Access Menu - BFT THALIA P Installation Manual

x 2
add. start
hidden butt
Add. 2ch
hidden butt
erase 64
language
autoset
l. s w adj opm1
2 1
opm2
2 1
clm2
-
2 1
clm1
-
2 1
ersu
o
+/-
Control unit
software version
stat
vers OK bft . . .
+/-
- + No total
manoeuvres(in hundreds)
n. cycles OK 0000
+/-
- +
No radio control
devices memorised
00
n. remotes OK
+/-
- +
List of last 30 errors
01.33
err OK
02.01
........
30.15
+/-
0---
password
ACCESS MENUS Fig. 1
See PARAMETERS MENU
See LOGIC MENU
release desired button
release
desired button
See RADIO MENU
Diagnostics
code
STRE START E external start input activated
STRI START I internal start input activated
OPEN OPEN input activated
CLS CLOSE input activated
PED PED pedestrian input activated
TIME TIMER input activated
STOP input activated
STOP
PHOT photocell input activated
PHOT
PHOT OP opening photocell input activated
PHOP
PHCL PHOT CL closing photocell input activated
BAR BAR safety edge input activated
SWC1 SWC1 motor 1 closing limit switch input activated
SWO1 SWO1 motor 1 opening limit switch input activated
SWC2 SWC2 motor 2 closing limit switch input activated
SWO2 SWO2 motor 2 opening limit switch input activated
The board is standing by to perform a complete opening-
closing cycle uninterrupted by intermediate stops in
SET
order to acquire the torque required for movement.
WARNINg! Obstacle detection not active
Photocell test failed
ER01
ER02 Safety edge test failed
ER03 Opening photocell test failed
ER04 Closing photocell test failed
er06 8k2 safety edge test failed
ER1x Board hardware test error
*
ER2x Encoder error
*
ER3x * Reverse due to obstacle - Amperostop
Thermal cutout
ER4x *
Communication error with remote devices
ER5x *
Running off battery
ER61
ER7x Internal system supervision control error.
*
Solenoid lock output overload
ERF9
Ersw Error during limit switch adjustment
*X= 0, 1, .., 9, A, B, C, D, E, F
150-
10--
35. 4 0
DESCRIPTION
1520
prg
Scroll up
Scroll down
Con rm/Switch on display
Exit Menù
Instantaneous force motor 2
Instantaneous force motor 1
NOTES
Check photocell connection and/or logic settings
Check safety edge connection and/or logic settings
Check photocell connection and/or param-
eter/logic setting
Check photocell connection and/or param-
eter/logic setting
Check safety edge connection and/or param-
eter/logic settings
- C h e c k c o n n e c t i o n s t o m o t o r
- Hardware problems with board (contact
technical assistance)
- M o t o r p o w e r o r e n c o d e r s i g -
n a l c a b l e s i n v e r t e d / d i s c o n n e c t e d .
- Actuator movement is too slow or stopped
with respect to programmed operation.
Check for obstacles in path
Allow automated device to cool
Check connection with serial-connected
accessory devices and/or expansion boards
--
Try switching the board off and back on again.
If the problem persists, contact the technical
assistance department.
- C h e c k l o c k c o n n e c t i o n s
- Unsuitable lock
- Repeat the limit switch adjustment procedure.
- Try moving the maximum limits of both
the opening and closing limit switches.
- Caution: the last centimetre of the piston's stroke,
during either opening or closing, cannot be used.
THALIA P
29