Do you have a question about the Pacesetter 13 and is the answer not in the manual?
Questions and answers
Richard Cole
April 29, 2025
Need to assemble machine handle and power switch
1 comments:
Mr. Anderson
May 15, 2025
To assemble the handle and power switch on the Nilfisk Pacesetter 13:
1. Unwrap the power cord and plug it into a properly grounded outlet. 2. Pull up on the Handle Release Compression Lever. 3. Move the Operator Handle downward until your arms are almost straight. 4. Push down on the Handle Release Compression Lever to lock the handle in place. 5. Lift the Operator Handle until the brush or pad is flat against the floor.
The power switch is integrated with the handle and includes a safety activation switch.
Products in such environments. The Manufacturer disclaims any responsibility to advise purchasers of any specifi c requirements that may be applicable to the use of the Products in such environments. revised 3/13 2 - FORM NO. 70139A - Pacesetter 13, 17, 20, 17HD, 20HD, 20TS, 20SD...
Extension cords connected to this machine should be 12 gauge, three-wire cords with three-prong plugs and outlets. DO NOT use extension cords more than 50 feet (15 m) long. GROUNDED OUTLET GROUNDING PIN FIGURE 4 revised 3/13 FORM NO. 70139A - Pacesetter 13, 17, 20, 17HD, 20HD, 20TS, 20SD - 3...
Store the machine in a clean, dry place with the Operator Handle (6) WARNING! locked in the upright position. This machine contains moving parts. To reduce the risk of injury, always unplug the power cord before servicing. FORM NO. 70139A - Pacesetter 13, 17, 20, 17HD, 20HD, 20TS, 20SD - 5...
Page 8
El Fabricante niega toda responsabilidad de informar a los compradores sobre requisitos específi cos que pueden regir el uso de los Productos en tales entornos. revised 3/13 8 - FORM NO. 70139A - Pacesetter 13, 17, 20, 17HD, 20HD, 20TS, 20SD...
Los cables de extensión conectados a esta máquina deben ser de calibre 12, de tres hilos, con enchufes y tomacorrientes de tres puntas. NO USE cables de extensión que superen 50 pies (15 m) de longitud. Toma corriente con polo de tierra Terminal de tierra FIGURA 4 revised 3/13 FORM NO. 70139A - Pacesetter 13, 17, 20, 17HD, 20HD, 20TS, 20SD - 9...
Esta máquina contiene piezas en movimiento. Para reducir el riesdo de lesiones, siempre desconecte el cable de energía antes de realizar el mantenimiento de la máquina. FORM NO. 70139A - Pacesetter 13, 17, 20, 17HD, 20HD, 20TS, 20SD - 11...
Page 12
Acero tubular Acero tubular Acero tubular Acero tubular Base Alumminio fundido a presión Alumminio fundido a presión Alumminio fundido a presión Alumminio fundido a presión revised 3/13 12 - FORM NO. 70139A - Pacesetter 13, 17, 20, 17HD, 20HD, 20TS, 20SD...
Page 13
91 lbs (41.4 kg) 95 lbs (43.2 kg) Construcción: Tubo de la manija Acero tubular Acero tubular Base Alumminio fundido a presión Alumminio fundido a presión FORM NO. 70139A - Pacesetter 13, 17, 20, 17HD, 20HD, 20TS, 20SD - 13...
Le Fabricant rejette toute responsabilité d’informer les acheteurs concernant des exigences spécifi ques qui peuvent s’appliquer à l’utilisation des Produits dans de tels environnements. revised 3/13 14 - FORM NO. 70139A - Pacesetter 13, 17, 20, 17HD, 20HD, 20TS, 20SD...
Page 15
N’utilisez PAS des cordons prolongateurs de plus de 50 pieds (15 m). Prise de courant avec mise à la terre Broche de mise à la terre FIGURE 4 revised 3/13 FORM NO. 70139A - Pacesetter 13, 17, 20, 17HD, 20HD, 20TS, 20SD - 15...
(6) verrouillée en position verticale. Cette machine contient des pièces mobiles. A n de réduire le risque de blessures, déconnectez toujours le câble d’alimentation avant de procéder à l’entretien. FORM NO. 70139A - Pacesetter 13, 17, 20, 17HD, 20HD, 20TS, 20SD - 17...
Need help?
Do you have a question about the Pacesetter 13 and is the answer not in the manual?
Questions and answers
Need to assemble machine handle and power switch
To assemble the handle and power switch on the Nilfisk Pacesetter 13:
1. Unwrap the power cord and plug it into a properly grounded outlet.
2. Pull up on the Handle Release Compression Lever.
3. Move the Operator Handle downward until your arms are almost straight.
4. Push down on the Handle Release Compression Lever to lock the handle in place.
5. Lift the Operator Handle until the brush or pad is flat against the floor.
The power switch is integrated with the handle and includes a safety activation switch.
This answer is automatically generated
How to replace power switch and assemble handle