DuraLabel Bronco User Manual
Hide thumbs
Also See for Bronco:
- User manual (24 pages) ,
- Quick start manual (8 pages) ,
- User manual (20 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for DuraLabel Bronco
Summary of Contents for DuraLabel Bronco
- Page 1 USER GUIDE 800.788.5572 GraphicProducts.com...
- Page 2 Graphic Products , DuraLabel , PathFinder , Toro and Lobo are Registered Trademarks of Graphic Products, Inc. ® ® ® ® ® © 2015 Graphic Products, Inc.
-
Page 3: Before You Begin
Before You Begin Safety Warnings Before connecting Bronco to a power outlet, check the voltage of the power source, and ensure that the power switch on the printer is in the OFF position. Only use the included power supply with the Bronco (rated for 24V/2.5A output, model WDS060240). -
Page 4: Table Of Contents
Loading Supplies 1.2.1 Loading Ribbon 1.2.2 Loading Label Stock Initial Setup 1.3.1 Physical Connections 1.3.2 Installing Driver Software 2. Using Your Bronco Printing and Pausing Driver Settings 2.2.1 Size and Orientation 2.2.2 Settings for Pre-Printed or Die-Cut Material 2.2.3 Cutting 2.2.4 Darkness... -
Page 5: Getting Started
1. Getting Started Know Your Bronco 1.1.1 EXTERIOR Pause/Feed Button and Indicator Light Lid Release Tabs Cutter Module 1.1.2 CONNECTION PANEL Power Switch Power Supply Connection USB Connection 1.1 Know Your Bronco | GraphicProducts.com | 800.788.5572... -
Page 6: Interior - Print Head Carriage Locked
GETTING STARTED 1.1.3 INTERIOR – PRINT HEAD CARRIAGE LOCKED Ribbon Take-Up Holders Carriage Release Tabs Print Head Carriage 1.1.4 INTERIOR – PRINT HEAD CARRIAGE RELEASED Print Head Ribbon Supply Holders Adjustable Supply Guides | 1.1 Know Your Bronco GraphicProducts.com | 800.788.5572... -
Page 7: Loading Supplies
GETTING STARTED Loading Supplies To load your Bronco with supplies, turn the system off using the power switch at the back, near the power cord. Then, press inward at the textured areas on both sides of the system, and raise the hinged cover. The cover will rest at the fully-opened position, requiring about 12 inches of vertical clearance. -
Page 8: Loading Label Stock
Fresh label stock comes in a roll with plastic end caps on each side. The material typically has a glossy print surface on one side, and a disposable paper backing on the other side. When printing, Bronco will feed some of the label stock from its roll and cut off the printed label. -
Page 9: Using Your Bronco
Many programs have their own settings for a document’s page size; for instance, Microsoft Word is typically set to use 8.5”x11” pages, in a Portrait orientation. Your Bronco has similar settings, and these need to match your label design for the label to be printed correctly. -
Page 10: Settings For Pre-Printed Or Die-Cut Material
Your Bronco’s driver settings for these types of material are located on the Stock tab of the Printing Preferences window. The Media Type can be set to one of the following: • Continuous: an uninterrupted, continuous roll of label stock (the most common... -
Page 11: Darkness
• If you use Windows 8 or Windows 8.1, go through your computer’s Charms Bar to the Control Panel, and open the “Devices and Printers” window. Find the entry in this window for your DuraLabel Bronco, right-click on it, and choose Printing Preferences. These settings will be saved for future use. -
Page 12: Warranty And Compliance Statements
Such remedy shall be the purchaser’s sole and exclusive remedy for any breach of warranty. General maintenance and cleaning of the DuraLabel printer is the purchaser’s responsibility and is not covered by the warranty. Expendable items or parts such as label supply and ribbon are not covered by this warranty. -
Page 13: Fcc Compliance Statement For Users In The United States
WARRANTY AND COMPLIANCE STATEMENTS FCC Compliance Statement for Users in the United States This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 14: Contact Us
User Guide, please let us know. Graphic Products proudly offers free support to all of our customers. Call us at: 800.788.5572 (U.S.A. and Canada only) 1.503.644.5572 (International) Visit our website at GraphicProducts.com Email us at info@graphicproducts.com | 4. Contact Us DuraLabel.com | 800.788.5572... - Page 15 THIS PAGE IS INTENTIONALLY LEFT BLANK...
- Page 16 800.788.5572 | DuraLabel.com © 2015 Graphic Products, Inc. All Rights Reserved 02/11/15...
Need help?
Do you have a question about the Bronco and is the answer not in the manual?
Questions and answers