA controller supports two full duplex 3.0 Gbps dual channel SATA drives. The two SATA drive connectors are shown below. Figure 2-7: 1.5Gbps SATA Drive Connectors 2.4.4 IDE Controller Up to two IDE devices are supported on the IDE bus. A single IDE hard drive and CompactFlash®...

  • Page 39: Ide Slot

    WAFER-CX700M 3.5" SBC Figure 2-8: CompactFlash® Slot 2.4.4.2 IDE Slot The single IDE connector supports two ATA-6 HDDs. An ATA-6 (Ultra ATA/100) compliant IDE controller has a maximum transfer rate of 100MB/s. ATA-6 includes advancements in error checking and ATA-6 drives are compatible with future interface additions.

  • Page 40: Usb

    Controller Interface Table 2-1: Supported HDD Specifications 2.4.5 USB Four USB pin headers on the WAFER-CX700M board are interfaced to the system chipset USB controller. Four USB 1.1 or USB 2.0 devices can be connected simultaneously to the WAFER-CX700M. Figure 2-10: USB Ports...

  • Page 41: Pci Bus

    WAFER-CX700M 3.5" SBC USB 1.1 and USB 2.0 compliant 3 host ports 1 host/device 2.4.6 PCI Bus The PCI bus is connected to the components listed below: Realtek RTL8110SC GbE Controller ........19 The PCI bus complies with PCI Local Bus Specification, Revision 2.2 and supports 33MHz PCI operations.

  • Page 42: Keyboard/Mouse

    WAFER-CX700M 3.5" SBC PCI bus controller, and embedded memory. With state-of-the-art DSP technology and mixed-mode signal technology, they offer high-speed transmission over CAT 5 UTP cable or CAT 3 UTP (10Mbps only) cable. Functions such as Crossover Detection & Auto-Correction, polarity correction, adaptive equalization, cross-talk cancellation, echo cancellation, timing recovery, and error correction are implemented to provide robust transmission and reception capability at high speeds.

  • Page 43: Lpc Bus

    WAFER-CX700M 3.5" SBC Supports mouse double-click and/or mouse move power on events 2.4.8 LPC Bus The LPC bus is connected to components listed below: BIOS Chipset ................21 Lattice Semiconductor LC4032V Digital I/O Chipset ....22 Fintek F81216DG Serial Port Chipset........22 2.4.8.1 BIOS Chipset The BIOS chipset has a licensed copy of AMI BIOS installed on the chipset.

  • Page 44: Lattice Semiconductor Lc4032V Digital I/O Chipset

    WAFER-CX700M 3.5" SBC 2.4.8.2 Lattice Semiconductor LC4032V Digital I/O Chipset The Lattice Semiconductor digital I/O chipset enables a 24-bit Digital I/O. The LC4032V chipset consists of multiple 36-input, 16 macrocell Generic Logic Blocks interconnected by a Global Routing Pool. Output Routing Pools (ORPs) connect the GLBs to the I/O Blocks that contain multiple I/O cells.

  • Page 45: Audio

    WAFER-CX700M 3.5" SBC Figure 2-14: Fintek F81216DG LPC Serial Port Chipset Some of the features of the Fintek chipset are listed below: Supports LPC interface Totally provides 4 UART (16550 asynchronous) ports 3 x Pure UART 1 x UART+IR One Watch dog timer with WDTOUT# signal...

  • Page 46: Via ® Vt1708A Audio Chipset

    WAFER-CX700M 3.5" SBC ® 2.4.9.1 VIA VT1708A Audio Chipset The VIA® VT1708A High Definition Audio chipset supports 8-channel, 24-bit, 192 KHz audio content. The audio chipset features a 100dB S/N ratio and complies with the Intel® High Definition Audio Rev. 1.0 specification. VIA® HD Audio codecs include a high quality headphone amplifier, enhanced recording support, and advanced power management features, ideal for mobile devices.

  • Page 47: Environmental And Power Specifications

    The values for the above environmental parameters are all recorded in the BIOS Hardware Health Configuration menu. 2.5.2 Operating Temperature and Temperature Control The maximum and minimum operating temperatures for the WAFER-CX700M are listed below. Minimum Operating Temperature: 0ºC (32°F) Maximum Operating Temperature: 60°C (140°F)

  • Page 48: Power Consumption

    The stock heat sink and fan cover both the system chipset and CPU. 2.5.3 Power Consumption The table below shows the power consumption parameters for the WAFER-CX700M running with a 1.5 GHz VIA® C7 and 1.0 GB of 533 MHz DDR2 memory. Voltage Current 4.1 A...

  • Page 49: Unpacking

    WAFER-CX700M 3.5" SBC Chapter Unpacking Page 27...

  • Page 50: Anti-Static Precautions

    WAFER-CX700M and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the WAFER-CX700M. Dry climates are particularly susceptible to ESD. It is therefore critical that whenever the WAFER-CX700M or any other electronic component is...

  • Page 51: Package Contents

    NOTE: If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor that the WAFER-CX700M was purchased from, or contact and IEI sales representative directly by sending an email to sales@iei.com.tw.

  • Page 52: Table 3-1: Packing List Items

    WAFER-CX700M 3.5" SBC Quantity Item and Part Number Image Utility CD Quick Installation Guide Mini jumper pack (2.0mm) (P/N: 33100-000033-RS) Table 3-1: Packing List Items Page 30...

  • Page 53: Connector Pinouts

    WAFER-CX700M 3.5" SBC Chapter Connector Pinouts Page 31...

  • Page 54: Peripheral Interface Connectors

    WAFER-CX700M 3.5" SBC 4.1 Peripheral Interface Connectors Section 4.1.1 shows peripheral interface connector locations. Section 0 lists all the peripheral interface connectors seen in Section 4.1.1. 4.1.1 Layout The figures below show the on-board peripheral connectors, rear panel peripheral connectors and on-board jumpers.

  • Page 55: Peripheral Interface Connectors

    WAFER-CX700M 3.5" SBC Figure 4-2: Connector and Jumper Locations (Solder Side) 4.1.2 Peripheral Interface Connectors Table 4-1 shows a list of the peripheral interface connectors on the WAFER-CX700M. Connector Type Label Audio connector 10-pin header Backlight inverter connector 6-pin wafer...

  • Page 56: External Interface Panel Connectors

    USB connectors 8-pin header USB1 USB connectors 8-pin header USB2 Table 4-1: Peripheral Interface Connectors 4.1.3 External Interface Panel Connectors Table 4-2 lists the rear panel connectors on the WAFER-CX700M. Connector Type Label Ethernet connector RJ-45 LAN1 Ethernet connector RJ-45...

  • Page 57: Internal Peripheral Connectors

    4.2 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis. This section has complete descriptions of all the internal peripheral connectors on the WAFER-CX700M. 4.2.1 Audio Connector CN Label:...

  • Page 58: Backlight Inverter Connector

    CN Location: See Figure 4-4 CN Pinouts: See Table 4-4 The backlight inverter connector provides the backlight on the LCD display connected to the WAFER-CX700M with +12V of power. Figure 4-4: Panel Backlight Connector Pinout Locations PIN NO. DESCRIPTION 12 V...

  • Page 59: Battery Connector

    WAFER-CX700M 3.5" SBC 4.2.3 Battery Connector CN Label: 2-pin box header (1x2) CN Type: CN Location: See Figure 4-5 CN Pinouts: See Table 4-5 The battery connector is connected to a backup battery. The battery connector is also used to reset the CMOS memory if the incorrect BIOS settings have been made and the system cannot boot up.

  • Page 60: Figure 4-6: Cf Card Socket Location

    WAFER-CX700M 3.5" SBC A CF Type I or Type II memory card is inserted to the CF socket on the solder side of the WAFER-CX700M. Figure 4-6: CF Card Socket Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION GROUND CD1# DATA 3...

  • Page 61: Cd Audio Connector

    WAFER-CX700M 3.5" SBC PIN NO. DESCRIPTION PIN NO. DESCRIPTION VS2# RESET# WAIT# INPACK# REG# BVD2 DATA 0 BVD1 DATA 1 DATA 8 DATA 2 DATA 9 IOCS16# DATA 10 CD2# GROUND Table 4-6: CF Card Socket Pinouts 4.2.5 CD Audio Connector...

  • Page 62: Digital Input/Output Connector

    WAFER-CX700M 3.5" SBC PIN NO. DESCRIPTION CD Signal (Right) Ground Ground CD Signal (Left) Table 4-7: Audio CD In Connector Pinouts 4.2.6 Digital Input/Output Connector CN Label: CN Type: 10-pin header (2x5) CN Location: See Figure 4-8 CN Pinouts: See Table 4-8 The digital input/output connector is managed through a Super I/O chip.

  • Page 63: Dvi Connector

    WAFER-CX700M 3.5" SBC PIN NO. DESCRIPTION PIN NO. DESCRIPTION Input 3 Input 2 Input 1 Input 0 Table 4-8: DIO Connector Pinouts 4.2.7 DVI Connector CN Label: DVI1 26-pin header (2 x 13) CN Type: CN Location: See Figure 4-9...

  • Page 64: Fan Connector

    WAFER-CX700M 3.5" SBC PIN NO. DESCRIPTION PIN NO. DESCRIPTION -DATA1 DATA1 CLOCK -CLOCK -DATA3 DATA3 Table 4-9: DVI Connector Pinouts 4.2.8 Fan Connector CN Label: FAN1 CN Type: 3-pin wafer (1 x 3) CN Location: See Figure 4-10 CN Pinouts: See Table 4-10 The cooling fan connector provides a 12V, 500mA current to a system cooling fan.

  • Page 65: Front Panel Connector

    WAFER-CX700M 3.5" SBC PIN NO. DESCRIPTION Rotation Signal +12V Table 4-10: +12V Fan Connector Pinouts 4.2.9 Front Panel Connector CN Label: CN Type: 8-pin header (2 x 4) CN Location: See Figure 4-11 See Table 4-11 CN Pinouts: The front panel connector connects to external switches and indicators to monitor and controls the motherboard.

  • Page 66: Ide Connector

    Table 4-11: Front Panel Connector Pinouts 4.2.10 IDE Connector CN Label: 44-pin header (2 x 22) CN Type: CN Location: See Figure 4-12 CN Pinouts: See Table 4-12 One 40-pin IDE device connector on the WAFER-CX700M supports connectivity to two hard disk drives. Page 44...

  • Page 67: Figure 4-12: Ide Device Connector Locations

    WAFER-CX700M 3.5" SBC Figure 4-12: IDE Device Connector Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION RESET# GROUND DATA 7 DATA 8 DATA 6 DATA 9 DATA 5 DATA 10 DATA 4 DATA 11 DATA 3 DATA 12 DATA 2 DATA 13...

  • Page 68: Lvds Connector

    WAFER-CX700M 3.5" SBC PIN NO. DESCRIPTION PIN NO. DESCRIPTION HDC CS0# HDC CS1# HDD ACTIVE# GROUND GROUND Table 4-12: IDE Connector Pinouts 4.2.11 LVDS Connector CN Label: LVDS1 CN Type: 30-pin crimp (2 x 15) CN Location: See Figure 4-13...

  • Page 69: Mini Pci Slot

    WAFER-CX700M 3.5" SBC PIN NO. DESCRIPTION PIN NO. DESCRIPTION GROUND GROUND LVDSA_DATA0 LVDSA_DATA#0 LVDSA_DATA1 LVDSA_ DATA#1 LVDSA_DATA2 LVDSA_ DATA#2 LVDSA_CLK LVDSA_CLK# LVDSA_DATA3 LVDSA_DATA#3 GROUND GROUND LVDSB_DATA0 LVDSB_DATA0# LVDSB_DATA1 LVDSB_DATA1# LVDSB_DATA2 LVDSB_DATA2# LVDSB_CLK LVDSB_CLK# LVDSB_DATA3 LVDSB_DATA3# GROUND GROUND VCC/VCC3 VCC/VCC3 VCC/VCC3...

  • Page 70: Figure 4-14: Mini Pci Slot Location

    WAFER-CX700M 3.5" SBC Figure 4-14: Mini PCI Slot Location Page 48...
  • Page 71 WAFER-CX700M 3.5" SBC PIN NO. DESCRIPTION PIN NO. DESCRIPTION PINTD# VCC5 VCC3 PINTC# VCC3SB CLK_MPCI PCI_RST1# VCC3 PCI_REQ2# PCI_GNT2# VCC3 PAD31 PPME# PAD29 PAD30 PAD27 VCC3 PAD25 PAD28 PAD26 PC/BE3# PAD24 PAD23 PAD29 PAD21 PAD22 PAD19 PAD20 PPAR PAD17 PAD18...
  • Page 72 WAFER-CX700M 3.5" SBC PIN NO. DESCRIPTION PIN NO. DESCRIPTION PIRDY# VCC3 PFRAME# PTRDY# SERR# PSTOP# VCC3 PERR# PDEVSEL# PC/BE1# PAD14 PAD15 PAD13 PAD12 PAD11 PAD10 PAD9 PAD8 PC/BE0# PAD7 VCC3 VCC3 PAD6 PAD5 PAD4 PAD2 PAD3 PAD0 VCC5 PAD1 Page 50...

  • Page 73: Power Connector

    WAFER-CX700M 3.5" SBC PIN NO. DESCRIPTION PIN NO. DESCRIPTION VCC3SB Table 4-14: Mini PCI Slot Pinouts 4.2.13 Power Connector CN Label: CN Type: 4-pin AT power connector (1x4) See Figure 4-15 CN Location: CN Pinouts: See Table 4-15 The 4-pin AT power connector is connected to an AT power supply.

  • Page 74: Reset Button Connector

    The ATX power supply enable connector enables the WAFER-CX700M to be connected to an ATX power supply. In default mode, the WAFER-CX700M can only us an AT power supply. To enable an ATX power supply the AT Power Select jumper must also be configured.

  • Page 75: Sata Drive Connectors

    WAFER-CX700M 3.5" SBC Figure 4-17: Reset Button Connector Locations PIN NO. DESCRIPTION Reset Switch Table 4-17: Reset Button Connector Pinouts 4.2.16 SATA Drive Connectors CN Label: SATA1 and SATA2 CN Type: 7-pin SATA drive connectors CN Location: See Figure 4-18...

  • Page 76: Serial Port Connectors

    WAFER-CX700M 3.5" SBC Figure 4-18: SATA Drive Connector Locations PIN NO. DESCRIPTION Table 4-18: SATA Drive Connector Pinouts 4.2.17 Serial Port Connectors CN Label: CN10, CN11 and CN12 10-pin header (2x5) CN Type: See Figure 4-19 CN Location: CN Pinouts: See Table 4-19 The 10-pin serial port connectors provide RS-232 serial communications channels.

  • Page 77: Usb Connectors

    WAFER-CX700M 3.5" SBC Figure 4-19: COM Connector Pinout Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION Data Carrier Direct (DCD) Data Set Ready (DSR) Receive Data (RXD) Request To Send (RTS) Transmit Data (TXD) Clear To Send (CTS) Data Terminal Ready (DTR)

  • Page 78: External Peripheral Interface Connector Panel

    DATA- Table 4-20: USB Port Connector Pinouts 4.3 External Peripheral Interface Connector Panel Figure 4-21 shows the WAFER-CX700M external peripheral interface connector (EPIC) panel. The WAFER-CX700M EPIC panel consists of the following: 2 x RJ-45 LAN connectors 1 x PS/2 connector...

  • Page 79: Lan Connectors

    CN Pinouts: See Table 4-21 The WAFER-CX700M is equipped with two built-in RJ-45 Ethernet controllers. The controllers can connect to the LAN through two RJ-45 LAN connectors. There are two LEDs on the connector indicating the status of LAN. The pin assignments are listed in the...

  • Page 80: Keyboard/Mouse Connector

    WAFER-CX700M 3.5" SBC The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green LED indicates activity on the port and the yellow LED indicates the port is linked. See Table 4-22. STATUS DESCRIPTION STATUS DESCRIPTION...

  • Page 81: Serial Port Connectors

    WAFER-CX700M 3.5" SBC 4.3.3 Serial Port Connectors CN Label: CN16 DB-9 connectors CN Type: CN Location: See Figure 4-21 CN Pinouts: See Table 4-24 and Figure 4-24 The 9-pin DB-9 CN16 serial port connector is connected to RS-232 serial communications devices.

  • Page 82: Figure 4-25: Vga Connector

    WAFER-CX700M 3.5" SBC The WAFER-CX700M has a single 15-pin female connector for connectivity to standard display devices. Figure 4-25: VGA Connector DESCRIPTION DESCRIPTION GREEN BLUE VCC / NC DDC DAT HSYNC VSYNC DDCCLK Table 4-25: VGA Connector Pinouts Page 60...

  • Page 83: Installation

    WAFER-CX700M 3.5" SBC Chapter Installation Page 61...

  • Page 84: Anti-Static Precautions

    WAFER-CX700M and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the WAFER-CX700M. Dry climates are particularly susceptible to ESD. It is therefore critical that whenever the WAFER-CX700M or any other electronic component is...

  • Page 85: Installation Considerations

    WAFER-CX700M in installed. All installation notices pertaining to the installation of the WAFER-CX700M should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the WAFER-CX700M and injury to the person installing the motherboard. 5.2.1 Installation Notices...

  • Page 86: Installation Checklist

    Before and during the installation of the WAFER-CX700M DO NOT do the following: DO NOT remove any of the stickers on the PCB board. These stickers are required for warranty validation.

  • Page 87: Airflow

    The WAFER-CX700M must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface. In a system with an individual power supply unit, the cooling fan of a power supply can also help generate airflow through the board surface.

  • Page 88: Cooling Kit And Dimm Installation

    WAFER-CX700M with three screws. The cooling fan is attached to the heatsink with two metal clips. Three wires attach the cooling fan to the cooling fan power connector on the board. The cooling kit is custom designed for the WAFER-CX700M and should not be replaced with an alternate cooling kit.

  • Page 89: So-Dimm Installation

    Figure 5-1. Figure 5-1: SO-DIMM Installation Step 1: Locate the SO-DIMM socket. Place the WAFER-CX700M on an anti-static pad with the solder side facing up. Step 2: Align the SO-DIMM with the socket. The SO-DIMM must be oriented in such a way that the notch in the middle of the SO-DIMM must be aligned with the plastic bridge in the socket.

  • Page 90: Cf Card Installation

    The WAFER-CX700M can support both CF Type I cards and CF Type II cards. For the complete specifications of the supported CF cards please refer to Chapter 2. To install the a CF card (Type 1 or Type 2) onto the WAFER-CX700M, please follow the steps below: Step 1: Locate the CF card socket.

  • Page 91: Jumper Settings

    OPEN a jumper means removing the Figure 5-3: Jumper Locations plastic clip from a jumper. Before the WAFER-CX700M is installed in the system, the jumpers must be set in accordance with the desired configuration. The jumpers on the WAFER-CX700M are listed below.

  • Page 92: At/Atx Power Supply Selector

    WAFER-CX700M 3.5" SBC Description Label Type AT/ATX power selection CN4 (pins 7 & 8) 2-pin header Clear CMOS 2-pin header LVDS voltage selection 3-pin header RS-232/422/485 selector switch 10 switch selector Table 5-1: Jumpers 5.5.1 AT/ATX Power Supply Selector Jumper Label: CN4 (pins 7 &...

  • Page 93: Clear Cmos Jumper

    See Figure 5-5 Jumper Location: If the WAFER-CX700M fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.

  • Page 94: Lvds Voltage Selection

    Figure 5-5: Clear CMOS Jumper 5.5.3 LVDS Voltage Selection WARNING: Permanent damage to the screen and WAFER-CX700M may occur if the wrong voltage is selected with this jumper. Please refer to the user guide that cam with the monitor to select the correct voltage.

  • Page 95: Rs-232/422/485 Selection Jumper

    WAFER-CX700M 3.5" SBC The LVDS Voltage Selection jumper allows the LVDS screen voltage to be set. The LVDS Voltage Selection jumper settings are shown in Table 5-4. LVDS Voltage Select Description Short 1-2 +3.3V LVDS Short 2-3 +5V LVDS Default Table 5-4: LVDS Voltage Selection Jumper Settings The LVDS Voltage Selection jumper location is shown in Figure 5-6.

  • Page 96: Internal Peripheral Device Connections

    Table 5-5: RS-232/422/485 Selection Jumper Settings The RS-232/422/485 Selection Jumper location is shown in Figure 5-6. Figure 5-7: RS-232/422/485 Selection Jumper 5.6 Internal Peripheral Device Connections The cables listed in Table 5-6 are shipped with the WAFER-CX700M. Quantity Type Audio cable...

  • Page 97: Audio Cable Installation

    0 : 5.6.2 HDD Cable Connection The 44-pin flat IDE cable connects the WAFER-CX700M to an IDE device. To connect an IDE HDD to the WAFER-CX700M please follow the instructions below. Page 75...

  • Page 98: Serial Port Cable Connection

    WAFER-CX700M 3.5" SBC Step 1: Locate the IDE connector. The location/s of the IDE device connector/s is/are shown in Chapter 3. Step 2: Insert the connector. Connect the IDE cable connector to the on-board connector. See Figure 5-9. A key on the front of the cable connector ensures it can only be inserted in one direction.

  • Page 99: Sata Drive Connection

    0 : 5.6.4 SATA Drive Connection The WAFER-CX700M is shipped with two SATA drive cables and one SATA drive power cable. To connect the SATA drives to the connectors, please follow the steps below. Step 1: Locate the connectors.

  • Page 100: Figure 5-11: Sata Drive Cable Connection

    WAFER-CX700M 3.5" SBC Step 2: Insert the cable connector. Press the clip on the connector at the end of the SATA cable and insert the cable connector into the onboard SATA drive connector. See Figure 5-11. Figure 5-11: SATA Drive Cable Connection Step 3: Connect the cable to the SATA disk.

  • Page 101: Usb Cable (Dual Port Without Bracket)

    WAFER-CX700M 3.5" SBC Figure 5-12: SATA Power Drive Connection 5.6.5 USB Cable (Dual Port without Bracket) The WAFER-CX700M is shipped with a dual port USB 2.0 cable. To connect the USB cable connector, please follow the steps below. Step 1: Locate the connectors.

  • Page 102: External Peripheral Interface Connection

    WAFER-CX700M 3.5" SBC Step 3: Insert the cable connectors. Once the cable connectors are properly aligned with the USB connectors on the WAFER-CX700M, connect the cable connectors to the on-board connectors. See Figure 5-13. Figure 5-13: Dual USB Cable Connection Step 4: Attach the USB connectors to the chassis.

  • Page 103: Keyboard/Mouse Y-Cable Connection

    The dual PS/2 connector is connected to the PS/2 Y-cable that came with the WAFER-CX700M. One of the PS/2 cables is connected to a keyboard and the other to a mouse to the system. Follow the steps below to connect a keyboard and mouse to the WAFER-CX700M.

  • Page 104: Lan Connection

    0 : 5.7.3 Serial Device Connection The WAFER-CX700M has a single female DB-9 connector on the external peripheral interface panel for a serial device. Follow the steps below to connect a serial device to the WAFER-CX700M.

  • Page 105: Vga Monitor Connection

    0 : 5.7.4 VGA Monitor Connection The WAFER-CX700M has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the WAFER-CX700M, please follow the instructions below.

  • Page 106: Figure 5-17: Vga Connector

    Once the connectors are properly aligned with the insert the male connector from the VGA screen into the female connector on the WAFER-CX700M. See Figure 5-17. Figure 5-17: VGA Connector Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector.

  • Page 107: Bios Setup

    WAFER-CX700M 3.5" SBC Chapter BIOS Setup Page 85...

  • Page 108: Introduction

    WAFER-CX700M 3.5" SBC 6.1 Introduction A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed.

  • Page 109: Getting Help

    WAFER-CX700M 3.5" SBC Function F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the CMOS changes, only for Main Menu Table 6-1: BIOS Navigation Keys 6.1.3 Getting Help...

  • Page 110: Main

    WAFER-CX700M 3.5" SBC 6.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. BIOS Menu 1: Main System Overview The System Overview lists a brief summary of different system components. The fields in System Overview cannot be changed.

  • Page 111: Advanced

    WAFER-CX700M 3.5" SBC Type: Names the currently installed processor Speed: Lists the processor speed Count: The number of CPUs on the motherboard System Memory: Displays the auto-detected system memory. Size: Lists memory size The System Overview field also has two user configurable fields: System Time [xx:xx:xx] Use the System Time option to set the system time.

  • Page 112: Cpu Configuration

    WAFER-CX700M 3.5" SBC BIOS Menu 2: Advanced 6.3.1 CPU Configuration Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications and configure the CPU. Page 90...

  • Page 113: Bios Menu 3: Cpu Configuration

    WAFER-CX700M 3.5" SBC BIOS Menu 3: CPU Configuration The CPU Configuration menu (BIOS Menu 3) lists the following CPU details: Manufacturer: Lists the name of the CPU manufacturer Frequency: Lists the CPU processing speed FSB Speed: Lists the FSB speed...

  • Page 114: Ide Configuration

    WAFER-CX700M 3.5" SBC instruction results in an exception. When used in combination with the lock instruction (used in multi-processor systems) the exception handler is never called, the processor stops servicing interrupts, and the system has to be rebooted to recover. Processors since the Pentium®...
  • Page 115 WAFER-CX700M 3.5" SBC ATA/IDE Configurations [Compatible] Use the ATA/IDE Configurations option to configure the ATA/IDE controller. Disabled Disables the on-board ATA/IDE controller. Configures the on-board ATA/IDE controller to be in Compatible EFAULT compatible mode. In this mode, a SATA channel will replace one of the IDE channels.

  • Page 116: Ide Master, Ide Slave

    WAFER-CX700M 3.5" SBC 6.3.2.1 IDE Master, IDE Slave Use the IDE Master and IDE Slave configuration menu to view both primary and secondary IDE device details and configure the IDE devices connected to the system. BIOS Menu 5: IDE Master and IDE Slave Configuration...
  • Page 117 WAFER-CX700M 3.5" SBC Auto The BIOS auto detects the IDE disk drive type EFAULT attached to the specified channel. This setting should be used if an IDE hard disk drive is attached to the specified channel. The CD/DVD option specifies that an IDE CD-ROM CD/DVD drive is attached to the specified IDE channel.
  • Page 118 WAFER-CX700M 3.5" SBC drive on the specified channel. If supported the data transfer to and from the device occurs multiple sectors at a time. PIO Mode [Auto] Use the PIO Mode option to select the IDE PIO (Programmable I/O) mode program timing cycles between the IDE drive and the programmable IDE controller.
  • Page 119 WAFER-CX700M 3.5" SBC MWDMA0 Multi Word DMA mode 0 selected with a maximum data transfer rate of 4.2MBps Multi Word DMA mode 1 selected with a maximum data MWDMA1 transfer rate of 13.3MBps MWDMA2 Multi Word DMA mode 2 selected with a maximum data transfer rate of 16.6MBps...

  • Page 120: Super Io Configuration

    WAFER-CX700M 3.5" SBC 32Bit Data Transfer [Enabled] Use the 32Bit Data Transfer BIOS option to enables or disable 32-bit data transfers. Prevents the BIOS from using 32-bit data transfers. Disabled Enabled Allows BIOS to use 32-bit data transfers on supported EFAULT hard disk drives.
  • Page 121 WAFER-CX700M 3.5" SBC Serial Port1 Address [3F8] Use the Serial Port1 Address option to select the Serial Port 1 base address. No base address is assigned to Serial Port 1 Disabled Serial Port 1 I/O port address is 3F8 EFAULT...
  • Page 122 WAFER-CX700M 3.5" SBC Serial Port3 Address [3E8] Use the Serial Port3 Address option to select the base addresses for serial port 3 No base address is assigned to serial port 3 Disabled Serial port 3 I/O port address is 3F8...

  • Page 123: Acpi Configuration

    WAFER-CX700M 3.5" SBC 6.3.4 ACPI Configuration The ACPI Configuration menu (BIOS Menu 7) configures the Advanced Configuration and Power Interface (ACPI) option. BIOS Menu 7: ACPI Configuration [Advanced Power Configuration] Suspend Mode [S1(POS)] Use the Suspend Mode option to specify the sleep state the system enters when it is not being used.

  • Page 124: Apm Configuration

    WAFER-CX700M 3.5" SBC slow refresh; the power supply is in a reduced power mode. 6.3.5 APM Configuration The APM Configuration menu (BIOS Menu 8) allows the advanced power management options to be configured. BIOS Menu 8:Advanced Power Management Configuration Power Supply Type [ATX] Use the Power Supply Type BIOS to specify the kind of power supply used for the system.
  • Page 125 WAFER-CX700M 3.5" SBC the motherboard. Other advanced power features are also enabled. Power is turned on/off directly by the power supply only. Power Button Mode [On/Off] Use the Power Button Mode BIOS to specify how the power button functions. On/Off...

  • Page 126: Remote Access Configuration

    WAFER-CX700M 3.5" SBC Resume on PME# [Disabled] Use the Resume on PME# BIOS option to enable activity on the PCI PME (power management event) controller to rouse the system from a suspend or standby state. Disabled Wake event not generated by PCI PME controller...

  • Page 127: Bios Menu 9: Remote Access Configuration [Advanced]

    WAFER-CX700M 3.5" SBC BIOS Menu 9: Remote Access Configuration [Advanced] Remote Access [Disabled] Use the Remote Access option to enable or disable access to the remote functionalities of the system. Disabled Remote access is disabled. EFAULT Enabled Remote access configuration options shown below...
  • Page 128 WAFER-CX700M 3.5" SBC Terminal Type These configuration options are discussed below. Serial Port Number [COM1] Use the Serial Port Number option allows users to select the serial port used for remote access. System is remotely accessed through COM1 COM1 EFAULT...

  • Page 129: Usb Configuration

    WAFER-CX700M 3.5" SBC NOTE: Identical baud rate setting musts be set on the host (a management computer running a terminal software) and the slave Redirection After BIOS POST [Always] Use the Redirection After BIOS POST option to specify when console redirection should occur.

  • Page 130: Bios Menu 10: Usb Configuration

    WAFER-CX700M 3.5" SBC BIOS Menu 10: USB Configuration USB Configuration The USB Configuration field shows the system USB configuration. The items listed are: Module Version: x.xxxxx.xxxxx USB Devices Enabled The USB Devices Enabled field lists the USB devices that are enabled on the system USB Function [Enabled] Use the USB Function BIOS option to enable or disable the USB function.
  • Page 131 WAFER-CX700M 3.5" SBC 2 USB Ports 2 USB ports are enabled 4 USB ports are enabled 4 USB Ports 6 USB Ports 6 USB ports are enabled EFAULT USB2.0 Ports Enable [Enabled] Use the USB2.0 Ports Enable option to enable and disable USB 2.0.

  • Page 132: Usb Mass Storage Device Configuration

    WAFER-CX700M 3.5" SBC 6.3.7.1 USB Mass Storage Device Configuration Use the USB Mass Storage Device Configuration menu (BIOS Menu 11) to configure USB mass storage class devices. BIOS Menu 11: USB Mass Storage Device Configuration USB Mass Storage Reset Delay [20 Sec] Use the USB Mass Storage Reset Delay option to set the number of seconds POST waits for the USB mass storage device after the start unit command.
  • Page 133 WAFER-CX700M 3.5" SBC 30 Sec POST waits 30 seconds for the USB mass storage device after the start unit command. POST waits 40 seconds for the USB mass storage 40 Sec device after the start unit command. Device ## The Device## field lists the USB devices that are connected to the system.

  • Page 134: Pci/Pnp

    WAFER-CX700M 3.5" SBC responding to INT13h calls that return DL values of 80h or above. CDROM Assumes the CD-ROM is formatted as bootable media. All the devices that support block sizes greater than 512 bytes can only be booted using this option.

  • Page 135: Bios Menu 12: Pci/Pnp Configuration

    WAFER-CX700M 3.5" SBC BIOS Menu 12: PCI/PnP Configuration IRQ# Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral device. Available The specified IRQ is available to be used by PCI/PnP devices Reserved The specified IRQ is reserved for use by Legacy ISA...
  • Page 136 WAFER-CX700M 3.5" SBC IRQ5 IRQ7 IRQ9 IRQ10 IRQ 11 IRQ 14 IRQ 15 DMA Channel# [Available] Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP device. Available The specified DMA is available to be used by...

  • Page 137: Boot

    WAFER-CX700M 3.5" SBC 54KB reserved for legacy ISA devices 6.5 Boot Use the Boot menu (BIOS Menu 13) to configure system boot options. BIOS Menu 13: Boot 6.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (BIOS Menu 14) to configure advanced system boot options.

  • Page 138: Bios Menu 14: Boot Settings Configuration

    WAFER-CX700M 3.5" SBC BIOS Menu 14: Boot Settings Configuration Quick Boot [Enabled] Use the Quick Boot BIOS option to make the computer speed up the boot process. Disabled No POST procedures are skipped Enabled Some POST procedures are skipped to decrease...
  • Page 139 WAFER-CX700M 3.5" SBC AddOn ROM Display Mode [Force BIOS] Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) messages to be displayed. Force BIOS The system forces third party BIOS to display EFAULT during system boot.
  • Page 140 WAFER-CX700M 3.5" SBC LAN Function [LAN1+LAN2] The LAN Function option allows the LAN ports on the board to be disabled or enabled. Both LAN ports are enabled Lan1+Lan2 EFAULT Disabled Both LAN ports are disabled Spread Spectrum Function [Disabled] The Spread Spectrum Mode option can help to improve CPU EMI issues.

  • Page 141: Boot Device Priority

    WAFER-CX700M 3.5" SBC 6.5.2 Boot Device Priority Use the Boot Device Priority menu (BIOS Menu 15) to specify the boot sequence from the available devices. Possible boot devices may include: CD/DVD BIOS Menu 15: Boot Device Priority Settings 6.5.3 Removable Drives Use the Removable Drives menu (BIOS Menu 16) to specify the boot sequence of the available USB devices.

  • Page 142: Security

    WAFER-CX700M 3.5" SBC 2nd Drive USB] NOTE: Only the drives connected to the system are shown. For example, if only one USB device is connected only “1st Drive” is listed. The boot sequence from the available devices is selected. If the “1st Drive” option is selected a list of available USB devices is shown.

  • Page 143: Bios Menu 17: Security

    WAFER-CX700M 3.5" SBC BIOS Menu 17: Security Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password. The default for this option is Not Installed. If a supervisor password must be installed, select this field and enter the password. After the password has been added, Install appears next to Change Supervisor Password.

  • Page 144: Chipset

    WAFER-CX700M 3.5" SBC Clear User Password Use the Clear User Password to clear a user’s password. The default for this option is Not Installed. If a user password must be cleared, use this option. 6.7 Chipset Use the Chipset menu to access the Northbridge and Southbridge submenus.

  • Page 145: Northbridge Configuration

    WAFER-CX700M 3.5" SBC 6.7.1 Northbridge Configuration Use the Northbridge Chipset Configuration menu (BIOS Menu 19) to configure the Northbridge chipset. BIOS Menu 19:Northbridge Chipset Configuration DRAM Frequency [Auto] Use the DRAM Frequency option to specify the DRAM frequency or allow the system to automatically detect the DRAM frequency.
  • Page 146 WAFER-CX700M 3.5" SBC 333MHz Sets the DRAM frequency to 333MHz Sets the DRAM frequency to 400MHz 400MHz 533MHz Sets the DRAM frequency to 533MHz AGP Aperture Size [128MB] Use the AGP Aperture Size option to select the size of the AGP aperture. The aperture is a portion on the PCI memory address range dedicated for use as AGP memory address.

  • Page 147: Southbridge Configuration

    WAFER-CX700M 3.5" SBC CRT + DVI EFAULT LCD + DVI Flat Panel Type [1024x768 18b] Use the Flat Panel Type option to select the type of flat panel connected to the system. Configuration options are listed below. 640 x 480, 18-bit...

  • Page 148: Bios Menu 20:Southbridge Chipset Configuration

    WAFER-CX700M 3.5" SBC BIOS Menu 20:Southbridge Chipset Configuration Serial ATA IDE Controller [IDE] Use the Serial ATA IDE Controller BIOS option to set the mode for the SATA ports. Drives connected to the SATA ports are treated like IDE EFAULT...

  • Page 149: Exit

    WAFER-CX700M 3.5" SBC Auto The High Definition Audio is enabled automatically EFAULT The High Definition Audio is disabled Disabled 6.8 Exit Use the Exit menu (BIOS Menu 21) to load default BIOS values, optimal failsafe values and to save configuration changes.
  • Page 150 WAFER-CX700M 3.5" SBC Discard Changes and Exit Use the Discard Changes and Exit option to exit the BIOS configuration setup program without saving the changes made to the system. Discard Changes Use the Discard Changes option to discard the changes and remain in the BIOS configuration setup program.

  • Page 151: Software Drivers

    WAFER-CX700M 3.5" SBC Chapter Software Drivers Page 129...

  • Page 152: Driver Cd Auto-Run

    Intel® Active Management Technology (AMT) driver Installation instructions are given below. 7.1 Driver CD Auto-run All the drivers for the WAFER-CX700M are on the CD that came with the system. To install the drivers, please follow the steps below. Step 1: Insert the CD into a CD drive connected to the system.

  • Page 153: Figure 7-1: Introduction Screen

    WAFER-CX700M 3.5" SBC Figure 7-1: Introduction Screen Step 3: Click WAFER-CX700M. Step 4: A new screen with a list of available drivers appears (Figure 7-2). Figure 7-2: Available Drivers Page 131...

  • Page 154: Chipset Driver Installation

    WAFER-CX700M 3.5" SBC Step 5: Select the driver to install from the list in Figure 7-2. Detailed driver installation instructions follow below. Step 0: 7.2 Chipset Driver Installation The chipset driver installs drivers needed by the system chipset. To install the system chipset drivers, follow the instructions below.

  • Page 155: Figure 7-4: Chipset Or Platform Drivers

    WAFER-CX700M 3.5" SBC Step 3: Double-click “Chipset or Platform driver Drivers”. Figure 7-4: Chipset or Platform Drivers Step 4: Double-click “VIA_Hyperion Pro_v515A”. Figure 7-5: VIA Hyperion Page 133...

  • Page 156: Figure 7-6: Setup File

    WAFER-CX700M 3.5" SBC Step 5: Double-click ”SETUP.EXE”. Figure 7-6: Setup File Step 6: Click N in the Welcome screen to continue the installation. Figure 7-7: VIA Hyperion Welcome Screen Page 134...

  • Page 157: Figure 7-8: License Agreement

    WAFER-CX700M 3.5" SBC Step 7: Select “I Agree” then N to continue installation. Figure 7-8: License Agreement Step 8: Make sure all the drivers are selected and click N to continue. Figure 7-9: Select Drivers Page 135...

  • Page 158: Figure 7-10: Start Driver Installation

    WAFER-CX700M 3.5" SBC Step 9: Click N to start the driver installation. The installation will take a few moments. Figure 7-10: Start Driver Installation Step 10: The driver installation report screen appears. This screen gives information on whether or not the drivers were installed correctly. Click N to continue.

  • Page 159: Graphics Driver Installation

    WAFER-CX700M 3.5" SBC Step 11: Click F to complete the installation. S t e p 0 : INISH Figure 7-12: Finish Installation 7.3 Graphics Driver Installation The graphics drivers are used by the system chipset for display functions. To install the graphics drivers, follow the instructions below.

  • Page 160: Figure 7-13: Chipset And Graphics

    WAFER-CX700M 3.5" SBC Step 2: Double-click the directory of your operating system (in this case Windows). Figure 7-13: Chipset and Graphics Step 3: Double-click “Integrated Graphics Drivers”. Figure 7-14: Integrated Graphics Drivers Page 138...

  • Page 161: Figure 7-15: 22.00.02A Folder

    WAFER-CX700M 3.5" SBC Step 4: Double-click “22.00.02a”. Figure 7-15: 22.00.02a Folder Step 5: There are four options for installation. Below are the options for each installation. Supports SAMM, TV Large Font. No rotation function. Capture Supports TV Large Font. No SAMM and no rotation function.

  • Page 162: Figure 7-17: Setup File

    WAFER-CX700M 3.5" SBC Step 6: Double-click ”SETUP.EXE”. Figure 7-17: Setup File Step 7: The installation progresses automatically and the Installation Wizard Complete windows appears when done. Click F to finish the installation. INISH Figure 7-18: VIA Hyperion Welcome Screen Step 8: After installation a small S3 icon will appear in the Windows taskbar at the bottom right of the screen.

  • Page 163: Network Adapter Driver Installation

    WAFER-CX700M 3.5" SBC Figure 7-19: S3 Taskbar Icon 7.4 Network Adapter Driver Installation There is no automatic installation for the network adapter drivers. To install the network adapter drivers, please follow the steps for manual driver installation below. Step 1: Select S >>C...

  • Page 164: Figure 7-21: Control Panel

    WAFER-CX700M 3.5" SBC Step 2: Double-click the System icon in the Control Panel window. Figure 7-21: Control Panel Step 3: Select the Hardware tab. Click on D EVICE ANAGER Figure 7-22: System Properties Page 142...

  • Page 165: Figure 7-23: Device Manager

    WAFER-CX700M 3.5" SBC Step 4: Under “Other Devices” devices without drivers are listed. Select the “Ethernet Controller” then click the “Properties” icon to change the driver’s properties. Figure 7-23: Device Manager Step 5: In the “Ethernet Controller Properties” window, select the “General” tab the click on R …...

  • Page 166: Figure 7-25: Hardware Update Wizard

    WAFER-CX700M 3.5" SBC Step 6: The “Hardware Update Wizard” appears. Select “No, not this time.” Click on to continue the driver update process. Figure 7-25: Hardware Update Wizard Step 7: Select “Install from a list or specific location (Advanced)” Click N continue.

  • Page 167: Figure 7-27: Choose Audio Driver

    WAFER-CX700M 3.5" SBC Step 8: Select “Don’t search. I will choose the driver to install.” Click N continue. Figure 7-27: Choose Audio Driver Step 9: Select “Network Adapters” from the list. Click N to continue. Figure 7-28: Driver Selection Page 145...

  • Page 168: Figure 7-29: Default Network Drivers

    WAFER-CX700M 3.5" SBC Step 10: A list of available drivers appears. Don’t select any of these drivers. Click “Have Disk” to select the correct driver file. Figure 7-29: Default Network Drivers. Step 11: Click the B button to select the correct driver from the installation CD.

  • Page 169: Figure 7-31: Driver File Directory

    WAFER-CX700M 3.5" SBC Step 12: Select “D:\2-LAN\Realtek\RTL8110SC” where D: is the CD drive’s letter. Figure 7-31: Driver File Directory Step 13: Double-click the directory for your operating system (in this case Windows). Figure 7-32: Select Operating System Step 14: Double-click the WIN98_ME_2K_XP_XP64 folder.

  • Page 170: Figure 7-34: Installshield Folder

    WAFER-CX700M 3.5" SBC Step 15: Double-click the PCI_InstallShield_5649_060919 folder. Figure 7-34: InstallShield Folder Step 16: Double-click the folder corresponding to your system’s operating system. Figure 7-35: Operating System Folder Step 17: Select the driver file and click O to continue.

  • Page 171: Figure 7-37: Install From Disk

    WAFER-CX700M 3.5" SBC Step 18: Click OK. Figure 7-37: Install From Disk Step 19: Select the ” Realtek RTL8169/8110 Family Gigabit Ethernet NIC” driver. Click to continue. Figure 7-38: New Driver Found Page 149...

  • Page 172: Audio Driver Installation

    WAFER-CX700M 3.5" SBC Step 20: Click F to complete the Installation of the network adapter driver. Repeat INISH the same steps to install the drivers for the second network adapter. S t e p 0 : Figure 7-39: Network Adapter Driver Installation Complete 7.5 Audio Driver Installation...

  • Page 173: Figure 7-40: Audio Driver Folder

    WAFER-CX700M 3.5" SBC Step 2: Double-click the VT1708A folder. Figure 7-40: Audio Driver Folder Step 3: Double-click the folder for your operating system (in this case, Windows). Figure 7-41: Operating System Folder Page 151...

  • Page 174: Figure 7-42: Operating System Version

    WAFER-CX700M 3.5" SBC Step 4: Double-click the folder that corresponds to the specific version of your operating system (in the figure, Windows XP). Figure 7-42: Operating System Version Step 5: Double-click 32-bit for a standard Windows XP install. Figure 7-43: Select 32-bit or 64-bit...

  • Page 175: Figure 7-44: Audio Driver Folder

    WAFER-CX700M 3.5" SBC Step 6: Double-click the HDA_V500b folder. Figure 7-44: Audio Driver Folder Step 7: Double-click SETUP.EXE to start to the InstallShield audio driver installation. Figure 7-45: Audio Driver Setup File Page 153...

  • Page 176: Figure 7-46: Audio Driver Setup Welcome Screen

    WAFER-CX700M 3.5" SBC Step 8: The Audio Driver Setup Welcome screen appears. Select Install/Update then click N to proceed with the installation. Figure 7-46: Audio Driver Setup Welcome Screen Step 9: Click N to install the standard set of drivers.
  • Page 177 WAFER-CX700M 3.5" SBC Step 10: Review the installation settings and click N to continue. Figure 7-48: Page 155...

  • Page 178: Figure 7-49: Audio Driver Installation Complete

    WAFER-CX700M 3.5" SBC Step 11: The drivers are now installed. The drivers only take effect after the compute ris restarted. Select the “Yes, I want to restart my computer now” option then click F to complete the installation. S t e p 0 :...

  • Page 179: Abios Options

    WAFER-CX700M 3.5" SBC Appendix BIOS Options Page 157...
  • Page 180 WAFER-CX700M 3.5" SBC Below is a list of BIOS configuration options in the BIOS chapter. System Overview .........................88 System Time [xx:xx:xx] .......................89 System Date [xx/xx/xx] ......................89 CMPXCHG8B Instruction Support [Enabled] ..............91 ATA/IDE Configurations [Compatible]................93 Legacy IDE Channels [SATA Pri, PATA Sec] ..............93 IDE Master and IDE Slave....................93...
  • Page 181 WAFER-CX700M 3.5" SBC Remote Access [Disabled]....................105 Serial Port Number ......................105 Serial Port Mode........................ 105 Redirection after BIOS POST................... 105 Terminal Type........................106 Serial Port Number [COM1]....................106 Base Address, IRQ [3F8h,4]..................... 106 Serial Port Mode [115200 8,n,1]..................106 Redirection After BIOS POST [Always] ................
  • Page 182 WAFER-CX700M 3.5" SBC Select Display Device [CRT+DVI] ..................124 Flat Panel Type [1024x768 18b] ..................125 Serial ATA IDE Controller [IDE] ..................126 High Definition Audio [Auto].................... 126 Save Changes and Exit ....................127 Discard Changes and Exit....................128 Discard Changes....................... 128 Load Optimal Defaults......................

  • Page 183: Bterminology

    WAFER-CX700M 3.5" SBC Appendix Terminology Page 161...
  • Page 184 WAFER-CX700M 3.5" SBC AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface.
  • Page 185 WAFER-CX700M 3.5" SBC Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory. DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module.
  • Page 186 WAFER-CX700M 3.5" SBC Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid crystal panel in between. LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer.

  • Page 187: Cdigital I/O Interface

    WAFER-CX700M 3.5" SBC Appendix Digital I/O Interface Page 165...

  • Page 188: Introduction

    WAFER-CX700M 3.5" SBC C.1 Introduction The DIO connector on the [MODEL NAME] is interfaced to GPIO ports on the IT8712F Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices.

  • Page 189: Assembly Language Samples

    WAFER-CX700M 3.5" SBC C.3 Assembly Language Samples C.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O input functions is listed below. Sets the digital port as input...
  • Page 190 WAFER-CX700M 3.5" SBC THIS PAGE IS INTENTIONALLY LEFT BLANK Page 168...

  • Page 191: Dwatchdog Timer

    WAFER-CX700M 3.5" SBC Appendix Watchdog Timer Page 169...
  • Page 192 NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash.
  • Page 193 WAFER-CX700M 3.5" SBC NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. Example program: ; INITIAL TIMER PERIOD COUNTER W_LOOP: AX, 6F02H ;setting the time-out value BL, 30 ;time-out value is 48 seconds ;...
  • Page 194 WAFER-CX700M 3.5" SBC THIS PAGE IS INTENTIONALLY LEFT BLANK Page 172...

  • Page 195: Eaddress Mapping

    WAFER-CX700M 3.5" SBC Appendix Address Mapping Page 173...

  • Page 196: Io Address Map

    WAFER-CX700M 3.5" SBC E.1 IO Address Map I/O address Description Range 000-01F DMA Controller 020-021 Interrupt Controller 040-043 System time 060-06F Keyboard Controller 070-07F System CMOS/Real time Clock 080-09F DMA Controller 0A0-0A1 Interrupt Controller 0C0-0DF DMA Controller 0F0-0FF Numeric data processor...

  • Page 197: Irq Mapping Table

    WAFER-CX700M 3.5" SBC E.3 IRQ Mapping Table IRQ0 System Timer IRQ8 RTC clock IRQ1 Keyboard IRQ9 ACPI IRQ2 Available IRQ10 IRQ3 COM2 IRQ11 LAN/USB2.0/SATA IRQ4 COM1 IRQ12 PS/2 mouse IRQ5 SMBus IRQ13 Controller IRQ6 IRQ14 Primary IDE IRQ7 Available IRQ15...
  • Page 198 WAFER-CX700M 3.5" SBC THIS PAGE IS INTENTIONALLY LEFT BLANK Page 176...

  • Page 199: Hazardous Materials Disclosure

    WAFER-CX700M 3.5" SBC Appendix Hazardous Materials Disclosure Page 177...

  • Page 200: Hazardous Materials Disclosure Table For Ipb Products Certified As Rohs Compliant Under 2002/95/Ec Without Mercury

    WAFER-CX700M 3.5" SBC F.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
  • Page 201 WAFER-CX700M 3.5" SBC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl Ethers (CR(VI)) (PBB) (PBDE) Housing Display Printed Circuit Board Metal Fasteners Cable Assembly Fan Assembly Power Supply...
  • Page 202 WAFER-CX700M 3.5" SBC 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元 件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 显示 印刷电路板 金属螺帽 电缆组装 风扇组装 电力供应组装 电池 O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。 X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。...
  • Page 203 WAFER-CX700M 3.5" SBC Index Page 181...
  • Page 204 WAFER-CX700M 3.5" SBC dual RS-232...........76 SATA drive ..........77 SATA drive power ........77 ACPI ............101 CF card ............68 AGP ............124 installation..........68 AT power connector........51 socket ............38 location and pinouts ......51 CF Card socket ..........5 AT power select jumper ......52 chassis ............65 AT/ATX power mode select jumper .....6...
  • Page 205 WAFER-CX700M 3.5" SBC digital input/output .........40 fan............42 hard disk drives LVDS LCD (30-pin)........46 SATA............53 reset button ...........52 HDD LED ...........43 serial port (COM 2)........54 USB (internal)........55 cooling fan ..........42 IDE connector ..........6 IDE connector, 40-pin ........44 location and pinouts.......44 DB-15 connector........83 IDE controller ..........17...
  • Page 206 WAFER-CX700M 3.5" SBC HDD............43 RAID ............53 power.............43 reset button ..........43 LPC bus ..........19, 21 reset button connector .......52 LVDS display ........72, 73 location and pinouts.......52 voltage select ........72, 73 RJ-45 connection ........82 LVDS LCD connector......6, 46 single connector ........82 location and pinouts ......46 RJ-45 connector.........57...
  • Page 207 WAFER-CX700M 3.5" SBC connection ..........82 devices ..........55 serial port connector ......6, 54, 59 port..........18, 55 location and pinouts ......54, 59 USB 1.1 .......... 19, 55 SODIMM ............67 USB 2.0 .......... 19, 55 installation..........67 USB 1.1..........19, 55 specifcations..........67 USB 2.0..........19, 55 USB 2.0 connector........6...

Table of Contents