Braeburn 7320 Installer's Manual
Universal programmable smart wi-fi thermostat.
up to 3 heat / 2 cool heat pump
up to 2 heat / 2 cool conventional
with wireless humidity control
Hide thumbs
Also See for 7320:
- User manual (40 pages) ,
- Setup manual (10 pages) ,
- Installer's manual (17 pages)
Table of Contents
Advertisement
Quick Links
Installer Guide
Universal Programmable Smart Wi-Fi Thermostat
7320 Up to 3 Heat / 2 Cool Heat Pump
See Wi-Fi Setup Guide for Wi-Fi Setup Instructions
1 Specifications 2 Installation and Wiring 3 Quick Reference
4 Installer Settings 5 Wireless Remote Sensors 6 System Testing
Attention
To prevent damage to the thermostat, never use a sharp instrument
to press the touchscreen keys. Always press keys with your fingers.
Warning
Caution
This thermostat requires 24 Volt AC Power or 2 properly installed "AA" Alkaline
batteries for proper operation.
1 Specifications
This thermostat is compatible with:
Electrical and control specifications:
Terminations:
Up to 2 Heat / 2 Cool Conventional
with wireless Humidity Control*
.
TM
7320-100-01
Advertisement
Table of Contents
Related Manuals for Braeburn 7320
Summary of Contents for Braeburn 7320
- Page 1 Installer Guide Universal Programmable Smart Wi-Fi Thermostat 7320 Up to 3 Heat / 2 Cool Heat Pump Up to 2 Heat / 2 Cool Conventional with wireless Humidity Control* See Wi-Fi Setup Guide for Wi-Fi Setup Instructions 1 Specifications 2 Installation and Wiring 3 Quick Reference...
-
Page 2: Installation And Wiring
2 Installation and Wiring Warning Thermostat Location Install your new Braeburn thermostat in 4 basic steps: Install the Sub-Base: Drill 3/16” pilot holes in your desired location. Use supplied anchors for drywall or plaster. Installer Guide... - Page 3 Provide Power 24VAC Power Terminal (C) Batteries Installed as Shown Connect Your Wires Terminal Function Description Installer Guide...
- Page 4 Conventional Systems NOTE: The “System Type” option will be configured in the Installer Settings section. 2 HEAT / 2 COOL Single or Dual transformer Heat Only Set System Type to 22CONV Set System Type to 11CONV [note 2] [note 2] [note 4] [note 1] [note 4]...
- Page 5 NOTE: The “System Type” option will be configured in the Installer Settings section. 3 HEAT / 2 COOL – Including Auxiliary Heat 1 HEAT / 1 COOL - No Auxiliary Heat Set System Type to Set System Type to [note 2] [note 2] [note 1] [note 3]...
- Page 6 NOTE: Additional options are configured in the NOTES - Additional Wiring Options Installer Settings section. ® [note 1] [note 2] Attach Thermostat to Sub-Base W1/E W1/E INSTRUCTIONS /AUX1 /AUX1 AUX2 HUMID NOTE: This thermostat ships configured as a 1H/1C conventional thermostat.
-
Page 7: Quick Reference
3 Quick Reference INSTRUCTIONS HUMID Thermostat Display Room Temperature Lock Mode Indicator Set Temperature Service Indicators Humidity Indicator Time of Day Program Event Indicator Day of the Week System Status Indicator Hold Mode Indicator Low Battery Indicator Wi-Fi/Wireless Indicator Fan Indicator Thermostat Quick Reference Instructions SpeedBar... -
Page 8: Thermostat Touchpads
INSTRUCTIONS HUMID Thermostat TouchPads NOTE: Thermostat TouchPads are located on the left, right and bottom portions of the display screen. They are the “touch sensitive” segments used to adjust your thermostat. Depending on the equipment installed, all touch pads may not show. SYSTEM PROG ®... -
Page 9: Installer Settings
4 Installer Settings SYSTEM CONFIG ® DOWN NEXT BACK RETURN No. Installer Setting Factory Setting Comments Default Options Notes follow this table) (More information follows this table) COMM 7 PROG 7 PROG 52 PROG [note 1] NO PROG 12 HR 12 HR 24 HR F DEG... - Page 10 No. Installer Setting Factory Setting Comments Default Options Notes follow this table) (More information follows this table) AE AUX AE AUX AG AUX [note 4] oF CPOP oF CPOP on CPOP [notes 4, 6] AC oF MONR AC oF MONR AC on MONR [note 6] 5 CSCP...
- Page 11 NOTES - Installer Settings ® Detailed Explanation of Installer Settings (also see NOTES above): Profile Programming Mode [note 1] Clock Type Temperature Scale Auto Changeover NOTE: Also see “Auto Changeover Dead Band” in option 22. System Type NOTE: Changes made to this option will reset options 7 through 14 back to their default values dependant on the system type.
- Page 12 ® 20 Indoor Remote Sensor Control [note 8] NOTE: This option does not apply to the Braeburn outdoor sensor. When an outdoor sensor is connected (wired) or paired (wireless), the thermostat automatically recognizes it and no further configuration is necessary.
- Page 13 25 Economizer, Fresh Air or Output Control [note 11] Time Step / Override Cooling Call External Air or Output Control (A) Economizer Time of Disabled Mode Day Mode Occupied YES or NO Unoccupied Override YES or NO Time Step / Override Heating Call External Air Output (A) Economizer...
- Page 14 5 Wireless Remote Sensors NOTE: See the wireless remote sensor manual for complete installation and use instructions. Compatible Wireless Remote Sensors NOTE: No more than 4 wireless remote sensors can be connected. Pairing Wireless Remote Sensors CONFIG DAY/TIME NEXT CONNECT NEXT RETURN NOTE: Sensors that have already been paired will appear in the thermostat display first, with a solid...
-
Page 15: System Testing
Wireless Remote Sensor Communication Loss NOTE: To attempt to reconnect manually, press and hold the CONNECT button for 3 seconds. Wireless Remote Sensor Low Battery IDS1, IDS2, IDS3 IDS4 Table 2 NOTE: If Audible Tone is enabled in User Options (see User Manual), the thermostat will also sound a beep every 60 seconds when communication has been lost. -
Page 16: Limited Warranty
&H GLVSRVLWLI GRLW DFFHSWHU WRXWH LQWHUIpUHQFH \ FRPSULV OHV LQWHUIpUHQFHV TXL SHXYHQW FDXVHU XQ PDXYDLV IRQFWLRQQHPHQW GH O DSSDUHLO /D GLVWDQFH HQWUH O XWLOLVDWHXU HW GH SURGXLWV QH GHYUDLW SDV rWUH LQIpULHXUH j FP Limited Warranty YEAR ARRANTY Store this manual for future reference. 7320-100-01...