Falcon G3830 Installation And Servicing Instructions

Falcon G3830 Installation And Servicing Instructions

Advertisement

Quick Links

G3830, G3860, G3865 Fryers
INSTALLATION and
SERVICING INSTRUCTIONS
This appliance must be installed and serviced by a competent person as stipulated by the
Gas Safety (Installation & Use) Regulations.
IMPORTANT
The installer must ensure that the installation of the appliance is in conformity with these instructions
and National Regulations in force at the time of installation. Particular attention MUST be paid to:
Gas Safety (Installation & Use) Regulations
Health And Safety At Work etc. Act
Local and National Building Regulations
Fire Precautions Act
The appliance has been CE-marked on the basis of compliance with the Gas Appliance Directive for
the Countries, Gas Types and Pressures as stated on the data plate.
WARNING
TO PREVENT SHOCKS, ALL APPLIANCES WHETHER GAS OR ELECTRIC,
:
MUST BE EARTHED.
On completion of the installation, these instructions should be left with the Engineer-in-Charge for
reference during servicing. Further to this, The Users Instructions should be handed over to the User,
having had a demonstration of the operation and cleaning of the Appliance.
IT IS MOST IMPORTANT THAT THESE INSTRUCTIONS BE CONSULTED BEFORE INSTALLING
AND COMMISSIONING THIS APPLIANCE. FAILURE TO COMPLY WITH THE SPECIFIED
PROCEDURES MAY RESULT IN DAMAGE OR THE NEED FOR A SERVICE CALL.
PREVENTATIVE MAINTENANCE CONTRACT
In order to obtain maximum performance from this unit we would recommend that a maintenance
contract be arranged with SERVICELINE. Visits may then be made at agreed intervals to carry out
adjustments and repairs. A quotation will be given upon request to the contact numbers below.
WEEE Directive Registration No. WEE/DC0059TT/PRO
At end of unit life, dispose of appliance and any replacement
parts in a safe manner, via a licenced waste handler.
Units are designed to be dismantled easily and recycling of all
material is encouraged whenever practicable.
Falcon Foodservice Equipment
HEAD OFFICE AND WORKS
Wallace View, Hillfoots Road, Stirling. FK9 5PY. Scotland.
SERVICELINE CONTACT
Phone: 01438 363 000
Fax: 01438 369 900
Detailed recommendations are contained in
Institute of Gas Engineers published documents:
IGE/UP1, IGE/UP/2
BS6173 and BS5440
T100760 Ref.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the G3830 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Falcon G3830

  • Page 1 G3830, G3860, G3865 Fryers INSTALLATION and SERVICING INSTRUCTIONS This appliance must be installed and serviced by a competent person as stipulated by the Gas Safety (Installation & Use) Regulations. IMPORTANT The installer must ensure that the installation of the appliance is in conformity with these instructions and National Regulations in force at the time of installation.
  • Page 2: Important Information

    IMPORTANT INFORMATION Warranty Policy Shortlist Warranty does not cover :- • Correcting faults caused by incorrect installation of a product. • Where an engineer cannot gain access to a site or a product. • Repeat commission visits. • Replacement of any parts where damage has been caused by misuse. •...
  • Page 3 G3830 - Rp½ (½" BSP) If the floor is constructed of combustible material, G3860 - Rp¾ (¾" BSP) then local fire requirements should be checked to ensure G3865 - 2 x Rp½...
  • Page 4 SECTION 2 - 1.8.1 Natural Gas ASSEMBLY and COMMISSIONING Model Pilot Burner Main Burner 2.1 ASSEMBLY G3830 Fryer NG No. 18 Ø2.38mm The unit is packed as a complete assembly, except the G3860 Fryer NG No. 18 Ø3.2mm flue. To fit this, slide flue over upstand on hob rear and G3865 Fryer NG No.
  • Page 5 2.7 INSTRUCTION TO USER 3.2 BURNERS After installing and commissioning the fryer, hand User Burners should be cleaned periodically to maintain Instructions to operator or purchaser. Ensure details to maximum performance and are best cleaned with a wire light, turn off, use and clean are properly understood. brush.
  • Page 6 3.5 PIEZO IGNITER/SPARK ELECTRODE 3.6.3 Checking the User Thermostat Calibration The igniter is a piezo spark type. The electrode is Using a reliable thermometer immersed 25mm below oil mounted upon pilot burner bracket and switch is adjacent surface at pan centre. Measure oil temperature when a to MFC.
  • Page 7 SECTION 4 - SPARES When ordering spare parts, always quote unit type and serial number. This information will be found on data badge attached to base plate.

This manual is also suitable for:

G3860G3865

Table of Contents