Related Manuals for J-Tech Digital JTECH-ENCH4
Summary of Contents for J-Tech Digital JTECH-ENCH4
-
Page 1: User Manual
Website: www.jtechdigital.com Toll Free: 1-888-610-2818[US] Email: Support@jtechdigital.com USER MANUAL J-Tech Digital ® IPTV H264 Encoder R oH S JTD-ID:220... -
Page 2: Table Of Contents
Table of Contents Features ........................3 Package Contents ......................3 Hardware Description ....................4 Typical Application ......................4 Environment Configuration ................... 5 5.1. Software ......................5 5.1.1. Change the IP Address of PC ................5 5.1.2. Login for configuration ..................6 5.1.3. -
Page 3: Features
Dear Customer Thank you for purchasing the JTECH-ENCH4. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. 1. FEATURES ➢ Supports H.264 encoding. ➢ Supports UDP, HTTP, RTSP, RTMP, ONVIF protocol. -
Page 4: Hardware Description
3. HARDWARE DESCRIPTION ① Power input port ② HDMI input ③ Reset button ④ LAN output ⑤ Indicator of power input ⑥ Indicator of LAN output ⑦ Indicator of HDMI input Note: . Reset to the factory default setting: press “Reset” for 10 seconds till all three indicators go out. -
Page 5: Environment Configuration
5. Connection Configuration 5.1 Software 5.1.1 Change the IP Address of PC Assign the PC (or laptop) an IP address. On a Windows PC: Press the +R on your keyboard →Enter “control netconnections” in the run box and press enter → Right click on your wired ethernet adapter →... -
Page 6: Check The Stream Address
5.1.3 Check the stream address As below, the stream address is in the red frame. 6. Encoder Setting 6.1 Encoder Setting Click “Encoder” setting → “Main stream” → Configure your settings → Click Apply... -
Page 7: Audio Setting
6.2 Audio setting Click “Encoder” → “Audio” → Configure your settings → Click “Apply” 6.3 Advanced Click “Encoder” → “Advanced” → Configure your settings → Click “Apply”. -
Page 8: Osd Setting
7. OSD Setting 7.1 Streaming OSD Setting Click “OSD” → “Network” → Configure your settings → Click “Apply” 7.2 LOGO uploading “LOGO upload” → Choose a bmp file that matches the requirements → Click “Apply” ※Note: The screenshots might have some difference with actual operation interface due to software upgrade, all the screenshots are for reference only. -
Page 9: System Setting
8. System 8.1 Network Click system → Network → Modify the network settings to match those of your network → Click apply. Note: Please change your DNS server to use Google’s DNS servers. (Provided in the picture below.) 8.2 Change password System →... -
Page 10: Reset
8.3 Reset System → Reset → Reset Note: This will set your device to the factory defaults. 8.4 Reboot System → Reboot → Reboot (please refresh the web page after 1 minute) -
Page 11: Application
9. Application 9.1 User Application Example 9.1.1 Web Video Preview Status → Main stream → Preview Note: For Internet Explorer, you can get preview window directly. For Chrome, you must install an extension called "Native HLS Playback" to get the preview window. -
Page 12: Vlc Play
9.1.2 VLC Play Connect a HDMI source to the HD encoder. Open VLC media player (Download link： http://www.videolan.org/)，Click “Media”, then click “Open Network Stream”. Enter the Stream URL from the page of “Main stream”, click “Play”. Note: Please make sure that the stream type you choose, is enabled in the encoder. -
Page 13: Multi Local User Application Multicast Way
VLC Example: 9.2 Multi Local User Application Multicast Way If more than one local user needs to stream the video, of the same HD encoder, at the same time. You may enable multicast IP, then reboot the HD encoder. After the reboot, copy the multicast IP address from the Status page, and paste the IP address into the VLC Player. -
Page 14: Local Surveillance System Application Nvr Conncetion
9.3 Local Surveillance System Application NVR Connection 1. Confirm if your NVR supports the H.264 codec. Since we’re using ONVIF, you will need to enable the "RTSP" function as pictured below. 2. If you need the NVR to recognize the audio of the HD Encoder, you will need to enable the Audio as below picture:... -
Page 15: Remote Multi User Application Rtmp Connection
Note: If you've enabled the ONVIF setting and still can't open the video, we suggest you download the ONVIF TEST tool. 9.4 Remote Multi User: RTMP Connection To stream over the web, to multiple locations, you may use RTMP. This encoder supports multiple platforms, including: YouTube Live, Facebook Live, DaCast, Red5, etc. - Page 16 “Server URL” and “Stream name/key” (separated by a forward slash). Full RTMP URL Example: rtmp://a.rtmp.youtube.com/live2/zc3e-yw22-bbdw-baeg 2.Enter the full RTMP URL into the “RTMP PUBLISH URL” setting of your J-Tech Digital Encoder; apply and reboot. Note: For best results, check that “TS muxer” is set to “Compatible with FFMPEG”...
-
Page 17: Warranty
MAINTENANCE Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner of benzine to clean. PRODUCT SERVICE 1) Damage requiring service: The unit should be serviced by qualified service personnel if: (a)The DC power supply cord or AC adaptor has been damaged; (b)Objects or liquids have gotten into the unit;...
Need help?
Do you have a question about the JTECH-ENCH4 and is the answer not in the manual?
Questions and answers