Product Description And Intended Use; Product Installation - Nice E Star ST Instructions For Installation And Use Manual

ENGLISH
Complete Manual
Notes to manual consultation – Some figures referred to in the text are provided
at the end of the manual.
1
SAFETY WARNINGS AND GENERAL
PRECAUTIONS
1.1 - Safety warnings
• CAUTION! - Important safety instructions. For personal safety, it is impor-
tant to follow these instructions as incorrect installation could cause seri-
ous injury.
Carefully read the instructions before starting work; if in any doubt, con-
tact the Nice Service Centre for assistance.
• CAUTION! - Keep these instructions in a safe pla ce to enable future prod-
uct maintenance and disposal procedures.
• CAUTION! - All installation, connection, program ming and maintenance
operations must be performed exclusively by suitably qualified and skil led
personnel in observance of local legislation, standards and regulations and
the instructions in this manual.
1.2 - Installation warnings
• Before starting installation, ensure that this product is suitable for automating your
sun awning (read paragraph 3.1).
• All product installation and maintenance operations must be performed with the
automation disconnected from the power mains. As a precaution, before starting
work, affix a notice on the disconnect device, with the text "CAUTION! MAINTE-
NANCE IN PRO GRESS".
• Before starting installation operations, move all unnecessary cables away from the
area; also deactivate any mechanisms not required for motor-powered operation
of the awning.
• If the product is installed at a height of less than 2.5 m from the floor or other sup-
port surface, the moving parts must be protected with a suitable covering, to avoid
inadvertent access. To fit such a protection, refer to the awning instruction manual,
and ensure that access is guaranteed for future maintenance operations.
• During installation, handle the product with care, avoiding the risk of crushing,
impact, dropping or contact with any type of liquid; do not drill or insert screws on
the motor exterior and do not place the product in the vicinity of heat sources or
naked flames (fig. 1). This may damage product and cause malfunctions, fire or
hazardous situations. If this occurs, suspend installation immediately and contact
the Nice Technical Assistance.
• During installation, never fit screws along the internal roller section subject to transit
of the tubular motor. This could cause damage to the motor.
• Do not disassemble the product in any way other than as envisaged in this manual.
• Never make any modifications to part of the product other than those specified in
this manual. Operations other than as specified can only cause malfunctions. The
manufacturer declines all liability for damage caused by makeshift modifications to
the product.
1
2 – English 2 – English
• The product power cable is in PVC and is therefore suitable for installation exclu-
sively indoors. If installed outdoors, the cable must be laid in protective ducting.
• If the power cable is damaged, the product cannot be used as the cable cannot be
replaced. Therefore contact the Nice Technical Assistance.
• During system set-up, keep all persons far from the awning when moving.
• The product packaging material must be disposed of in full observance of current
local legislation governing waste disposal
1.3 - Operation warnings
• This product is not designed to be used by persons (including children) whose
physical, sensorial or mental capacities are reduced, or with lack of experience or
skill, unless suitable instructions regarding use of the product have been provided
by a person responsible for safety or under supervision of the latter.
• Children in the vicinity must be supervised at all times to prevent them playing with
the automation.
• Never allow children to play with fixed control de vices. Keep all portable control
devices (remote controls) out of the reach of children.
• During a manoeuvre, check the automation and keep all persons at a safe distance
until the movement has been completed.
• Never activate the awning if maintenance work is being performed (e.g. an adja-
cent window is being cleaned). If the control device is automatic, disconnect the
awning from the power supply.
• Always remember to frequently check the balancing springs and cable wear (if
these mechanisms are present). Do not use the automation if adjustments or
repairs are required. In this case always contact a specialised technician to solve
the problem.
2
PRODUCT DESCRIPTION
AND INTENDED USE
Era Star T is a range of tubular motors designed exclusively to automate various
types of sun awning (see fig. 2). Any other use is strictly prohibited! The manu-
facturer declines all liability for damage resulting from im proper use of the
product and other than as specified in this manual.
Product functional specifications:
– is powered by the mains (see data on the motor's rating plate);
– installed inside the awning winder roller, the protruding face is fixed by means of
the special Nice screws and/or support brackets (not supplied in the pack);
– designed to move the awning up and down;
– supplied with built-in control unit with encoder technology to guarantee electronic
control of movement and limiter precision;
– it is programmed via a wall-mounted keypad (non interlocked buttons) or a TTU
programmer (accessories not supplied in pack);
– is controlled via a wall-mounted pushbutton control panel: it is advisable to use a
momentary or maintained-contact switch with interlocked buttons;
– fitted with a thermal cut-out which, in the event of overheating due to use of the
automation in excess of the set limits, automatically shuts off the power supply and
only restores operation when the temperature returns within the normal range.
2
Awning with articulated
arms, with and without ca-
sing
Arbour
awning
3

PRODUCT INSTALLATION

3.1 - Preliminary checks – Application limit
Before proceeding with installation, perform the following checks:
• Check the condition of product components as soon as they are removed from the
packaging.
• Check suitability of the selected motor by comparing the rated technical specifica-
tions with those of your awning; NEVER install the motor if its specifications
(rated torque, rotation speed and operation time) are not suitable for opera-
tion with your awning. In particular, the motor torque MUST NOT EXCEED
that required to move the awning. Further limitations of use are given in the
"Technical specifications" chapter.
• Check the diameter of the winding roller. This must be chosen according to the
motor torque, as follows:
– for motors that are size "S" (Ø = 35 mm), the minimum inside diameter of the
winding roller must be 40 mm;
Roller awning, with and wi-
thout casing
Awning with straight arms