Table of Contents
Advertisement
Quick Links
Dialog User Level (continued)
Dialog
Value
Function/Description
item
Only models with analog output:
0 ... xxx
Scale the analog output - start value (e. g. 0 bar = 4 mA)
*
0 ... xxx
Scale the analog output - end value (e. g. 400 bar = 20 mA)
*
(output signal start value always corresponds to the display initial value, e. g. 0
bar = 4mA)
Maximum turn-down 4 : 1, i.e. at values below 25 % of the measuring range
the analog output is switched off
0 ... xxx
Display of peak value „Max" (xxxx: = max. 125 % f. s.)
Delete the maximum value memory
= no deletion
= delete value
Error display:
= no error
= exceeding pos. measuring range
= exceeding neg. measuring range
= sensor error
= error switching output 1
= error switching output 2
= data error (EEProm)
= program error
= calibration error
= error analog out
IMPORTANT
When changing units from psi to bar or bar to psi, the switching point values must be changed
accordingly.
* Flashing of the mean segment signals a negative setting value.
8
Operating Instructions
Dual pressure switch Switch 2000
Dual Temperature Switch TempSwitch 2000
1
Intended Applications .................................................................................................... 2
2
Safety Instructions ......................................................................................................... 2
3
Standards ........................................................................................................................ 3
4
Warranty/Guaranty ......................................................................................................... 3
5
Installation/Commissioning .......................................................................................... 3
6
Maintenance/Cleaning ................................................................................................... 4
7
Technical Data ................................................................................................................ 5
8
Operation......................................................................................................................... 6
9
Programming .................................................................................................................. 6
10
User Level Dialog Switch 2000/TempSwitch 2000 ...................................................... 7
Barksdale GmbH
Dorn-Assenheimer Straße 27
D-61203 Reichelsheim
Tel.:
+49 (6035) 949-0
Fax:
+49 (6035) 949-111 and 949-113
email:
info@barksdale.de
Internet: www.barksdale.de
Art. no.: 923-1440
Index O, 10.05.2011
Software-Version: V 2.1 and higher
Specifications are subject to changes
without notice!
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Barksdale TempSwitch 2000
Summary of Contents for Barksdale TempSwitch 2000
-
Page 1: Operating Instructions
Technical Data ........................ 5 = data error (EEProm) Operation......................... 6 Programming ........................6 = program error User Level Dialog Switch 2000/TempSwitch 2000 ............7 = calibration error = error analog out IMPORTANT Barksdale GmbH When changing units from psi to bar or bar to psi, the switching point values must be changed Dorn-Assenheimer Straße 27... - Page 2 Intended Applications Standards The dual pressure switch monitors system pressures and has up to two switching outputs and one The standards applied during development, manufacture and configuration are listed in the CE analog output. conformity and manufacturer's declaration. The dual temperature switch monitors media temperature into which the probe is immersed and has up to two switching outputs and one analog output.
- Page 3 IMPORTANT function", acknowledge inputs 12 (0.47) Change dialog items/functions, Only TempSwitch 2000 change numerical values When the rotatable display is adjusted, the switch has to be fixed with the threaded pin at the front side with a 3 Nm torque.
- Page 4 Dialog Value Function/Description making entries. After being switched on the Switch 2000 / TempSwitch 2000 runs through a self-test. item Operation via three plastic film keys is menu-driven. These keys must not be touched with hard objects! If an error is recognized during the self-test or during operation, this is signalled by the (yellow) flashing 0 ...
Need help?
Do you have a question about the TempSwitch 2000 and is the answer not in the manual?
Questions and answers