Advertisement
Quick Links
Installation Instructions
Supertop for Truck
www.bestop.com
- We're here to help! Visit our web site and click on
INSTALLATION TIME
1-1/2 Hours
TOOLS
7/16" and 9/16"
US Patent 6827391
SKILL LEVEL
2 - Moderately Easy
1/8" Bit
Vehicle Application:
• Chevrolet Silverado 1500 / 2500 / 3500 6.5 ' Bed
1999 - 2011
Part Number: 76303
"Ask a
Question". Click here for more
• GMC Sierra 6.5 ' Bed
1999 - 2011
Part Number: 76303
Truck Accessories by Bestop.
Advertisement
Related Manuals for Bestop 76303
Summary of Contents for Bestop 76303
-
Page 1: Installation Instructions
• Chevrolet Silverado 1500 / 2500 / 3500 6.5 ' Bed • GMC Sierra 6.5 ' Bed 1999 - 2011 1999 - 2011 Supertop for Truck Part Number: 76303 Part Number: 76303 US Patent 6827391 www.bestop.com - We’re here to help! Visit our web site and click on “Ask a... - Page 2 Front Bow Half, Part Number 412.96, Qty - 2 Rear Bow, Right, Part Number 496.26, Qty - 1 Inner Retainer Bar, Tailgate Bar, Part Part Number 499.90, Number 496.54, Qty - 1 Qty - 1 Rev. G 0713 76303 pg. 2...
- Page 3 Bracket Front Belt Rail 1/4" x 1-1/2" Bow Mount Bracket Clevis Pin Rear Pivot Hole 5/16" Flat Washer Front Slot Rear Belt Rail 1/4" Fender Washer 5/16" x 3/4" Clevis Pin 1/4" Flat Washers Rev. G 0713 76303 pg. 3...
- Page 4 Place them so that they are 63-1/2" at both places and are centered and square on the bed. Measurement between Rails should be 63-1/2" 1/4" Front Bow Halves Bow Tie Down Front Edge of Straps Front Wall Belt Rail Assembly Rev. G 0713 76303 pg. 4...
- Page 5 Rear Bow Assembly over the 5/16" x 3/4" Clevis Pins and secure them with a 5/16" Flat Washer and a Hitch Pin Clip on each side of the vehicle. Pull Strap Hitch Pin Through Clip Rev. G 0713 76303 pg. 5...
- Page 6 Short Bow Drape Fabric Wrap Flaps from over Cab front and Snap to Bow Wrap Flaps from Rear and Snap to Bow Rear Bow Rear Window Opening Elastic Elastic Garter Garter Rev. G 0713 76303 pg. 6...
- Page 7 Front Retainer Place the Front Bow on the rear tooth at the front of Bar Bracket the Bow Mount Bracket. Front Bow Place Bow in rear tooth of Bow Mount Bracket Front Retainer Bar Front Rev. G 0713 76303 pg. 7...
- Page 8 Peel the backing tape off the bottom of the mounting pad and press it onto the bow. Thread Wire through Snap Flap Drill 0.136" Drill 0.136" Hole and Holes install #8 x 1/2" Self Tapping Screws Press Light onto center of Rear Rev. G 0713 76303 pg. 8...
- Page 9 Locate the Tailgate Bar and the Bulb Seal in the parts kit. Slide the channel in the Bulb Seal over the ledge on the Tailgate Bar. Slide Rear Retainer Bar onto Rear Window Fasten Snap Rev. G 0713 76303 pg. 9...
- Page 10 Quarter Panel Elastic Garter around each end of the window. Roll Rear Window Side Rail Tailgate Opening Elastic Garters Plastic Strip - Slip into Channel Rev. G 0713 76303 pg. 10...
- Page 11 Fold the glass under and toward the front of the bed. Collapse Front Pull the 32" Buckle Strap about halfway outside the top. Slide Front Bow out of teeth Rev. G 0713 76303 pg. 11...
- Page 12 Belt Rail. Wrap the straps around the bows and hook the plastic strip on the end of the strap into the channel in the Side Belt Rail. Hook Plastic into Channel in Belt Rail Rev. G 0713 76303 pg. 12...
-
Page 13: Limited Warranty
Your Bestop product is made of the fi nest materials available. To keep it looking new and for the maximum possible wear, it will need periodic cleaning and maintenance. Fabric: The fabric should be washed often using soap, warm water and a soft bristle brush Rinse with clear water to remove all traces of soap. Bestop recommends using Bestop Cleaner (part no.