Related Manuals for Ripmax Wots Wot FOAM-E
Summary of Contents for Ripmax Wots Wot FOAM-E
- Page 2 Wots Wot FOAM-E Instructions / Wots Wot FOAM-E Anleitung Chris Foss Chris Foss The Designer / Der Designer fascination flight captured Chris's imagination early on in his life when he started building, from kits and plans, simple free flight gliders and rubber powered models.
- Page 3 Introduction / Einführung Congratulations on your purchase of the Wots Wot Foam-E! This is not just any foam model... it's a very clever Wots Wot that can be flight ready in under 30 minutes! The beautiful EPO mouldings hide an innovative internal structure that adds strength where needed and locks all the components together.
- Page 4 Wots Wot FOAM-E Instructions / Wots Wot FOAM-E Anleitung Stage 1 / Schritt 1 Connect the elevator pushrod by slotting the 90 degree bend through the elevator horn. Then place the plastic connector over the wire and clip into place to secure.
- Page 5 Wots Wot FOAM-E Instructions / Wots Wot FOAM-E Anleitung Stage 6 / Schritt 6 Secure the tailwheel bracket with machine screw 'B'. Sichern Sie die Spornrad Halterung mit der Schraube "B". Stage 7 / Schritt 7 Secure the wire into the rudder by clamping it into position using the rudder horn.
- Page 6 Wots Wot FOAM-E Instructions / Wots Wot FOAM-E Anleitung Stage 11 / Schritt 11 Now install the undercarriage using 'I' machine screws and 'K' washers. Nun befestigen Sie das Fahrwerk mit den Schrauben "I" und den Unterlegscheiben "K". Stage 12 / Schritt 12 Now is the best time to apply the decals.
- Page 7 Wots Wot FOAM-E Instructions / Wots Wot FOAM-E Anleitung Stage 13 / Schritt 13 Connect the aileron servo lead to the receiver and bolt the bottom wing into position using the 'F' machine screw. Verbinden Sie das Querruder Servokabel mit dem Empfänger und schrauben die Unterseite des Flügels mit...
-
Page 8: Control Throws
Wots Wot FOAM-E Instructions / Wots Wot FOAM-E Anleitung Stage 18 / Schritt 18 Remove the two screws securing the spinner and use a 10mm driver to clamp the propeller to the motor shaft. Once secure reinstall the spinner but be careful not to over tighten the screws. - Page 9 Pre-Flight Checks / Vorflug Checks While the Wots Wot Foam-E is not a trainer, it does make an excellent first aileron model with reduced control throws. In this case, we recommend that your completed model is checked over and test flown by a competent pilot first. Subsequent flights should also be supervised, and assisted where necessary, by an experienced pilot.
- Page 10 Wot 4 with the precision and responsiveness of the AcroWot. We are pleased to say the Wots Wot Foam-E has all of these great attributes with the added bonus of a light wing loading.
- Page 11 Wots Wot FOAM-E Instructions / Wots Wot FOAM-E Anleitung...
- Page 12 Adresse, oder besuchen Sie unsere Webseite unter www.ripmax.com. Spare parts are available for the Wots Wot Foam-E from all Ripmax stocked model shops. In case of any difficulty, any product queries, or to locate your local Ripmax stockist, please write to the address below or visit www.ripmax.com Made in China Distributed to your local model shop by Ripmax Ltd., 241 Green Street, Enfield, EN3 7SJ.