DEVA Broadcast DB9000-RX Installation Manual
Professional ip audio decoder with stereo & rds encoder module
Hide thumbs
Also See for DB9000-RX:
- Maintenance and operation instruction manual (64 pages) ,
- Quick user manual (6 pages)
Related Manuals for DEVA Broadcast DB9000-RX
Summary of Contents for DEVA Broadcast DB9000-RX
-
Page 1: Installation Guide
INSTALLATION GUIDE DB9000-RX Professional IP Audio Decoder with Stereo & RDS Encoder Module Publish Date: 12-Oct-2015... - Page 2 In order to facilitate the assembling of DB9000RX with the Stereo and RDS Encoder module we have written these detailed instructions. The instructions will acquaint you with the assembly of the RDS encoder module. Please read them carefully before you start. We have illustrated with a photograph each step of the assembling process.
- Page 3 *** NOTE: Please note that the device must be connected to the electrical network during the assembly. Please observe the safety standards. Step 1: Place the device on a working table with static surface. The rear part of the device must be set against you (Picture 1 represents the proper position for the device).
- Page 4 *** NOTE: Please note that the device must be connected to the electrical network during the assembly. Please observe the safety standards. Step 2: Use a star blade screwdriver № PH2 to unbolt the bolts holding the cover of the device on its left and right side. Picture 2 and Picture 3 show the position of the bolts.
- Page 5 *** NOTE: Please note that the device must be connected to the electrical network during the assembly. Please observe the safety standards. Step 3: Use a star blade screwdriver № PH1 to unscrew bolts with numbers from 1 to 8 which hold the rear cover of the device. Picture 4 displays the position of the bolts.
- Page 6 *** NOTE: Please note that the device must be connected to the electrical network during the assembly. Please observe the safety standards. Step 4: The next step of the process is the removal of the plugs (circled in red on Picture This will ensure space for the cable terminals of the Stereo and RDS Encoder Module.
- Page 7 *** NOTE: Please note that the device must be connected to the electrical network during the assembly. Please observe the safety standards. Step 5: Use a star blade screwdriver № PH2 to unscrew the bolts holding the front panel of the device on its left and right side. Picture 6 and Picture 7 show the position of the bolts.
- Page 8 *** NOTE: Please note that the device must be connected to the electrical network during the assembly. Please observe the safety standards. Step 6: Use a star blade screwdriver № PH1 to gently unbolt the bolts holding the motherboard to the metal bottom of DB-9000RX. Picture 8 displays the position of the bolts.
- Page 9 *** NOTE: Please note that the device must be connected to the electrical network during the assembly. Please observe the safety standards. Step 7: Before we continue with the next step, please pay special attention to Picture Carefully place both motherboards one next to the other and fit together the plug and socket connectors.
- Page 10 *** NOTE: Please note that the device must be connected to the electrical network during the assembly. Please observe the safety standards. Step 8: Carefully place the connected motherboards into the device’s metal body. The picture below shows the correct position of the motherboards and the cable terminals.
- Page 11 *** NOTE: Please note that the device must be connected to the electrical network during the assembly. Please observe the safety standards. Step 9: Once the Stereo and RDS Encoder Module is added to DB-9000RX Professional IP Audio Decoder, the entire unit has to be reassembled following the steps listed above in a reverse order –...
- Page 12 Step 10: If the set-up procedure has been completed successfully, there is not a hardware problem, and the boards are communicating properly, upon establishing a connection with the WEB interface, the MPX function should be available (as depicted on the screenshot). If a problem during the process of installation has occurred, or the boards are not communicating properly, upon establishing a connection with the WEB interface, when MPX function is selected, the following message will appear...
- Page 13 In this case, following strictly the previously described procedure, remove the equipment’s lid (Steps 1 & 2) and make sure that the MPX board has been properly installed. *** NOTE: Please note that the device must be connected to the electrical network during the assembly/reassembly.