Download Table of Contents Print this page
Epson L365 Service Manual

Epson L365 Service Manual

Color inkjet printer
Hide thumbs Also See for L365:

Advertisement

SERVICE MANUAL
Color Inkjet Printer
L365/L366, L360/L362/L363
L310/L312/L313,L220/L222, L130/L132
CONFIDENTIAL
SEMF14-013

Advertisement

Table of Contents
loading

Summary of Contents for Epson L365

  • Page 1 SERVICE MANUAL Color Inkjet Printer L365/L366, L360/L362/L363 L310/L312/L313,L220/L222, L130/L132 CONFIDENTIAL SEMF14-013...
  • Page 2 SEIKO EPSON would greatly appreciate being informed of them. The contents of this manual are subject to change without notice. The above not withstanding SEIKO EPSON CORPORATION can assume no responsibility for any errors in this manual or the consequences thereof.
  • Page 3: Safety Precautions

    Strictly observe the following cautions. Failure to comply may lead to personal injury or damage of the product. 1. Repairs on Epson product should be performed only by an Epson certified repair technician. 2. No work should be performed on this product by persons unfamiliar with basic safety knowledge required for electrician.
  • Page 4 7. In order to protect sensitive microprocessors and circuitry, use static discharge equipment, such as anti-static wrist straps, when accessing internal components. 8. Do not tilt this product immediately after initial ink charge, especially after performing the ink charge several times.
  • Page 5: Chapter 1 Troubleshooting

    About This Manual This manual, consists of the following chapters, is intended for repair service personnel and includes information necessary for properly performing maintenance and servicing the product. CHAPTER 1. TROUBLESHOOTING Describes the step-by-step procedures for the troubleshooting. CHAPTER 2. DISASSEMBLY / REASSEMBLY Describes the disassembly/reassembly procedures for main parts/units of the product, and provides the standard operation time for servicing the product.
  • Page 6 Revision Status Revision Date of Issue Description January 9, 2012 First Release Confidential...
  • Page 7: Table Of Contents

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Contents Chapter 1 Troubleshooting 1.1 Troubleshooting................................. 9 1.1.1 Troubleshooting Workflow ..........................9 1.2 Power-On Sequence ..............................11 1.3 Fatal Error Code List............................... 13 1.3.1 Printer Fatal Error Code ..........................13 Chapter 2 Disassembly/Reassembly 2.1 Overview ................................. 17 2.1.1 Tools ................................
  • Page 8 CHAPTER 1 TROUBLESHOOTING Confidential...
  • Page 9: Troubleshooting

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 1.1 Troubleshooting This section describes the troubleshooting workflow and fatal error information. In this chapter, the product names are called as follows: L365/L366 Series:L365/L366 L360/L362 Series:L360,L363/L362 L310/L312 Series:L310,L313/L312 L220/L222 Series:L220/L222 L130/L132 Series:L130/L132 1.1.1 Troubleshooting Workflow The following page describes the troubleshooting workflow. Follow the flow when troubleshooting problems.
  • Page 10 This error may occur in the • Contamination of Scanner Glass Unit. parts come-off / parts manual duplex printing if the • Contamination of Printhead • Recommendation of EPSON • Contamination of Document Pad cover media 3 Perform paper eject operation transformation in paper inverted sheet printed on the first •...
  • Page 11: Power-On Sequence

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 1.2 Power-On Sequence This section describes the power-on sequences in two conditions. The preconditions are as follows. Condition 1: Normal power-on sequence (See Table 1-1.) Turning on the printer after turning it off without an error.
  • Page 12 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Condition 2: Power-on sequence after recovering from a paper jam error (See Table 1-2.) Turning on the printer after turning it off with a paper jam fatal error. There still remains paper on the paper path out of the detecting area of the PE Sensor.
  • Page 13: Fatal Error Code List

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 1.3 Fatal Error Code List This section describes how to check the fatal error code, description, and the possible causes. 1.3.1 Printer Fatal Error Code This section describes the fatal error code and the possible cause for this product.
  • Page 14 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Error Error type Error name Possible cause code 0x9A Circuit error (include blowout of a fuse) • Main Board failure 0x9B Transistor temperature error 0x9C X-Hot detect error (pre printing) • Printhead failure 0x9D X-Hot detect error (after flushing) •...
  • Page 15 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Error Error type Error name Possible cause code • PF Encoder failure (contaminated/detached scale, Encoder Board failure) 0xF2 PF PID excess speed error • Motor driver failure (Main Board failure) • Slipping gears have occurred around the PF Motor gears.
  • Page 16: Chapter 2 Disassembly/Reassembly

    CHAPTER 2 DISASSEMBLY/REASSEMBLY Confidential...
  • Page 17: Overview

    Flathead Precision screwdriver #1 Tweezers Longnose pliers Acetate tape 1003963 Note 1: Some of the tools listed above are commercially available. 2: EPSON provides the tools listed with EPSON part code. 2.1.2 Jigs Name Quantity EPSON Part Code Spring hook jig* Can be made with a commercial item See "...
  • Page 18: Locations Of The Parts/Units

    Frame Base Assy (p35) Housing Left (p33) (L365/L366,L360/L362,L220/L222 Series only) Panel Unit Scanner Unit (p33) (L365/L366,L360/L362,L220/L222 Series only) • L365/L366 Series (p 35) Scanner Housing Upper (p37) Scanner Carriage Unit Panel Board Assy (p38) Panel Buttons (p38) (p37) Scanner Housing Lower (p37)
  • Page 19 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Printer mechanism Name Name CR Driven Pulley Assy (p35) CR Unit (p39) CR Scale (p35) PF Roller Unit (p39) CR Timing Belt (p39) Star Wheel Holder Assy (p37) Printhead (p33) Paper Guide Upper Assy (p39) CR Encoder Sensor (p39)
  • Page 20 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Name Name Wireless LAN Module (p33) (L365/L366 Series only) PF Scale (p36) EJ Roller (p37) PF Encoder Sensor (p36) PF Motor Assy (p39) EJ Roller Gear (p33) PF Timing Belt (p36) Figure 2-5. Printer Mechanism: Left...
  • Page 21 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Ink Supply Tank Assy Name Name Cover Joint (p36) Guide Tube Tank (p36) Top Cover (p36) Ink Supply Tank Ink Supply Tank (Cyan) (p36)/Ink Supply Tank Right Cover (p36) (Magenta) (p36)/Ink Supply Tank (Yellow) (p36)/Ink Ink Supply Tank Tube Assy (p36)
  • Page 22: Standard Operation Time For Servicing The Product

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 2.1.4 Standard Operation Time for Servicing the Product The following are the standard operation time for servicing the product. This standard operation time was determined with the MTTR result measured using the prototype of L360/L362 Series which have the most functions.
  • Page 23 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Table 2-1. Standard Operation Time Time (mm:ss) Parts/Unit Adjustment/ Replacement Total inspection Cap Lever 3:32 3:32 Panel Unit 4:21 4:21 Panel Housing Lower Assy 5:02 5:02 Panel Board Assy 5:21 5:21 Panel Bottons 5:37 5:37 Panel Housing Upper Assy...
  • Page 24 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Table 2-1. Standard Operation Time Time (mm:ss) Parts/Unit Adjustment/ Replacement Total inspection Ink Supply Tank (Cyan) 4:11 4:11 Ink Supply Tank (Black) 4:11 4:11 Ink Supply Tank Tube Assy 3:30 3:30 Tube Guide Sheet Sub 0:30...
  • Page 25: Checks And Precautions Before Disassembling

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 2.1.5 Checks and Precautions before Disassembling 2.1.5.1 Factors which Affect the Print Quality HOW TO PLACE THE INK TANK ASSY WHEN DISASSEMBLING/REASSEMBLING Do not place the Ink Supply Tank Assy with Ventilation Hole side down. Otherwise, ink in the Ink Supply Tank Assy may reach and cover the ventilation Hole, and the ink in the Ink Supply Tank Assy may leak.
  • Page 26: Factors Which Affect The Safety Of Service Personnel Such As Ink Leakage During Operation

    2.1.5.2 Factors which Affect the Safety of Service Personnel such as Ink Leakage during Operation Ink may spill when removing the following parts from L365/L366,L360/L362,L310/L312,L220/L222,L130/ L132 Series. This section describes the parts that may cause ink spill and the means to minimize the ink spill when removing the parts.
  • Page 27 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A MEANS DO TO MINIMIZE THE INK SPILL Even observing the points described in this section, ink may spill in the following situations. Therefore, be careful not to contaminate the inside of the printer or its surroundings by preparing the container to receive the leaked ink, or the like.
  • Page 28 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A DISCHRGING INK FROM THE INK SUPPLY TANK Discharging ink is recommended only when disconnecting the Ink Supply Tank Tube Assy from the Ink Supply Tank. Before performing the above disconnection, discharge ink from the Ink Supply Tank as follows.
  • Page 29 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Discharging procedure 1. Release the Ink Supply Tank Assy.(Refer to Cotton swab (x 4) (p.28)) 2. Place the Ink Supply Tank Assy on a place where its bottom is higher than the top of the Printhead.
  • Page 30 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A It is recommended that the ink in the Ink Supply Tank should be discharged completely before proceeding to disassembling/reassembling. After all the reassembling work is complete, the discharged ink of each color should be refilled back to the Ink Supply Tank before performing the adjustment. Confirm the colors indicated on the film of the Ink Supply Tank so as not to mistake them, and make sure to refill each ink back to the correct tank from the corresponding ink supply hole.
  • Page 31: Disassembly/Reassembly Procedures

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 2.2 Disassembly/Reassembly Procedures This section describes procedures for disassembling the parts/units in a flowchart format. For some parts/units, detailed procedures or precautions are provided (accordingly indicated by icons and cell's color). Refer to the explanations in the example chart below and perform an appropriate disassembling and assembling procedure.
  • Page 32: Disassembly Flowchart

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 2.2.1 Disassembly Flowchart L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series described in this manual have differences in their structure because the same printer mechanism is used for some of them and the composition of housings or functions differs. The functions and differences according to the models are as follows.
  • Page 33 C.B.S-TITE SCREW 3x6 F/ZN-3C 0.5 kgf·cm Common parts/unit ± C.B.S-TITE SCREW 3x6 F/ZN-3C 1 kgf·cm ± C.B.S-TITE SCREW 3x8 F/ZN-3C 1 kgf·cm L365/L366 Series specific parts/ ± unit C.P SCREW 3x4 F/ZN-3C 1 kgf·cm ± C.P.F.B-TITE SCREW 2x8 F/ZN-3C 1 kgf·cm L365/L366,L360/L362,L220/ ±...
  • Page 34 C.P.F.B-TITE SCREW 2x8 F/ZN-3C 1 kgf·cm Common parts/unit ± C.P.S-TITE (P2) SCREW 3x6 F/ZN-3C 1 kgf·cm ± C.B.P-TITE SCREW 2.5x8 F/ZN-3C 0.5 kgf·cm L365/L366 Series specific parts/ ± C.P SCREW 2.6x3 F/ZN-3C 0.5 kgf·cm unit ± C.B.S-TITE SCREW 3x4 F/ZN-3C 0.5 kgf·cm L365/L366,L360/L362,L220/ ±...
  • Page 35 1 kgf·cm ± Common parts/unit C.P.S-TITE (P2) SCREW 3x6 F/ZN-3C 1 kgf·cm ± C.B.P-TITE SCREW 2.5x8 F/ZN-3C 0.5 kgf·cm L365/L366 Series specific parts/ ± unit C.P SCREW 2.6x3 F/ZN-3C 0.5 kgf·cm ± C.B.S-TITE SCREW 3x4 F/ZN-3C 0.5 kgf·cm When the CR Unit or the Head FFC is removed from the Main Frame Assy, remove the L365/L366,L360/L362,L220/ ±...
  • Page 36 C.P.F.B-TITE SCREW 2x8 F/ZN-3C 1 kgf·cm ± Common parts/unit C.P.S-TITE (P2) SCREW 3x6 F/ZN-3C 1 kgf·cm ± C.B.P-TITE SCREW 2.5x8 F/ZN-3C 0.5 kgf·cm L365/L366 Series specific parts/ ± C.P SCREW 2.6x3 F/ZN-3C 0.5 kgf·cm unit ± C.B.S-TITE SCREW 3x4 F/ZN-3C 0.5 kgf·cm L365/L366,L360/L362,L220/ ±...
  • Page 37 (p 48) Guide 1st (p37) Cap Assy Ink Supply Tube Common parts/unit Guide 2nd (p37) (p 33) Star Wheel Holder Assy L365/L366 Series specific parts/ (p37) unit L365/L366,L360/L362,L220/ Star Wheel (p 44) Porous Pad for Scanner FFC Scanner Housing L222 Series specific parts/unit...
  • Page 38 C.P.F.B-TITE SCREW 2x8 F/ZN-3C 1 kgf·cm ± Common parts/unit C.P.S-TITE (P2) SCREW 3x6 F/ZN-3C 1 kgf·cm ± C.B.P-TITE SCREW 2.5x8 F/ZN-3C 0.5 kgf·cm L365/L366 Series specific parts/ ± C.P SCREW 2.6x3 F/ZN-3C 0.5 kgf·cm unit ± C.B.S-TITE SCREW 3x4 F/ZN-3C 0.5 kgf·cm L365/L366,L360/L362,L220/ ±...
  • Page 39 Common parts/unit C.P.S-TITE (P2) SCREW 3x6 F/ZN-3C 1 kgf·cm ± (p 52) (p 53) C.B.P-TITE SCREW 2.5x8 F/ZN-3C 0.5 kgf·cm L365/L366 Series specific parts/ ± C.P SCREW 2.6x3 F/ZN-3C 0.5 kgf·cm unit ± C.B.S-TITE SCREW 3x4 F/ZN-3C 0.5 kgf·cm Frame Base L365/L366,L360/L362,L220/ ±...
  • Page 40: Disassembly Flowchart (Printhead/Main Board)

    (p 53) Scanner FFC (CN11) Adapter Cover Hopper Housing Front Ferrite core FFC/Cable* 11 Common parts/unit Adapter L365/L366 Series specific parts/ Scanner Unit Main Board unit (p 53) L365/L366,L360/L362,L220/ L222 Series specific parts/unit (p 48) FFC/Cable* 9 Ink Supply Tube Assy...
  • Page 41: Detailed Disassembly/Reassembly Procedure For Each Part/Unit

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 2.3 Detailed Disassembly/Reassembly Procedure for each Part/Unit Document Mat (L365/L366,L360/L362,L220/L222 Series) Scanner Housing Upper (L365/L366,L360/L362,L220/L222 Series) Housing Rear (L365/L366,L360/L362,L220/L222 Series) Document Cover Step 2 Scanner Housing Upper Section B Document Mat Section C Step 3-4 Step 1...
  • Page 42 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Panel Unit (L365/L366 Series) Panel Housing Lower Assy (L365/L366 Series) Frame Base (left) Frame Base (right) Back Inside Panel Unit Panel Housing Lower Assy Panel Unit Rail section Rail section Panel Unit Panel Stand Panel Housing...
  • Page 43 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Main Board Wireless LAN Module (L365/L366 Series) LD Roller Assy (1) Rear of printer Position of MAC Address Label Wireless LAN Module Cable (L365/L366 Series only) Change Lever MAC Address Label Shield Plate Main Board PE Sensor Cover with acetate tape (x2).
  • Page 44 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Printhead/Adapter Cover PF Driven Pulley Assy / PF Timing Belt Main Frame Main Frame Dowel CR Unit CR Unit Compression Spring 5.07 PF Driven Pulley Assy Hook Printhead Combination Gear 29.2,42 PF Motor Frame PF Driven Pulley Assy...
  • Page 45 After installing the PF Encoder Sensor, confirm the PF Scale does not touch the PF Encoder Sensor. 6. Secure the CR Driven Pulley Assy wit the screw. CR Driven Pulley Assy / CR Timing Belt (L365/L366,L360/L362,L310/L312 Series) Pump Unit Step 1-2...
  • Page 46 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Ink Supply Tank Assy PF Grounding Spring Top Cover Top Cover Top Cover Label Left PF Grounding Spring leg A Spring Cutout Spring leg B Ink Supply Tank No color position Spring leg B Main Frame...
  • Page 47 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Bottom Cover / Left Cover / Right Cover / Cover Joint Ink Supply Tank Tube Assy Joint Left Cover Cover Joint Black 387 ± 1 mm Yellow 358 ± 1 mm Magenta 330 ± 1 mm Cyan 311 ±...
  • Page 48 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Ink Supply Tube Assy Tube Guide Sheet / Tube Guide Sheet Sub Step 6 Ink Supply Tube Assy: Step 1 Adapter CR Unit Markings (on the back) Tube Guide Sheet Black Hole 1 Hole 2 Yellow...
  • Page 49 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Tray Front Rail Left/Tray Front Rail Right, Tray Front Assy (L310/L312,L130/L132 Series) Housing Upper Assy (L310/L312,L130/L132 Series) Housing Upper Assy Frame Base Sheet: Do not remove Bottom Bottom Tray Front Assy Frame Base Section A Dowel and...
  • Page 50: Routing Ffcs/Cables

    Fold the Panel FFC aligning it with its folded lines, and then connect the FFC to the connector (CN1) on the Panel Board firmly. • Panel FFC (CN2: L365/L366,L360/L362,L220/L222 Series only) • Wireless LAN Module cable (CN4: L365/L366 Series only) • Scanner FFC (CN11: L365/L366,L360/L362,L220/L222 Series only) Note: This product does not have any panel grounding wire.
  • Page 51 Align the Head FFC and CR Encoder FFC, and then route them through the FFC Holder as shown in the figure above. Put the ferrite core into the position shown in the figure above. CR Motor Scanner Motor (L365/L366,L360/L362,L220/L222 Series) Grounding wire Scanner Motor...
  • Page 52 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Scanner FFC (L365/L366,L360/L362,L220/L222 Series) PF Motor Bottom of Scanner Carriage PF Motor cable Scanner Carriage Frame Base Connector of Relay Board Hole Connector of CIS Module Bottom of Frame Base Route PF Motor cable through rib.
  • Page 53: Chapter 3 Adjustment

    CHAPTER 3 ADJUSTMENT Confidential...
  • Page 54: Required Adjustments

    When replacing the Main Board, the adjustment should be made after performing the initial setting. In this chapter, the product names are called as follows: • L365/L366 Series:L365/L366 • L360/L362 Series:L360/L362/L363 • L310/L312 Series:L310/L312/L313 • L220/L222 Series:L220/L222 •...
  • Page 55 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Table 3-1. Required Adjustment List Adjustment Type Mechanism adjustment Adjustment using the Adjustment Program Priority First dot CR motor heat PF motor heat Scanner motor Checking the CR/PF Belt EEPROM Maintenance TOP margin Head angular PF/EJ...
  • Page 56 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Table 3-1. Required Adjustment List Adjustment Type Mechanism adjustment Adjustment using the Adjustment Program Priority First dot CR motor heat PF motor heat Scanner motor Checking the CR/PF Belt EEPROM Maintenance TOP margin Head angular PF/EJ...
  • Page 57 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Table 3-1. Required Adjustment List Adjustment Type Mechanism adjustment Adjustment using the Adjustment Program Priority First dot CR motor heat PF motor heat Scanner motor Checking the CR/PF Belt EEPROM Maintenance TOP margin Head angular PF/EJ...
  • Page 58 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Table 3-1. Required Adjustment List Adjustment Type Mechanism adjustment Adjustment using the Adjustment Program Priority First dot CR motor heat PF motor heat Scanner motor Checking the CR/PF Belt EEPROM Maintenance TOP margin Head angular PF/EJ...
  • Page 59: Adjustment Program

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 3.2 Adjustment Program This section provides the operating environment, functions related to safety and privacy policy, and the adjustment item newly added of the Adjustment Program. See "3.1 Required Adjustments (p54)" for the adjustments not explained here.
  • Page 60: Scanner Motor Heat Protection Control

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 3.2.3 Scanner Motor Heat Protection Control Purpose To measure the manufacturing variation of the DC motor (Scanner) to determine the correction value used for estimating the current value of the motor. Risks if the adjust- Because the printer cannot measure the current value of the motor accurately, even if just a mechanical load...
  • Page 61: Mechanism Adjustment / Check

    (including using the Epson-specified jigs) according to this manual. If the PG cannot fall within the standard range after performing the platen gap check described in this section, first check if the unit is correctly reassembled following the instructions in this manual.
  • Page 62 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 1. Move the CR Unit to the center of the printer. 2. Place the thickness gauges (1.5 mm) on the position A shown in Figure 3-1. 80-digit side 0-digit side Figure 3-1. Position of the Thickness Gauge 3.
  • Page 63: Cr/Pf Belt Tension Check

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 3.3.2 CR/PF Belt Tension Check This section describes the CR/PF Belt tension check. This printer is designed so that the each tension of the CR Timing Belt and PF Timing Belt fall within the expected range if you correctly reassemble the unit according to this manual.
  • Page 64 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Checking the PF Timing Belt Tension Perform the PF Belt tension check before installing the PF Scale and the PF Encoder Sensor. 1. Set the following parameters to the sonic tension meter: L365/L366,L360/L362,L220/L222 Series Weight: 1.1 g/m Width: 3.2 mm...
  • Page 65: Chapter 4 Maintenance

    CHAPTER 4 MAINTENANCE Confidential...
  • Page 66: Overview

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 4.1 Overview This section provides information to maintain the printer in its optimum condition. 4.1.1 Cleaning Except for the Printhead, there are no other mechanical parts or units that require periodic cleaning. However, if need arises, clean the component observing the following instructions.
  • Page 67: Lubrication Points And Instructions

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 4.2 Lubrication Points and Instructions <Part supply as ASP> <Part supply as ASP> None None <Lubrication status when <Lubrication status when supplied as ASP> supplied as ASP> Apply grease on sides. <Lubrication Point> <Lubrication Point> 1.Contact points (x2) on...
  • Page 68 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A <Part supply as ASP> <Part supply as ASP> None None Rear left Rear right Apply grease on rib Apply grease on rib <Lubrication status when <Lubrication status when supplied as ASP> supplied as ASP> Apply inside the groove Apply inside the groove <Lubrication Point>...
  • Page 69 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A <Part supply as ASP> <Part supply as ASP> <Part supply as ASP> None None CR Driven Pulley <Lubrication status when <Lubrication status when <Lubrication status when supplied as ASP> supplied as ASP> supplied as ASP> Not lubricated <Lubrication Point>...
  • Page 70 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A <Part supply as ASP> <Part supply as ASP> Cross-section of section A Supplied as the Scanner Enlarged figure Supplied as the Scanner Apply on the center of inner Unit Unit wall (x4 points). <Lubrication status when <Lubrication status when...
  • Page 71 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A <Part supply as ASP> Combination gear 14.4,10.8 Combination gear 13.8,9.66 Supplied as the Scanner Unit <Lubrication status when supplied as ASP> Scanner Carriage Lubricated <Lubrication Point> 1. Gear sections (x2) on the Pinion Gear of the Scanner Motor 2.
  • Page 72: Chapter 5 Appendix

    CHAPTER 5 APPENDIX Confidential...
  • Page 73: Connector Diagram

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 5.1 Connector Diagram In this chapter, the product names are called as follows: L365/L366 Series:L365/L366 L360/L362 Series:L360/L362/L363 L310/L312 Series:L310/L312/L313 L220/L222 Series:L210/L211 L130/L132 Series:L110/L111 Cable connections of this printer are shown below. Scanner Unit SCN Motor CR Unit...
  • Page 74: Points To Be Checked Before Packing The Printer

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 5.2 Points to be checked before packing the printer To avoid the trouble, such as ink leaks. Products need to be packed following to the procedure mentioned below. “Highland” means that applied to the customer who is in the place where the altitude difference with service center is over 1, 000m asl .
  • Page 75 L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A Important points when hanging the Ink Tank to product’s main body 1. Set the tube to become loose curved as much as possible(Let the tube loose on the right hand) as fig4. If curve of the tube is sharp, it might make the tube kink as fig5.
  • Page 76: Protection For Transportation

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 5.3 Protection for Transportation This section describes the cautions for packing the printer before returning it to the user. 5.3.1 Securing the CR Unit Purpose To prevent damaging the Change Lever by shock during transportation. Risks if it is not performed Fatal error caused by the damage of the Change Lever.
  • Page 77: Securing The Paper Support Assy

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 5.3.2 Securing the Paper Support Assy Purpose To prevent damaging the Paper Support Assy by the shock during transportation. Risks if it is not performed The Paper Support Assy will be scratched and the abrasion powder will be produced due to the shock during transportation.
  • Page 78: Securing The Ink Supply Tank Assy/Top Cover

    L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series Revision A 5.3.3 Securing the Ink Supply Tank Assy/Top Cover Purpose To prevent damage on the Ink Supply Tank Assy/Top Cover from shock during transportation. Risks if it is not performed Damage on the Ink Supply Tank Assy/Top Cover.

This manual is also suitable for:

L360L366L310L312L313L220 ... Show all

Table of Contents