Specifi Cations - Sony CMT-DH7BT Operating Instructions Manual

On placement
 Do not place the system in an inclined
position or in locations that are extremely
hot, cold, dusty, dirty, or humid or lacking
adequate ventilation, or subject to vibration,
direct sunlight or a bright light.
 Be careful when placing the unit or speakers
on surfaces that have been specially treated
(for example, with wax, oil, polish) as
staining or discoloration of the surface may
result.
 If the system is brought directly from a cold
to a warm location or is placed in a very
damp room, moisture may condense on the
lens inside the DVD player, and cause the
system to malfunction. In this situation,
remove the disc, and leave the system turned
on for about an hour until the moisture
evaporates.
On heat buildup
 Heat buildup on the unit during operation is
normal and is not cause for alarm.
 Do not touch the cabinet if it has been used
continuously at a high volume because the
cabinet may have become hot.
 Do not obstruct the ventilation holes.
On the speaker system
Th is speaker system is not magnetically
shielded, and the picture on nearby TV
sets may become magnetically distorted. In
this situation, turn off the TV, wait 15 to 30
minutes, and turn it back on. If there is no
improvement, move the speakers far away from
the TV.
IMPORTANT NOTICE
Caution: If you leave a still video image
or on-screen display image displayed on
your TV for an extended period of time via
this system, you risk permanent damage
to your TV screen. Projection TVs are
especially susceptible to this.
Cleaning the cabinet
Clean this system with a soft cloth slightly
moistened with a mild detergent solution.
Do not use any type of abrasive pad, scouring
powder, or solvent, such as thinner, benzine,
or alcohol.
GB
76
CMT-DH7BT.GB.3-097-195-11(1)

Specifi cations

Main unit (HCD-DH7BT/Compact Disc
Receiver)
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 6 ohm loads, both channels driven,
from 120 – 10,000 Hz; rated 50 watts per
channel minimum RMS power, with no
more than 10% total harmonic distortion
from 250 milliwatts to rated output.
Amplifi er section
DIN power output (rated)
40 W + 40 W (6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
Front speaker:
50 W + 50 W (6 ohms at 1 kHz, 10%
THD)
Inputs:
AUDIO IN (stereo mini jack):
Voltage 620 mV, impedance
47 kilohms
Outputs:
DIGITAL OUT (square optical connector
jack):
Wavelength 660 nm
VIDEO OUT (phono jack):
Max. output level 1 Vp-p, unbalanced,
Sync. negative load impedance
75 ohms
COMPONENT VIDEO OUT:
Y: 1 Vp-p, 75 ohms
Pb/Cb: 0.7 Vp-p, 75 ohms
Pr/Cr: 0.7 Vp-p, 75 ohms
S VIDEO OUT (4-pin/mini-DIN jack):
Y: 1 Vp-p, unbalanced, Sync. negative
C: 0.286 Vp-p, load impedance
75 ohms
PHONES (stereo mini jack):
accepts headphones of 8 ohms or
more
Blueto
Comm
B
Outpu
B
Maxim
L
Freque
2
G
Modul
F
Compa
A
P
A
C
Suppor
R
T
1
2
Disc pl
System
C
v
Laser:
Laser D
E
L
*
Semico
(
Freque
D
(
C
Video
N
CMT-