Advertisement

Dream On Me Inc.
125 Helen Street
S.Plainfield NJ 07080
TEL: 908-791-0555
FAX: 908-791-1809
Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed please find simple step-by-step instructions to help you
quickly assemble your products. Before you begin we recommend
that you following the steps below:
1. Please read the instructions thoroughly.
2. Identify all parts and hardwares.
3. You will need the following tools:
Philips head screw driver
Flat head screw driver
Hammer
Do Not Use Power Drills or Drivers
To protect your parts during assembly please place them on a soft
surface.
To clean surface use only water on a damp cloth. Do not use
window cleaners or cleaning abrasives as it will scratch the surface
and could damage the protective coating.
Notez s'il vous plaît que l'avertissement sur la table à langer
est exigé par la loi de la CPSC et l'ASTM, qui nous oblige d'in-
former les parents et les personnes en charge des enfants.
Nous nous excusons pour toute inconvenance que cela pour-
rait vous causer.
L'assemblage par un adulte de ce meuble est nécessaire.
Les petites pièces non-assemblées présentent le risque d'étouffement.
Pour vous aider pendant l'assemblage de votre produit, veuillez trouver
en bas des instructions simples, en étape. Avant de commencer
ASSEMBLY INSTRUCTIONS
INSTRUCTIONS D'ASSEMBLAGE.
ITEM NO: 649
NUMÉRO DU MODÈLE : 649
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 649 and is the answer not in the manual?

Questions and answers

Summary of Contents for Dream On Me 649

  • Page 1 125 Helen Street INSTRUCTIONS D'ASSEMBLAGE. S.Plainfield NJ 07080 ITEM NO: 649 TEL: 908-791-0555 NUMÉRO DU MODÈLE : 649 FAX: 908-791-1809 Adult assembly required. Small parts may present choking hazard prior to assembly. Enclosed please find simple step-by-step instructions to help you quickly assemble your products.
  • Page 2 l'assemblage, les étapes suivantes sont vivement recommandées : 1. Lisez attentivement les instructions. 2. Identifiez toutes les pièces et les outils. 3. Vous avez besoin des outils suivants : Tournevis cruciforme Tournevis plat Marteau N'utilisez pas d'outils électriques. Pour protéger les pièces pendant l'assemblage, placez-les sur une surface souple.
  • Page 3 THE SCREWS AND NUTS REMAIN TIGHT. · NEVER USE THIS PRODUCT IF THERE ARE ANY LOOSE, MISSING FASTENERS, LOOSE JOINTS,BROKEN PARTS, OR TORN MESH/FABRIC.CONTACT DREAM ON ME 125 HELEN STREET S.PLAINFIELD NJ 07080 908-791-0555 FOR REPLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED.
  • Page 4 JOINTS SONT LÂCHES, SI DES PIÈCES SONT FAUTIVES OU SI LE TISSU PRÉSENTE DES DÉCHIRU- RES. POUR DES PIÈCES DE REMPLACEMENT ET DES INSTRUCTIONS D’ASSEMBLAGE, CONTAC- TEZ DREAM ON ME 125 HELEN STREET S.PLAINFIELD NJ 07080 908-791-0555. NE PAS SUBSTITUER DE PIÈCES. CE PRODUIT, Y COMPRIS LES REBORDS, DOIT ÊTRE ENTIÈRE- •...
  • Page 5 PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT. D. Left front leg (1pc) C. Left back leg (1pc) A. Headboard (1pc ) B. Footboard (1pc) G. Right bed rail (2pcs) H. Left bed rail (2pcs) F. Right front leg (1pc) E.
  • Page 6 PARTS: HARDWARE KIT IS PART #21598 FOR COLOR 209 OR #23486 FOR COLOR 607. SEE FRONT COVER. No drills necessary. Do not use power a.3’’Allen head bolt(12pcs) screwdriver Phillips Screwdriver (not supplied) b.2-3/8’’Allen head bolt(28pcs) c.1-4/5’Allen head bolt(4pcs) f. 1-5/8”Wood dowels (4pcs) d.Barrel nuts (40pcs) g.
  • Page 7 SECTION 1: Crib Assembly STEP 1 Parts and tools required to complete step. B. Footboard (1pc ) E. Right back leg (1pc) F. Right front leg (1pc) b.2-3/8” Allen head bolt (6pcs) d. Barrel nuts (6pcs)   J. Top rail (1 pc) f.
  • Page 8 SECTION 1: Crib Assembly STEP 2 Parts and tools required to complete step. H. Left bed rail (1 pc) From step 1 g. Allen wrench (1pc) a.3’’Allen head bolt(3pcs) d. Barrel nuts (3pcs) Using the bolt (a) and the barrel nut (d) to connect the front left bed rail (H) to right board(B) .
  • Page 9 SECTION 1: Crib Assembly STEP 3 Parts and tools required to complete step. N. Cross Bar (3PCS) M .Cross Bar (1 PC) From setp 2 b.2-3/8’’Allen head bolt(2pcs) d. Barrel nuts (2pcs) g. Allen wrench (1pc)
  • Page 10 SECTION 1: Crib Assembly STEP 4 Parts and tools required to complete step. a.3’’Allen head bolt(3pcs) G. Right bed rail (1pcs) From step 3 b.2-3/8’’Allen head bolt(2pcs) d. Barrel nuts (5pcs) g. Allen wrench (1pc) Repeat the step 1 - step 4 to assemble the footboard, by using the parts for the footboard in the parts list.
  • Page 11 SECTION 1: Crib Assembly STEP 5 Parts and tools required to complete step. K.Middle bar (1pc) c.1-4/5’Allen head bolt(2pcs) From step 4 f. 1-5/8”Wood dowels (2pcs) e. Spacer (2pcs) g. Allen wrench (1pc)
  • Page 12 SECTION 1: Crib Assembly STEP 6 Parts and tools required to complete step. L .Cross Middle Bar (2 pcs) From step 5 b.2-3/8’’Allen head bolt(4pcs) d.Barrel nuts (4pcs) g. Allen wrench (1pc)
  • Page 13 SECTION 1: Crib Assembly STEP 7 Parts and tools required to complete step. b.2-3/8’’Allen head bolt(4pcs) c.1-4/5’Allen head bolt(4pcs) K.Middle bar 2( pc) From step 6 e. Spacer (4pcs) g. Allen wrench (1pc) d.Barrel nuts (4pcs)
  • Page 14 SECTION 2: Chairs and Table Assembly STEP 1 Parts and tools required to complete step. Legs(4pcs) Table top(1pc) Not supplied Not supplied g. Allen wrench (1pc)
  • Page 15 SECTION 2: Chairs and Tbale Assembly STEP 2...

Table of Contents