Avaya 03-300686 Installation And Connection
  1. Manuals
  2. Brands
  3. Avaya Manuals
  4. Network Hardware
  5. 03-300686
  6. Installation and connection
Avaya 03-300686 Installation And Connection

Avaya 03-300686 Installation And Connection

Mdf and telephones
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installing and Connecting the MDF
and Telephones
03-300686
Issue 3
Release 5.0
January 2008

Advertisement

Table of Contents
loading

Related Manuals for Avaya 03-300686

Summary of Contents for Avaya 03-300686

  • Page 1 Installing and Connecting the MDF and Telephones 03-300686 Issue 3 Release 5.0 January 2008...
  • Page 2 Avaya support Avaya provides a telephone number for you to use to report problems or to ask questions about your product. The support telephone number is 1-800-242-2121 in the United States. For additional support telephone...

  • Page 3: Table Of Contents

    ... . . Station (telephone) wiring design ......
  • Page 4 Connectable telephones and consoles ..... Connecting a typical telephone ......
  • Page 5 808A Emergency Transfer Panel and telephone installation examples ......Installing the 808A Emergency Transfer Panel ....
  • Page 6 Testing music-on-hold ......Testing emergency transfer (Avaya S8700 Multi-Connect only) ..
  • Page 7 LED indicators ........Telephone console LEDs ......
  • Page 8 Contents 8 Installing and Connecting the MDF and Telephones...

  • Page 9: Chapter 1: Introduction

    Main Distribution Frames (MDF) and telephones. The procedures explain how you connect media gateways to the MDF and how to connect the MDF to the public switched telephone network (PSTN). This document also explains how to install and wire telephones. The following information is included in this document: Installing the main distribution frame ●...

  • Page 10: Downloading This Book And Updates From The Web

    (http://support.avaya.com). You must have access to the Internet and a copy of Adobe Reader installed on your personal computer. Avaya makes every effort to ensure that the information in this book is complete and accurate. However, information can change after we publish this documentation. Therefore, the Avaya Support Web site might also contain new product information and updates to the information in this book.

  • Page 11: Sending Us Comments

    ● customer network information that you need to configure the control network components with the Avaya Installation Wizard. Get the completed EPW from the Avaya project manager, Avaya software technician, or customer network administrator. A blank EPW is available at the AIW Web site, http://support.avaya.com/avayaiw.
  • Page 12 ● Servers (03-300432). Provides information on how to troubleshoot and replace various components. The following job aids are also available on the CD-ROM Documentation for Avaya ● Communication Manager, Media Gateways and Servers: - Approved Grounds. Provides a description of all approved grounds.

  • Page 13: Chapter 2: Installing The Main Distribution Frame

    If the equipment room does not have one, you must build a main distribution frame (MDF) that connects the media gateways to the building phone network and to the public switched telephone network (PSTN). The tasks include the following: Physical requirements and layout ●...

  • Page 14: Installation Layout

    Installing the main distribution frame Cable Slack Manager A Cable Slack Manager is 32 inches (81.3 centimeters) wide. Slack managers are commonly used in installations consisting of media gateway stacks, such as the SCC1 Media Gateways. Determine the quantity of slack managers by dividing the total length of the MDF in inches (centimeters) by 32 (81.3).
  • Page 15 Sizing 4-pair station cables Use the scale of the floor plan to determine the approximate length of the station cables required per the standard SYSTIMAX wiring concepts. Sizing 25-pair and multiple 25-pair station cables Use the scale of the floor plan to determine the approximate length of each 25-pair station cable.

  • Page 16: Main Distribution Frame Cross-Connect Fields

    Installing the main distribution frame Main distribution frame cross-connect fields Each main distribution frame (MDF) contains a trunk/auxiliary field and a distribution field. The trunk/auxiliary field contains three cross-connect areas: The green field terminates the network interface leads from the central office (CO) and ●...

  • Page 17: Main Distribution Frame Hardware Installation

    This section provides information on installing a main distribution frame (MDF) in an equipment room. It must be installed before connecting media gateways to it and before connecting it to the public switched telephone network (PSTN) outside the building and stations within the building.
  • Page 18 Installing the main distribution frame Figure 2: Example MDF connections (G650 Media Gateway) Figure notes: 1. Rear of Media Gateway 2. Main Distribution Frame (MDF) 3. Port Distribution Field (Purple Field) 4. Station Distribution Field (White Field) 5. Trunk/Auxiliary Field 6.

  • Page 19: Main Distribution Frame Placement

    Main distribution frame placement The preferred location of the MDF is directly behind the media gateways. Figure 3: Typical 110A-type terminal blocks (G650 Media Gateway) using 110A-type terminal blocks. Figure 3: Typical 110A-type terminal blocks (G650 Media Gateway) R IN R IN R IN R IN...

  • Page 20: Main Distribution Frame Labels

    Installing the main distribution frame Main distribution frame labels Figure 4: Label graphic symbols and nomenclature used on labels for the media gateways, cross-connections, information outlets, and cables. The labels are color-coded to identify media gateway wiring: Green — To central office (CO) ●...

  • Page 21: Mounting 110A- Or 110P-Type Terminal Blocks On The Wall

    Mounting 110A- or 110P-type terminal blocks on the wall The 110A-type terminal blocks can be stacked in almost any arrangement at any height or location on the wall. Figure 5: 110A-type terminal blocks (300-pair) arrangement. The distance between the mounting screw holes on the terminal blocks is 10.8 inches (27.4 centimeters).
  • Page 22 Installing the main distribution frame 11. If installing another distribution field terminal block, partially install the first screw for the terminal block, on the line, 7/8-inch (2.2 centimeter) to the right of the previous screw. Partially install the second mounting screw 7-11/16 inch (19.5 centimeter) to right of the screw just installed.
  • Page 23 Figure 6: 110P-type terminal blocks (900-pair) Figure notes: 1. 4 feet (1.22 meters) 2. Horizontal Line 3. 7.68 inches (19.5 centimeters) 4. 47.5 inches (120.6 centimeters) 5. 5.31 inches (13.5 centimeters) Mounting 110A- or 110P-type terminal blocks on the wall r758421b MMR 031496 6.

  • Page 24: Mounting 110P-Type Terminal Blocks On A Frame

    Installing the main distribution frame Mounting 110P-type terminal blocks on a frame The 900-pair 110P-type terminal blocks and the associated patch cord troughs can also be mounted on a free-standing, floor-mounted 1110A2 Apparatus Mounting Frame. See Figure 7: 1110A2 and 1110C1 apparatus mountings Each 1110A2 provides the space to mount five terminal blocks/patch cord troughs on each side of the frame.

  • Page 25: Installing Cable Slack Managers

    Table 1: Apparatus mounting frame ordering information Code number 1110A2 1110C1 1110A1 2110A1 2110B1 Installing Cable Slack Managers Run excess cables on an upper cable ladder (if the MDF connectors are on top) or route them through a cable slack manager that is placed next to the MDF. To install cable slack managers: 1.
  • Page 26 Installing the main distribution frame Cable clamps are required in installations with cable slack managers. At the rear of the media gateways, install two cable clamps using the screws provided. These clamps hold the 25-pair input/output or MDF cables in place. Manager—example for MCC1 Media Gateway Cable Slack Manager—example for SCC1 Media Gateway placement and cable routing.
  • Page 27 Figure 9: Cable routing through Cable Slack Manager—example for SCC1 Media Gateway Figure notes: 1. Top of Media Gateways 2. Cable Clamps 3. Cable Ties (Optional) 4. Power Cord 5. Cable Slack Manager 6. Cable Slack Manager (Cover Removed) 7. Main Distribution Frame (MDF) 8.
  • Page 28 Installing the main distribution frame 28 Installing and Connecting the MDF and Telephones...

  • Page 29: Chapter 3: Installing The Patch Panel

    This chapter is for installations using a patch panel rather than a main distribution frame for connections to the building phone network and the public switched telephone network (PSTN). Patch panels are arrays of RJ45 jacks and associated B25A cables. The panels accommodate 2-wire, 24-port DCP/analog port boards and 8-port analog trunk boards.
  • Page 30 Installing the patch panel Figure 10: Typical RMC patch panel installation Figure notes: 1. Circuit pack amphenol connectors and B25A cables 2. IP server interface adapter and green CAT5 cable 30 Installing and Connecting the MDF and Telephones cadlpat LJK 022502 3.
  • Page 31 Cross-connecting the media gateway to the patch panels Figure 11: Sample cross-connect field patch panel connections Issue 3 January 2008...
  • Page 32 Installing the patch panel 32 Installing and Connecting the MDF and Telephones...

  • Page 33: Chapter 4: Media Gateway Connections To The Mdf

    Chapter 4: Media gateway connections to the MDF Once the main distribution frame (MDF) is installed and wired, you must connect the media gateways to the MDF. Run excess cables on an upper cable ladder (if the MDF connectors are on top) or route them through a cable slack manager that is placed next to the MDF.
  • Page 34 Media gateway connections to the MDF Figure 12: Equipment room cabling labels Figure notes: 1. Purple Label (Port Cable) 2. Blue/Yellow Label (Building and Floor) The top blue/yellow building and floor labels are for cables connecting from the equipment room to a site/satellite location on another floor or in another building.
  • Page 35 Figure 12: Equipment room cabling labels label. Table 3: Cable/connector/building label ordering information information. Table 3: Cable/connector/building label ordering information Description 201A Labels Figure 13: Self-stick label on 25-pair cable connector a 25-pair cable connector. Install the label near the rear of the connector so it is not obscured by the media gateway connector retainers.

  • Page 36: Cable Routing Guidelines

    Media gateway connections to the MDF Cable routing guidelines Figure 14: Cable routing to top terminal blocks blocks on page 37 show typical cable routing from the media gateway to the top and bottom of the MDF, respectively. Figure 14: Cable routing to top terminal blocks Figure notes: 1.
  • Page 37 Figure 15: Cable routing to bottom terminal blocks Figure notes: 1. Main Distribution Frame 2. AC Power Cord (AC-powered media gateways only) 3. Cable Slack Manager Number 1 4. Trunk/Auxiliary Field 5. Station Distribution Field Use these guidelines when routing cables from the media gateway to the MDF. Following these guidelines will maximize use of the cable slack managers and make future cabling additions and changes easier.

  • Page 38: Trunk Cables Among Network Interface, Sneak Fuse Panel, And Media Gateway

    Media gateway connections to the MDF Coil the cable around the columns in the cable slack manager to store cable slack. The ● first run should always go across the full length of the 5 columns in the cable slack manager.

  • Page 39: Installing Connector Cables Between Auxiliary Cabinet And Mdf

    Installing connector cables between auxiliary cabinet and Auxiliary equipment that connects to the MDF can be mounted inside the auxiliary cabinet. The equipment connects to an ED-1E1443-10 (Group 1) intraconnection panel mounted in the cabinet. This intraconnection panel consists of a 110-type 100-pair wiring block. Auxiliary equipment is connected to the 110-type wiring block.
  • Page 40 Media gateway connections to the MDF 40 Installing and Connecting the MDF and Telephones...

  • Page 41: Chapter 5: Mdf Connections To Stations And The Public Switched Telephone Network

    Once the main distribution frame (MDF) is completed and the media gateways are connected to the MDF, you must connect the MDF to stations (telephones) and the public switched telephone network (PSTN). You must also have a provision plan at this time. For more information, see...

  • Page 42: Chapter 5: Mdf Connections To Stations And The Public Switched Telephone Network

    MDF connections to stations and the public switched telephone network Station cables For clarity a station cable is either a 25-pair cable, multiple 25-pair cable, or 4-pair D-inside wire (DIW) run from the equipment room, site/satellite location, or adapter to the information outlets.

  • Page 43: Closets

    4-pair station cable — Use this cable when 4-pair station cables are to be field-terminated on the 110-type terminal blocks in the equipment room or satellite closet and the information outlets require push-on connections. Figure 17: Example of extending 4-pair station cables Figure notes: 1.

  • Page 44: Site Locations

    MDF connections to stations and the public switched telephone network Satellite locations using 110-type hardware Each terminal block has a 3-pair (white field) and a 4-pair (blue field) located on the same terminal block. The 110A-type terminal block that can be used is the 110AE1-75FT. It must be field-terminated to both the white and blue fields.

  • Page 45: 4-Pair Station Circuits

    Figure 18: 4-pair circuit distribution and connectivity on page 47. The station cables must be field-terminated on the on page 47. Table 7: Connectable telephone Figure 19: 4-pair run to equipment Figure 20: 4-pair run to on page 48 shows the 3-pair circuit on page 49.
  • Page 46 MDF connections to stations and the public switched telephone network Figure 18: 4-pair circuit distribution and connectivity Figure notes: 1. Part of Main Distribution Frame (MDF) 2. 3-Pair Connecting Blocks 3. 4-Pair Connecting Blocks 4. Purple Field 5. Blue Field 6.
  • Page 47 Figure 19: 4-pair run to equipment room or satellite location Figure notes: 1. Station Side of MDF or Satellite Location 2. 4-Pair Circuit 3. Blue Field Figure 20: 4-pair run to equipment room or satellite location Figure notes: 1. Part of MDF 2.
  • Page 48 MDF connections to stations and the public switched telephone network Figure 21: 3-pair to 4-pair satellite location connectivity Figure notes: 1. Part of MDF 2. 3-Pair Connecting Blocks 3. Purple Field 4. White Field 5. Patch Cord or Cross-Connect Jumpers 6.
  • Page 49 Figure 22: 3-pair to 4-pair circuit distribution and connectivity Figure notes: 1. Part of Main Distribution Frame (MDF) 2. 3-Pair Connecting Blocks 3. Purple Field 4. Blue Field 5. Patch Cord or Cross-Connect Jumpers 6. To Media Gateway (3-Pair Modularity) Station circuit distribution from equipment room 7.

  • Page 50: Connected Cable Station Adapters

    MDF connections to stations and the public switched telephone network Connected cable station adapters Station adapters are used to provide modular connectivity either directly to a telephone or to an information outlet. See Adapter on page 51. Figure 23: 258A and BR2580A Adapters Figure notes: 1.
  • Page 51 Figure 24: 356A Adapter Figure notes: 1. 356A Adapter Table 4: Adapter ordering information Description 258A Adapter BR2580A Adapter 356A Adapter 400B Adapter 400B2 Adapter ZD8AJ Adapter 451 Adapter - Gray 451 Adapt. - White crdf356 CJL 101296 2. 4-Pair Modular Jacks (6 pins each, connected to 25-pair ribbon connector) Comcode 102605136...

  • Page 52: Completing A Provisioning Plan

    Completing a provisioning plan A provisioning plan should be completed before an installation. The plan determines an appropriate available port circuit on the media gateway for each telephone, trunk, and peripheral connection needed, and any auxiliary power for Basic Rate Interface (BRI) and certain display sets.
  • Page 53 Completing a provisioning plan Figure 25: Port Assignment Record Form Issue 3 January 2008...

  • Page 54: Installing Sneak Current And Off Premise Protection

    MDF connections to stations and the public switched telephone network Installing sneak current and off premise protection Protection from hazardous voltages and currents is required for all off-premises (out of building) trunks, lines, and terminal installations. Protection for incoming analog trunks is required between the incoming RJ21X or RJ2GX network interface and the media gateway for both trunk and off-premise circuit packs.
  • Page 55 Figure 26: Model 507B sneak fuse panel Figure notes: 1. 507B sneak current protector 2. 25-pair male connector (in) Table 5: Sneak fuse panel ordering information Description 157B Connecting Block SCP-110 Protector 507B Sneak Current Fuse Panel 220029 Sneak Current Fuse 25-pair male connector 25-pair female connector Connector cables (B25A male to female) connect the network interface to the sneak fuse panel.
  • Page 56 MDF connections to stations and the public switched telephone network The 507B includes 52 sneak fuses and two cables and can be ordered using PEC code 63210. Use the SCP-110 protectors with 110-type hardware and on the 507B sneak fuse panel. The SCP-110 Protectors can be ordered separately and installed on the 157B connecting block.

  • Page 57: Installing Sneak Fuse Panels

    Installing sneak fuse panels For general information, see Figure 26: Model 507B sneak fuse panel current protection. The panel contains two 25-pair connectors, fuse removal tool, and fifty 220029 sneak fuses (and two spares). See for pinout data. To install sneak fuse panels: 1.

  • Page 58: Installing The Coupled Bonding Conductor

    MDF connections to stations and the public switched telephone network Installing the coupled bonding conductor The coupled bonding conductor (CBC) provides a path to ground for transient energy (for instance, lightning) by virtue of mutual inductance between itself and exposed telcom cables.
  • Page 59 Figure 27: Typical power and ground for a DC power cabinet 10 AWG circuit breaker phase phase 6 AWG Figure notes: 1. Approved Ground 2. 1 AWG Ground Wire 3. CBC Ground Terminal Bar at the MDF (if used) 4. System Single-point Ground Discharge Bar 5.
  • Page 60 MDF connections to stations and the public switched telephone network To provide the coupled bonding protection: 1. Cut a 10 AWG (#25) (2.5 mm single-point ground block (or DC power Ground Discharge Bar) to the MDF CBC block. See Figure 28: Coupled Bonding Conductor 2.
  • Page 61 Figure 28: Coupled Bonding Conductor Figure notes: 1. 25-Pair Tip & Ring Cables to Media Gateways 2. Coupled Bonding Conductor (CBC) Terminal Block 3. Tie Wraps 4. Cable Shield or Six Spare Pairs 5. Ground on Carbon Block Protector or Equivalent 6.

  • Page 62: Installing And Administering The Patch Cord/Jumper

    MDF connections to stations and the public switched telephone network Installing and administering the patch cord/jumper Before starting the patch cord installation, obtain a copy of the Port Assignment Record forms from the customer or marketing representative. See Form on page 53.
  • Page 63 Installing and administering the patch cord/jumper crdf5pr CJL 103096 8. D-Inside Wire Cut Down to Connecting Block 9. 258A Adapter 10. Information Outlet 11. Telephone 12. To Port Connector on Media Gateway (Media Gateway 1, Position B, Slot 03) Issue 3 January 2008...

  • Page 64: Labeling Expansion Control Carrier Cable (Mcc1 Media Gateway Only)

    MDF connections to stations and the public switched telephone network Figure 30: Example 4-pair labeling to information outlet Figure notes: 1. Equipment Room 2. To Central Location for Terminals 1 through 6 3. Blue Row on 110 Terminal Block 4. Purple Row on 110 Terminal Block 5.

  • Page 65: Connecting Expansion Control Carrier Outputs Cable (Mcc1 Media Gateway Only)

    Connecting expansion control carrier outputs cable (MCC1 Media Gateway only) To connect the expansion control carrier outputs cable: 1. Plug the connector cable in the AUX connector on the rear of the expansion control carrier. 2. Route the connector cable through the cable slack manager to the assigned 110-type terminal block in the yellow field of the trunk/auxiliary field.
  • Page 66 MDF connections to stations and the public switched telephone network Figure 31: Connect trunk pairs using concentrator cables Figure notes: 1. Trunk/Auxiliary Field 2. To Expansion Control Carrier AUX Connector (MCC1 Media Gateway only) 3. Concentrator Cable (WP90929, List 1) 4.

  • Page 67: Connecting Trunk Pairs To Media Gateway Using Jumper Wires To Establish 3-Pair Modularity

    Connecting trunk pairs to media gateway using jumper wires to establish 3-pair modularity Figure 32: 3-pair modularity for trunk pairs for 1-pair trunks modularity for trunk pairs for 3-pair Tie trunks media gateway with jumper wires to establish 3-pair modularity. To connect the trunk pairs to the purple field: 1.
  • Page 68 MDF connections to stations and the public switched telephone network Figure 33: 3-pair modularity for trunk pairs for 3-pair Tie trunks Figure notes: 1. Green Field 2. 1-Pair Jumpers 68 Installing and Connecting the MDF and Telephones 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12 3.

  • Page 69: Chapter 6: Installing And Wiring Telephones And Trunks

    Chapter 6: Installing and wiring telephones and trunks The wiring procedures are the same for most Avaya telephones and other equipment. This task list provides wiring examples of similar installation procedures. These are examples only; actual wiring procedures may vary at each site.

  • Page 70: Connecting Telephones

    Connecting an analog station or 2-wire digital station ● Connectable telephones and consoles Table 7: Connectable telephone and consoles that can be connected to an Avaya media gateway. Table 7: Connectable telephone and consoles Telephone and console models 16xx (Avaya one-X Deskphone Value Edition...
  • Page 71 4630SW, 4690 62xx series: 6211, 6219 64xx series: 6402/D, 6408D+, 6416D/D+M, 6424D+/D+M 9040 Avaya TransTalk 96xx series (Avaya one-X Deskphone Edition IP telephones) Avaya Agent Deskphone 16CC Enhanced Attendant Consoles: 302D 603F Avaya Callmaster IV 607A Avaya Callmaster V ACD Console...
  • Page 72 Installing and wiring telephones and trunks Table 7: Connectable telephone and consoles (continued) Telephone and console models 606A Avaya CallMaster VI ACD Console Softphones: Netmeeting H.323 IP Softphone CentreVu IP Agent Softconsole 72 Installing and Connecting the MDF and Telephones...

  • Page 73: Connecting A Typical Telephone

    Connecting a typical telephone The 302D Enhanced Attendant Console is used to describe a telephone connection typically used with the 84xx (4-wire) telephones. The 302D does not require auxiliary power unless it has a 26C1 DXS console or Vacuum Fluorescent Display. The 302D attendant console always requires auxiliary (adjunct) power (-48 VDC).

  • Page 74: Connecting Adjunct Power

    See Auxiliary connector outputs (MCC1 and SCC1 Media Gateways only) Note: Adjunct power can be provided locally at the telephone or console by either the Note: 1151B1 or 1151B2 power supply. Adjunct power can be provided from the equipment room or equipment closet with the 1145B power unit. See and wiring telephone power supplies and installation procedures.

  • Page 75: Connecting An Analog Station Or 2-Wire Digital Station

    4. Install cross-connect jumpers to connect the pins from the 2-wire digital station to the appropriate pins on the MM711 Media Module. shows a printout chart for two-wire stations. 5. Administer using Administrator Guide for Avaya Communication Manager (03-300509). Connecting telephones r749428 KLC 060396 4.

  • Page 76: Analog Tie Trunk Example

    This example shows how to connect analog tie trunk wiring from one IP Connect or Multi-Connect configuration to another one or any other Avaya configuration. 1. Set the option switches on the port circuit pack (such as TN760E Tie Trunk circuit pack).

  • Page 77: Digital Tie Trunk Example

    Names of the tie trunk leads must be determined from the manufacturer or supplier of the external trunk circuit. 5. Administer on the Trunk Group screen on Avaya Site Administration (ASA). See the Administrator Guide for Avaya Communication Manager (03-300509) for more details.

  • Page 78: Ds1 Tie Trunk Example

    Installing and wiring telephones and trunks Figure 38: Digital Tie Trunk wiring Figure notes: 1. External Trunk 2. Digital Trunk Circuit Pack 3. LO DS1 tie trunk example Digital Signal Level 1 (DS1) tie trunks provide a 1.544 Mbps (T1) or 2.048 Mbps (E1) digital data service between two collocated configurations or between the configuration and a data network.

  • Page 79: Ds1 Interface Trunks Using T1 Channel Service Unit

    Note: A 3150 CSU is shown, a 120A Integrated CSU (ICSU) may be used. Note: Contact your Avaya representative for maximum cabling distances for the 3127 series CSU or the 120A ICSU. Figure 39: Typical connections to channel service unit Figure notes: 1.
  • Page 80 Installing and wiring telephones and trunks Table 9: DS1 cables Connector cable C6C connector cable C6D connector cable C6E connector cable C6F connector cable 80 Installing and Connecting the MDF and Telephones Description and usage 50-feet (15 meters) shielded cable equipped with a 50-pin male connector on one end and a 15-pin male connector on the other end.

  • Page 81: Media Gateways Only)

    Table 11: Auxiliary lead appearances at AUX connector control carrier outputs cable pinouts ● pinouts for an external alarm ● port circuit pack and telephone pin designations ● The control carrier AUX connector outputs include: Two inputs for external alarm signals ●...
  • Page 82 Installing and wiring telephones and trunks Table 11: Auxiliary lead appearances at AUX connector (continued) Color R-BR BR-R BK-BL BL-BK BK-O O-BK BK-G G-BK BK-BR BR-BK BK-S S-BK Y-BL BL-Y Y-BR BR-Y V-BL BL-V 82 Installing and Connecting the MDF and Telephones Pinouts Output Not Connected...
  • Page 83 Auxiliary connector outputs (MCC1 and SCC1 Media Gateways only) Table 11: Auxiliary lead appearances at AUX connector (continued) Color Pinouts V-BR BR-V *. Color designation is the main wire color and the color of the stripe on the wire. The following wire colors apply: W White BL Blue O Orange...

  • Page 84: Three-Pair And Four-Pair Modularity

    Installing and wiring telephones and trunks Three-pair and four-pair modularity Figure 40: 3-pair and 4-pair modularity data terminal. Most terminals connect to an information outlet (modular jack) installed at the work location. Make the connections from the port circuit pack to the modular jacks, as shown in Figure 40: 3-pair and 4-pair modularity jack.

  • Page 85: Adjunct Power Connection Locations

    2. If only ten of the telephones need adjunct power, install a bulk power supply at the satellite location. 3. If only one telephone needs adjunct power, install the individual power supply at the work location. Figure 41: Example adjunct power connections Figure notes: 1.

  • Page 86: Attendant Console Example

    Installing and wiring telephones and trunks Attendant console example Perform these tasks to install an attendant console Installing the attendant console ● Installing the 26B1 Selector Console ● Attendant console cabling distances, local and phantom power A console’s maximum distance from the media gateway is limited. The maximum distance for a 302D console is as shown in Table 13: Attendant console cabling distances Enhanced Attendant...

  • Page 87: Hard-Wire Bridging

    Dual wiring of 2-wire and 4-wire endpoints Do not simultaneously wire a 2-wire and 4-wire endpoint to the same equipment location in an MDF. The Avaya configurations use separate circuit packs to interface 2- and 4-wire endpoints. Installing the attendant console To install the attendant console: 1.

  • Page 88: Installing The 26B1 Selector Console

    2. Route the cable to the attendant console and connect to the DXS/BLF jack. 3. Attach labels according to the Attendant Console form. 4. Administer the console using Administrator Guide for Avaya Communication Manager (03-300509). Connecting external alarm indicators and auxiliary power Alarms can be generated on adjunct equipment, sent to the server, and recorded and reported as “external alarms.”...
  • Page 89 5 mA minimum. 2. Connect an external alarm output (Green-White and White-Green). 3. Note which device connects to which alarm and give this information to your Avaya representative for troubleshooting purposes. Connecting external alarm indicators and auxiliary power...

  • Page 90: Installing Off-Premises Station Wiring

    *. For additional information on the auxiliary field on the Main Distribution Field, see Figure 49: Connections for telephone used for emergency transfer Figure 50: Connections for telephone used for emergency transfer and as normal extension Installing off-premises station wiring The local telephone company provides cabling outside the building for off-premises stations.

  • Page 91: Off-Premises Or Out-Of-Building Stations

    4. Install a green label on the terminal block to identify the remote location. 5. Administer per the Administrator Guide for Avaya Communication Manager (03-300509). Off-premises or out-of-building stations Out-of-building campus stations are telephones not physically located in the same building as the equipment room but located on the same property.
  • Page 92 Installing and wiring telephones and trunks Figure 44: Connections for 1 to 8 out-of-building analog telephones Figure notes: 1. Locally Engineered Cables and Equipment 2. Out-of-Building Wiring 3. 25-Pair Connector 4. Multi-Pair Protector Units (Primary Protectors with Heat Coils or Equivalent with Sneak Current Protection) 5.

  • Page 93: Off-Premises Protection Requirements

    Figure 45: Connections to 24 out-of-building telephones Figure notes: 1. Locally Engineered Cables and Equipment 2. 25-Pair Connector 3. Multi-Pair Protector Units (Primary Protectors with Heat Coils or Equivalent with Sneak Current Protection) 4. B25A Cable (Male to Female) 5. Concentrator Cable (WP90929 List 1) 6.

  • Page 94: Telephone Restrictions For Exposed Environments

    3C1S (solid state) *. The 3-type protectors should be used only if they are already part For catalogs and ordering information, go to the Avaya Cable Management Systems for Service Providers Web site (http://connectivity.avaya.com/exchangemax/) and click Products & Solutions. Telephone restrictions for exposed environments Analog telephones connected to TN746B Analog Line circuit packs cannot be installed in an exposed environment.

  • Page 95: Installing The Itw Linx Enhanced Protector

    When a protector is used, the telephone must be locally powered by an external power supply or through the AC power cord provided with some telephones. The protector is installed on the equipment side of the protection in both buildings.

  • Page 96: Emergency Transfer Units And Associated Telephones

    Installing and wiring telephones and trunks Figure 41: Example adjunct power connections at trunk/auxiliary field on page 96. Figure 46: Connections at trunk/auxiliary field Figure notes: 1. To Network Interface Facility 2. To Control Carrier Auxiliary Connector Emergency transfer units and associated telephones An 808A Emergency Transfer Panel mounted next to the trunk/auxiliary field provides emergency transfer capability.

  • Page 97: Emergency Transfer Panel And Telephone Installation Examples

    The panel can be installed on any mounting frame in either a vertical or horizontal position. The housing has ears for screw-mounting and cutouts for snap-mounting the unit in an 89-type mounting bracket. See Task List: Typical Emergency Transfer Panel and Telephone Installation: Installing the 808A Emergency Transfer Panel ●...
  • Page 98 Installing and wiring telephones and trunks Figure 47: 808A Emergency Transfer Panel Figure notes: 1. 808A Emergency Transfer Panel 2. Circuit Start Selection Switches 98 Installing and Connecting the MDF and Telephones EMERGENCY TRANSFER PANEL POWER TRUNK/TEST SWITCHES CIRCUIT TRUNK OPTION LOOP GROUND START...

  • Page 99: Installing The 808A Emergency Transfer Panel

    3 and 4 are used for circuit 2, and so forth. See page 101. 3. For loop start, set the switches to the left. For ground start, set the switches to the right. 808A Emergency Transfer Panel and telephone installation examples 4. 25-Pair Male Connector 5. Circuit Start Switches...
  • Page 100 6. On the trunk identification label at the bottom of the panel, record the trunk line, extension, and location for each circuit. 7. To each telephone designated as an emergency terminal, attach a label identifying it as such. The labels are provided with the unit.
  • Page 101 808A Emergency Transfer Panel and telephone installation examples Table 18: Pin assignments for 25-pair connector W-BL BL-W W-BR BR-W R-BL BL-R Table 17: Trunk/test switches Switch Circuit number number Not Used Test Switch TTC1 Tip-PBX Trunk Circuit 1 RTC1 Ring-PBX Trunk Circuit 1...
  • Page 102 Installing and wiring telephones and trunks Table 18: Pin assignments for 25-pair connector (continued) 102 Installing and Connecting the MDF and Telephones TLC2 Tip-PBX Line Port 2 RLC2 Ring-PBX Line Port 2 TST2 Tip-Emergency Terminal 2 RST2 Ring-Emergency Terminal 2 R-BR TTC3 Tip-PBX Trunk Circuit 3...
  • Page 103 808A Emergency Transfer Panel and telephone installation examples Table 18: Pin assignments for 25-pair connector (continued) V-BR BR-V Figure 49: Connections for telephone used for emergency transfer 2822 ALARM MONITORS Figure notes: 1. To Network Interface Circuitry 2. To TN747B (or Equivalent) Central Office Trunk Circuit Pack 3.

  • Page 104: Installing Telephones Used Only For Emergency Transfer (Trunk/Auxiliary Field)

    Installing and wiring telephones and trunks Figure 50: Connections for telephone used for emergency transfer and as normal extension 2820 XR 1m AL 1M ALARM MONITORS Figure notes: 1. To Network Interface Facility 2. To Blue or White Station Distribution Field 3.

  • Page 105: Installing Telephones Used For Emergency Transfer And As Normal Extension (Trunk/Auxiliary Field)

    3. Connect CO trunk leads from the green field to TK terminals on the yellow emergency transfer row/connecting block for each trunk. 4. Connect telephone leads from the purple analog line circuit pack row/ connecting block to the LC terminals on the yellow emergency transfer row/connecting block for each telephone.

  • Page 106: Installing External Ringing

    1. Wire the ringing device to the information outlet as shown in modularity on page 106 and 2. Administer per the Administrator Guide for Avaya Communication Manager (03-300509). Figure 51: 3-pair and 4-pair modularity Figure notes: 1. Port Circuit Pack 2.

  • Page 107: Installing The Queue Warning Indicator

    Installing the queue warning indicator The connections for the queue warning indicator are the same as external ringing. An AC indicator (lamp) such as a 21C49 can be used in a uniform call distribution/direct departmental calling (UCD/DDC) queue. The lamp is connected to an information outlet. The media gateway side of the MDF is connected to an analog line circuit pack located in a port carrier.
  • Page 108 Installing and wiring telephones and trunks 108 Installing and Connecting the MDF and Telephones...

  • Page 109: Chapter 7: Installing And Wiring Telephone Power Supplies

    These are examples only and actual wiring procedures may vary at each site. Note: See Adding New Hardware for Avaya Servers and Gateways (03-300684) to Note: install the necessary peripheral equipment. The power is provided to telephones or consoles either locally or centrally.

  • Page 110: Important Warning For 1145B2 Power Supply

    Installing and wiring telephone power supplies Installing the battery mounting/wiring Installing the expanded power distribution unit Powering up and testing the power supply Wiring the 1146B2 Power Distribution Unit Resetting LEDs on power distribution unit Important warning for 1145B2 power supply WARNING: Important Safety Instructions follow.

  • Page 111: Mounting The 1145B2/1146B2 Power Supply

    Power down the power unit (see label on power unit on how to do this) and refer servicing ● under the following conditions: If liquid has been spilled into any of the products ● If any of the products have been exposed to water ●...
  • Page 112 Installing and wiring telephone power supplies Figure 52: 1145B2/1146B2 mounting arrangement Figure notes: 1. Wall Mounting Plate 2. Battery (1149B Shown) 3. 1146B2 Power Distribution Unit 4. 1145B2 Power Unit 112 Installing and Connecting the MDF and Telephones 1149 Battery...
  • Page 113 Figure 53: Expanded power distribution unit Figure notes: 1. Wall Mounting Plate 2. Battery (1149B shown) 3. Second 1146B2 Power Distribution Unit 4. “T” Cable (H600-347-G7) 1149 Battery On Battery Reserve 1145 Power Unit Charging Battery Output Power On 5. First 1146B2 Power Distribution Unit 6.

  • Page 114: Installing The Wall-Mounting Plates

    Installing and wiring telephone power supplies Installing the wall-mounting plates The top plate is used for mounting the back-up battery. The bottom plate is used to mount the power supply and distribution units. The plates can be rack-mounted using standard rack-mounting brackets.

  • Page 115: Installing The Battery Mounting/Wiring

    Installing the battery mounting/wiring Three types of back-up batteries are used. See for the battery type and rating. To install the battery mounting and wiring: 1. Insert two #10-32 x 1/2-inch shoulder screws into the top designated battery holes on the wall mounting plate.

  • Page 116: Powering Up And Testing The Power Supply

    Installing and wiring telephone power supplies Figure 53: Expanded power distribution unit distribution unit. To install the expanded power distribution unit: 1. Set the spacer bracket onto the mounting plate and secure with the #8-32 x 1/2-inch shoulder screws. The spacer bracket is not shown in the figure but is installed behind the top power distribution unit.

  • Page 117: Wiring The 1146B2 Power Distribution Unit

    Wiring the 1146B2 Power Distribution Unit Wire endpoints to the 1146B2 while power from the 1145B2 is on. A red LED lights if its associated circuit is connected to shorted wiring or to a shorted telephone. To wire the 1146B2 Power Distribution Unit: 1.

  • Page 118: Resetting Leds On Power Distribution Unit

    Installing and wiring telephone power supplies Figure 54: Typical wiring to a telephone Figure notes: 1. Power Supply Kit 2. 2.5, 5.0, or 8.0 Amp Hour Battery 3. 1146B2 Distribution Unit 4. 1145B2 Power Supply 5. Circuits 1-16 6. Circuits 17-32 7.

  • Page 119: 1152A1 Mid-Span Power Distribution Unit

    1152A1 Mid-Span Power Distribution Unit The 1152A1 Mid-Span Power Distribution Unit (PDU) is an Ethernet power supply that provides power to up to 24 46xx-series IP telephones or wireless LAN (WLAN) access points. This unit is used with a 10/100BaseTx standard Ethernet network over a standard TIA/EIA-568 Category 5, 6 or 6e cabling plant.

  • Page 120: Using The 1152A1 Power Distribution Unit

    The 1152A1 PDU is used to power the 46xx series of IP telephones in addition to providing 10/ 100 megabits per second Ethernet connection. Generation 1 Avaya IP telephones can receive power from the 1152A1 via an in-line adapter. This adapter provides the resistive signature so that the 1152A1 allows power to flow to the telephone.

  • Page 121: Connecting The Cables

    For Data-In ports connect the Ethernet cable leading from the Ethernet Switch/Hub to the Data port. For Data & Power Out ports, connect the Ethernet cable leading to the telephone or other end device to the corresponding Data & Power port.

  • Page 122: Connecting Cables To Telephones And Other End Devices

    It is Power over LAN Enabled or not. ● If not, you may safely connect the telephone; however, the port supplies no power and functions as a normal Ethernet data port. It requires an external splitter or whether it requires only a single RJ45 connection.

  • Page 123: 1152B Mid-Span Power Distribution Units

    Ethernet network. The 1152B PDUs eliminate the need to connect each Ethernet Data Terminal, such as an IP Telephone set, to an AC power outlet in addition to the data port. The system also removes the need for power cables, local AC wall adapters and the use of a dedicated UPS for each IP telephone.

  • Page 124: Important 1152B Pdu Safety Instructions

    Installing and wiring telephone power supplies The 1152B PDU complies with the Underwriters Laboratories Inc. (UL) standard UL 60950-1, Edition. Important 1152B PDU Safety Instructions Please read the following helpful tips. Retain these tips for later use. When using this switch, the following safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons: Read and understand all instructions.

  • Page 125: Using The 1152B Pdus

    10/100 megabits per second Ethernet connection. Generation 1 Avaya IP telephones can receive power from the 1152B using an in-line adapter. This adapter provides the resistive signature so that the 1152B allows power to flow to the telephone.

  • Page 126: Connecting Cables To Telephones And Other End Devices

    For Data-In ports connect the Ethernet cable leading from the Ethernet Switch/Hub to the Data port. For Data & Power Out ports connect the Ethernet cable leading to the telephone or other end device to the corresponding Data & Power port.
  • Page 127 2. Connect the opposite end of the same cable to the RJ45 wall outlet. 3. On the front panel of the 1152B PDU, monitor the response of the corresponding port LED. If it lights up GREEN, the unit has identified your telephone as a Power over LAN telephone. 1152B Mid-Span Power Distribution Units...

  • Page 128: C360 Converged Stackable Switches

    Installing and wiring telephone power supplies C360 converged stackable switches The Avaya C360 series of converged stackable switches include four main products: C363T C363T-PWR C364T C364T-PWR The C360 converged stackable switches comply with the Underwriters Laboratories Inc. (UL) standard UL 60950.

  • Page 129: Using The C360 Switch

    This characteristic is similar to how modules can be swapped in a modular switching chassis. Avaya C360 switches are multilayer switches and can be upgraded with a license to provide routing (Layer3) functionality. The C360 switches can be mounted in a standard 19-inch (48-centimeter) rack or mounted on a wall.

  • Page 130: Connecting The C360 Stackable Switches

    ● To provide more than 200 watts for the power over Ethernet ports ● Note: Please see the Avaya C360 Manager User Guide and the Quick Start for Note: Hardware Installation Avaya C360 Converged Stackable Switches (03-300148) for more information.

  • Page 131: Connecting The Cables

    To connect IP telephones, PCs, servers, routers, workstations, and hubs. 1. Connect the Ethernet connection cable (not supplied) to a 10/100 megabits per second port on the front panel of the Avaya C360 series switch. Note: Use standard RJ45 connections and a CAT5 cable for 100 megabits per second Note: operation.

  • Page 132: Important Safety Instructions For 1151B1 And 1151B2 Power Supplies

    Attendant Console that requires auxiliary power for its display. The unit can supply power to adjunct equipment such as S201A and CS201A speakerphones or a 500A Headset Adapter attached to any currently manufactured analog, DCP, or ISDN-T telephone equipped with an adjunct jack.

  • Page 133: Connecting The 1151B1 Or 1151B2 Power Supplies

    The 1151B1 is a standard (no battery backup) power supply unit. The 1151B2 is a battery backup version of the 1151B1. Either power supply can support one telephone with or without an adjunct. The maximum loop range is 250 feet (76 meters). Two modular jacks are used.
  • Page 134 Installing and wiring telephone power supplies 134 Installing and Connecting the MDF and Telephones...

  • Page 135: Chapter 8: Testing The Complete Configuration

    LED indicators on page 147 for information regarding the LED status indicators for the Avaya Ethernet switch(es), uninterruptible power supplies (UPSs), and different circuit packs. Note: Circuit pack positions are usually given by cabinet, and slot. They may also be Note: given by port.

  • Page 136: Testing Port Network Equipment

    1. Type status port-network number <1-64> and press Enter. 2. Verify the screen displays a Port Network Status screen similar to network status screen for Cabinet 1—Avaya S8500 Verify these service states: 136 Installing and Connecting the MDF and Telephones on page 137.

  • Page 137: Checking Circuit Pack Configuration

    Figure 60: Sample port network status screen for Cabinet 1—Avaya S8500 status port-network 1 Major Minor PN Alarms Alarms Alarms TDM Service Control State Channel Command: Checking circuit pack configuration The list configuration report provides a list of circuit packs connected to the configuration and recognized by the software.

  • Page 138: Testing The Tn2312Bp Internet Protocol Server Interface Circuit Pack

    DS1 INTERFACE Testing the TN2312BP Internet Protocol Server Interface circuit pack To test the TN2312BP Internet Protocol Server Interface circuit pack using Avaya Site Administration: 1. Type test ipserver-interface UUC and press Enter to test all clock and packet interface components within the IPSI circuit pack.

  • Page 139: Testing Expansion Interface Circuit Packs, If Used

    Figure 62: Sample IPSI 01A test results screen — Page 1, Avaya S8700 Multi-Connect test ipserver-interface 1a Port Maintenance Name TONE-BD TONE-BD 01A0201 ETR-PT 01A0201 ETR-PT 01A0202 ETR-PT 01A0202 ETR-PT 01A0203 ETR-PT 01A0203 ETR-PT 01A0204 ETR-PT 01A0204 ETR-PT 01A0205 ETR-PT...

  • Page 140: Testing Time Division Multiplexing Bus For Each Port Network

    Testing the complete configuration Figure 63: Sample test results for Expansion Interface Board 2A01 TEST RESULTS Port Maintenance Name 02A01 EXP-INTF 02A01 EXP-INTF 02A01 EXP-INTF 02A01 EXP-INTF 02A01 EXP-INTF 02A01 EXP-INTF Testing time division multiplexing bus for each port network To check each TDM bus for each port network (PN) in the configuration.

  • Page 141: Testing Expansion Interface Exchange, If Used, For Each Port Network

    Testing expansion interface exchange, if used, for each port network If the configuration is critical reliability, test the expansion interface exchange for each PN: 1. Type status port-network number <1-64> and press Enter. This displays the standby expansion link. See before expansion link is set on page 2.

  • Page 142: Testing Telephones And Other Equipment

    Testing the complete configuration Figure 66: Sample of port network status after expansion link is set status port-network Major Minor PN Alarms Alarms Alarms TDM Service Control State Channel Command: Saving translations, if required Type save translations and press Enter to save the translations to the hard drive. ●...

  • Page 143: Making Test Calls

    Testing connectivity to the LAN ● Making test calls Make two calls from one telephone to another telephone. Make the first call by dialing a telephone and make the second call by dialing a trunk access code and a listed directory number (LDN).

  • Page 144: Testing Selector Console

    Testing the complete configuration Testing selector console To check that all selector console lamps are operational and make a call to a telephone in the configuration: 1. Simultaneously press and hold Ringer Volume up and POS BUSY on the attendant console.

  • Page 145: Record An Announcement

    Testing emergency transfer (Avaya S8700 Multi-Connect only) Put configuration in emergency transfer mode and make call using emergency transfer telephone. There may be up to four Emergency Transfer panels on a wall in the phone closet, depending on the configuration.

  • Page 146: Testing Terminating Trunk Transmission

    Testing the complete configuration Testing terminating trunk transmission The terminating trunk transmission test provides for extension number access to 3 tone sequences that can be used for trunk transmission testing from the distant end of the trunks. To test terminating trunk transmission: 1.

  • Page 147: Testing Connectivity To The Lan

    Alarms are communicated to users and technicians by entries in the alarm and sys logs and the lighting of LEDs located on the attendant console, on all circuit packs, and, optionally, on customer-designated telephones. More detailed information is available here for: Telephone console LEDs ● DS1 Converter circuit pack LEDs ●...

  • Page 148: Telephone Console Leds

    Testing the complete configuration Telephone console LEDs Telephones and attendant consoles have some alarm LEDs that must be checked out. Attendant console LEDs The console has two red LEDs, labeled “ALM” and “ACK”. The ALM LED lights steadily when there is a major or minor alarm at the server. The ACK LED lights steadily if the alarm has been successfully reported to INADS.
  • Page 149 Figure 67: TN1654 DS1 Converter circuit pack LEDs Figure notes: 1. Alarm LED (Red) 2. Test LED (Green) 3. Busy LED (Yellow) The yellow LED indicates the state of the fiber interface, the fiber channel, the control channel, and the communications link to the SPE in the following manner and order of priority. See Table 23: DS1 Converter yellow LED flashing Table 23: DS1 Converter yellow LED flashing states LED on...

  • Page 150: Span Leds

    Testing the complete configuration Table 23: DS1 Converter yellow LED flashing states (continued) LED on LED off solid on solid off SPAN LEDs The four SPAN LEDs indicate the status of the four T1/E1 facilities. A SPAN LED is in one of the following states: Solid on yellow: Facility is operational and alarm free.

  • Page 151: Index

    Index Numerical ..110A-type terminal blocks (G650) 110P-type terminal blocks, frame-mounting ....110-type hardware 110-type hardware, SCP-110 sneak current protection .
  • Page 152 Index installing between cabinet and MDF ... . outputs for control carrier cables, installing between auxiliary cabinet and MDF cabling ....installing trunk cables .
  • Page 153 ....sneak fuse panels telephone power supplies ....procedures telephones used for emergency transfer .
  • Page 154 ....making test calls ... telephone installation examples ... . telephone pin designations telephones .
  • Page 155 ....telephone connection wiring telephone power supplies ....procedures .
  • Page 156 Index 156 Installing and Connecting the MDF and Telephones...

Table of Contents